Interior

New Old Stock 1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was used and the surrounding bezel would be labeled "Top" or "Defog" in the farthest position to the right. The fourth switch is never used on the 1969 xr7, it is just there to...

1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. Switches sold pit free on the chrome. Switches guaranteed to work, but are likely stiff. Electro solvent usually helps with that sticking condition, see product label for directions prior to use. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the steering...

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang, and most 1965-69 Ford and Mercury full sized cars such as Galaxie, Monterey, Parklane, Montclair, etc.Fits 67 CougarFits 68 CougarFits 65 Mustang Fits 66 MustangFits 67 MustangFits 68 Mustang

If you have already begun to install or have installed this item, it is not eligible for return or refund. This is far superior to the switch Ford put out as a service part in the 90's. It is imperative that you clean every part of your old switch out before carefully installing the new switch. It is best to start both ends at the same time at 6 o'clock and meet at the middle at 12 o'clock. It measures 44" in length. We've found that these switches are about an inch too long, so you'll...

For two spoke steering wheel. Two pressure switches with connection terminals installed into black plastic holder. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part # D2AZ-13875. Fits standard or deluxe steering wheel inserts.

Sold individually, three of these are mounted to your 1967 steering wheel. Comes with two screws as shown. Also sold in a set of 3. Check out this video

Sold in a set of 3, these are mounted to your 1967 steering wheel. Comes with two screws as shown. Also sold individually. Check out this video ...

Hard to find New Old Recent Stock switch for the driver side power seat on the 71 - 73 Cougar or Mustang. Toggle switch looks accurate, however, you will need to reuse your original plugs. PLUGS NEED TO BE CHANGED FOR SPECIFIC APPLICATION. Some of the Ford part numbers include: D1WB-14B723-AA, D1WB-14B723-Ab, D2WB-14B723-AC, D1ZB-14B723-AA, D1ZZ-14A701-A, D2WY-14A701-A.

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. The relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to illuminate the directional arrows on the dash and does...

Replacement turnsignal switch for all 1968 Mercury Cougar and Ford Mustang with fixed (non-tilt) steering columns. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. The relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to...

Our turn signal switches are made by the original supplier to Ford from the original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This...

NOTE!!!! This offshore switch is assembled with plated steel rivet contacts as opposed to brass rivet contacts like original. Whereas the Torino or Mustang do fine with 2 incandescent rear bulbs the Cougars with 6 bulbs put too much load on the switch and they fail. The only way these switches will hold up in a Cougar is if you convert to LED. We are hoping the supplier will take our advice and correct this problem but until such time we cannot warranty this product. Don Rush 9-11-2017 1970-72...

Our turn signal switches are tested and working. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch.Replaces Ford part # D2AZ-13341-C. Replaces Ford...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This turn signal switch for the 1967 Cougar equipped with the tilt / tilt away steering column is made using the original tooling acquired from the original manufacture of this part that Ford purchased these switches from when they were originally installed new in the Cougar. If you have replaced your sequential unit in the trunk with one of our new solid state sequential...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. For 1968, the relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to illuminate the directional arrows on the dash...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This switch also fits the 1970-1972...

Unlike the reproduction, we have this available in multiple colors. Call for availability. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Ford part # D1ZZ-13915-A Used in conjunction with the deluxe trim plate.

This little cover glues onto your spoke at 6 o'clock and serves to cover the gap between where your rubber horn switch starts and then stops. NOTE: The 69 steering wheel does not take one of these covers because the bottom of the horn pad actually comes down far enough to cover the rimblow gap spacing.Replaces Ford Part #: D1ZZ-13875-C. Check out this video

For two spoke steering wheel, comes in black only. Exact reproduction with correct grain texture. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part #D0ZZ-13915.

Advantages of  Pre-Sending Cores:- Ships after we receive your 1967, 1968, 1969, or 1970 Mercury Cougar XR7 tachometer, (Yes, any factory installed Mercury Cougar tachometer from 1967-1970 is acceptable) avoiding unnecessary core charges. Tested and working 6000 RPM tachometer with correct emergency brake indicator light lens and plain green lens. 1969 Mercury Cougar XR7 and Eliminator models only. Ford part number C9WF-17360-A.*Note - Boss 302 Eliminators normally received 8000 RPM...

Tested and working all metal 6000 RPM tachometer with correct Seat Belt and Lights indicator lenses. 1970 Mercury Cougar XR7 and Eliminator models only. Ford part number C9WF-17360-A. There is a second manufacturer (See other listing) of this 1970 tachometer which was manufactured by Faria Instruments. It is identified by having a plastic rear housing and a rest for the needle. It has a part number of C9WF-17360-A2. *Note - Boss 302 Eliminators normally received 8000 RPM tachometers.*Note -...

Good used original working tachometer. We will accept your core even if the face is faded or scratched. Please include a copy of your invoice when sending a core.Check out the video below on our new gauge tester: ...

This tachometer was only used on the 1970 BOSS 302 Eliminator but occasionally found its way into other models. This is a tested, working original part. 70 differs from 69 only in the indicator lights at the bottom.Check out the video below on our new gauge tester: ...

This tachometer was only used on the 1969 BOSS 302 Eliminator but occasionally found its way into other models. This is a tested, working original part. 69 differs from 70 only in the indicator lights at the bottom.Check out the video below on our new gauge tester: ...

