Interior

This reproduction is pathetic... It's made from the same material as a cheap picnic table cloth (you know, the red checkered ones?) The only way you will ever get this plastic "table cloth type" mat to lay flat is to glue it down. They do however work well for catching oil spills under your Cougar when turned felt side up. No returns on this product, we suggest no mat is a better alternative than this poor quality reproduction. It's that bad... Please look at our premium quality trunk...

This reproduction is pathetic... It is made from the same material as a cheap picnic table cloth (you know, the red checkered ones?) The only way you will ever get this plastic "table cloth type" mat to lay flat is to glue it down. They do however work well for catching oil spills under your Cougar when turned felt side up. The correct dark gray speckled pattern for 71 - 73 is not available with this mat. No returns on this product, we suggest no mat is a better alternative than this poor...

This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern by Auto Custom Carpets. Do NOT confuse this with the light duty mat you will see elsewhere listed for the same money or less. The budget mats you see elsewhere weigh only a few ounces and flail around inside your trunk every time you close the lid! The pattern will not smudge or wear off easily and it will lay flat and fit...

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

New Old Stock turn signal switch for fixed steering columns on 1968-69 Mercury Cougar and Ford Mustang.Replaces Ford part # C8SZ-13341-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

New Old Stock turn signal switch for any 1969 Mercury Cougar or Ford Mustang with fixed steering columns. This switch will also fit fixed column Ford's 1968-1969 Ford Crown Victoria / Full Size / LTD / Fairlane / Torino / Falcon / Galaxie & 1970 Mercury Comet / Ford Falcon / Early 1970 Ford Maverick / Mercury Comet without locking steering wheel & all 1968-1969 Mercury Comet's Ford part # C9AZ-13341-B.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the...

Our turn signal switches are made by the original supplier to Ford from the original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This...

Our turn signal switches are made by the original supplier to Ford from the original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This...

Quality switch that is getting increasingly hard to find these days. This same switch was used in the 1977-1979 Ford Thunderbird / 1972-1976 Ford Fairlane / 1977-1979 LTD II / Ranchero / Torino and Elite / 1975 Mercury Monarch without Instrument mounted windshield wiper switch / 1974 - 1976 Mercury Montego*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist...

Used steering column wiring harness plug. Replacement plug for all 1968-69 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968-69, Ford, Mercury, & Lincoln. This plug is natural or white, there is also a black color version of this plug used by Ford 1970-72.Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject....

New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.

Metal portion of the driver side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at least...

Metal portion of the passenger side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at...

Used vacuum actuator for the tilt / tilt away steering column in the Mercury Cougar, Ford Mustang or Thunderbird. This unit was used through late 1968 and 1969 and has the embedded safety starter switch in good working order. 1967 through early 1968 actuators are white, where these units are black in color. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at...

Used vacuum release valve for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This vacuum solenoid releases the steering column for the swing away function. These vacuum tilt solenoids are tested and guaranteed to work. Bench testing the 1967-69 tilt away release solenoid: Verify that there is continuity between the two electrical spade connectors. No continuity means the the windings in solenoid windings are bad. This is a bad solenoid. Next, put vacuum to...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Vacuum / electric tilt away solenoid for the 1969 Mercury Cougar and Ford Mustang. Original Ford part number C9ZZ-3D536-A. These vacuum tilt solenoids are tested and guaranteed to work. Bench testing the 1967-69 tilt away release solenoid: Verify that there is continuity between the two electrical spade connectors. No continuity means the the windings in solenoid windings are bad. This is a bad solenoid. Next, put vacuum to the lower port (10-17 inches of vacuum) any handheld or car vacuum...

Vacuum reservoir that mounts under the battery tray for factory tilt swing away steering columns. Fits Cougar, Mustang, and Thunderbird. Single nipple tank, we also sell the double nipple tank for the 1967-68 tilts. Replaces Ford Part # C9ZZ-3E547-A. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* WCCC...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

New old stock passenger side vent window handle for any 1968 Mercury Cougar or Ford Mustang.  Drive pins and washers included.Ford part number C8OZ-5422916-B.

Pressure die cast in zinc and heavily chrome plated. Excellent quality. Drive pins and washers included, sold as a pair.

Reproduction driver side (left hand) vent / wing window handle for the Mercury Cougar or Ford Mustang.

Reproduction passenger side (right hand) vent / wing window handle for the Mercury Cougar or Ford Mustang.

These are original amp meters converted from reading amps to reading volts. Includes new matching XR7 overlay made from top quality 3M 467MP and use 200MP adhesive. The longer 200MP adhesive is in place the stronger it binds. Optional Volt decal is included. Click here for a article describing the advantages of a Volt Meter. Check out the video below on our new gauge tester: ...

Is your 67 - 68 Cougar or Mustang having some electrical problems? Are your dash gauges not working like they used to? If so, you should consider a new voltage regulator. Features & Benefits: - Improved Design for Better Reliability and Accuracy in Heat, Humidity and More- Solid State Electronic Circuitry and Variable Controls- Made of Premium Materials for Durability- Mounts Behind Your Dash GaugesReproduction Constant Voltage Regulator features an improved design that makes it more reliable...

Affixes to the back side of your cluster. Far superior to the current reproduction units that are available.Check out the video below on our new gauge tester: ...

We cannot provide new units anymore but we do stand behind this used unit for 30 days.Check out the video below on our new gauge tester: ...

This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...

Warning light panel from a 1969 or 1970 Eliminator model Mercury Cougar. This is a modified light panel for the center of the dash. We mill out the raised portion of the bezel where the lights are framed. We mill flat the panel so that the reproduction block off plate can be attached flush with the panel. Eliminator block off plate sold separately. Ford part number C9WY-10C854-B.

New Old Stock Warning light panel from a 1970 Standard model Mercury Cougar. This is the light panel in the center of the dash. There are four visual check items that light up, 'BELTS', 'LOW FUEL', and 'DOOR AJAR', 'LIGHTS'. This one has a black rubber trim. Ford part number D0WY-10C854-A.

Warning light panel from a 1969 Standard model Mercury Cougar. This is the light panel in the center of the dash. There are three visual check items that light up, 'PARK', 'LOW FUEL', and 'DOOR AJAR'. Specify the color of rubber in the comments or notes. Keep in mind that most of the colors fade or change colors due to UV light and age. Also realize that the rubber trim has shrunken, and may have poor fitment. Plan on dying the rubber trim and re-gluing it to this chrome panel. The 1970 panel...

Warning light panel from a 1970 Standard model Mercury Cougar. This is the light panel in the center of the dash. There are four visual check items that light up, 'BELTS', 'LOW FUEL', and 'DOOR AJAR', 'LIGHTS'. Specify the color of rubber in the comments or notes. Keep in mind that most of the colors fade or change colors due to UV light and age. Also realize that the rubber trim has shrunken, and may have poor fitment. Plan on dying the rubber trim and re-gluing it to this chrome panel. The...

Used rubber washer for the locking pawl cable to cable guide used for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This unit fits against the cable side of the ninety degree angle. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts...

Used on all four 1967 belts for a total of 8 per car. Found to be slightly dished on most examples we see.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Used on the retractors.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

Same as 69-73 but with no markings.

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

Reproduction aqua headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction aqua rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...