Requires a $50 refundable core charge, send us your dummy plate for a core refund! No, Mercury never offered an in dash tachometer for your 1969 - 1970 Decor or Standard model Cougar... For years people have been "making" 2 wire tachometers from xr7 and Eliminator Cougars work (kind of). This is a brand new three wire tachometer custom made to look and fit like the original would of had they been available in the day.  If you would like to retain the original standard clock we now have a...

Three wire tachometer for 67 - 68 Cougar. Ford wired their early (pre ‘74) tachometers so that they are part of the ignition circuit. What this means is that if the tachometer goes bad, the engine shuts OFF. It also means that you must either replace it with another series type tachometer with 35+ year old circuitry or install a jumper wire to bypass the tach. It also means that you need a special adapter to use your factory tach with an MSD ignition box. Our three wire tachs are independent...

Requires $65 Core Charge. Return your core to us for a $65 refund! Three wire tachometer for Cougars. Ford wired their early (pre ‘74) tachometers so that they are part of the ignition circuit. What this means is that if the tachometer goes bad, the engine shuts OFF. It also means that you must either replace it with another series type tachometer with 35+ year old circuitry or install a jumper wire to bypass the tach. It also means that you need a special adapter to use your factory tach with...

New temperature sending unit for the 1970 - 1971 Mercury Cougar and Ford Mustang with an actual temperature gauge and a 428, 428CJ (Cobra Jet) or 429CJ (Cobra Jet) engine. Replaces Ford Part #: D0ZZ-10884-A (SW-925)Check out the video below on our new gauge tester: ...

Nice new black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Replaces Ford Part #: D1ZZ-9735 and D1ZZ-9735-A

These differ from 68-69 in that there is no starter safety switch embedded in them. This is a used part, tested, lubed, and working. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.

C7WB-13713-A New old stock XR-7 dash toggle switch for the "Panel" light on the 1967-68 Cougar. This switch has the black plug, and it will work for the "Courtesy" light switch too, those are typically have red plugs though.

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Ignition bezel adapter tool removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included.  ...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Ignition bezel adapter tool removes and installs ignition switch bezels on any 1969 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included.  ...

Adapter tool for installing and removing remote door mirror bezels on 1967-68, and 1970-73 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included. *Note - Excludes 1969 remote mirror bezels. ...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels on any 1967-70 Mercury Cougar or Ford Mustang. Additionally, it also removes the wiper switch on 1969-70 Mercury Cougar and Ford Mustang. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68, or 1969...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. We also have a handmade version of this same tool for a lower price.

This is a ignition nut tool used to take the ignition nut out of 1969 Cougar. These are made from HRS steel and are milled to fit the bezel. No more scratches trying to remove with the wrong tools.

No more screw drivers or pliers to get that 1969 unique mirror nut loose! Works for the chrome and sport driver side remote mirror for 1969. Keep in mind that these tools are designed to fit the original mirror nut, we've found that they don't fit well on the reproductions. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some...

This is a bezel nut tool used to remove the toggle switch bezel nuts on 67 - 68 & 71 - 73 XR7 Mercury Cougars. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This is a MUST HAVE if you are replacing a toggle switch or taking apart your dash, we use this tool in our shop all the time and love it!

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. A 5/32" Allen wrench is needed to attach tools together. Allen wrench included.  ...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch and wiper switch bezels. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1969 Mercury Cougar and Ford Mustang. A 5/32" Allen wrench is needed to attach tools together. Allen wrench included.  ...

Slightly wider than the 1967 version. Customer feedback at mercurycougar.net: I did a drum to disc conversion on my '68 a few months ago. WCCC sold me 2 orig. cougar brake setups from spindle to caliper to brake lines with the P. valve , you know complete.. These freaking brakes looked like they were a year old, no sh**. I had my Friend Perry from "Perry's Pony Express" a Classic Mustang restorer here on Long Island help me install them & he told me they were the cleanest 1968 used brakes...

Replaces Ford part #: C7ZZ-3656-A, concours correct for all 1967 Mustang's and Cougar's. This beveled ornamental plastic ring is for your 1967 steering wheel hub. The inner diameter is 3 3/4" and the outer diameter is 4 3/8" and it stands 5/16" tall. This ring fits many FoMoCo products but keep in mind there is another version that is completely flat like a washer. We suggest you use soapy water and heat your hub before trying to slip this on. It also helps if you go around the perimeter and...

*NOTE* 1969 - 1970 Convertible mats do not have any covering to the right of the gas tank. This is in fact how the originals were made. Many Convertible owners prefer to have a full cover mat. If that is you we suggest you purchase the coupe mat for your convertible.This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern. Do NOT confuse this with the light duty mat you will see...

This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray speckled pattern for 1971 - 1973. Do NOT confuse this with the light duty mat you will see elsewhere listed for the same money or less. The budget mats you see elsewhere weigh only a few ounces and flail around inside your trunk every time you close the lid! The pattern will not smudge or wear off easily and it will lay flat and fit perfect the...

This reproduction is pathetic... It is made from the same material as a cheap picnic table cloth (you know, the red checkered ones?) The only way you will ever get this plastic "table cloth type" mat to lay flat is to glue it down. They do however work well for catching oil spills under your Cougar when turned felt side up. The correct dark gray speckled pattern for 71 - 73 is not available with this mat. No returns on this product, we suggest no mat is a better alternative than this poor...