Interior

If your automatic floor shifter has play in it left to right then this is the culprit. Easy to install, (more difficult if you have a 67-68 with center console) these are made from a wear resistant plastic that is better than original. Sold as a pair as two are required per car. This bushing was used in all Ford products equipped with a floor shift automatic from the 1965 Mustang to the late 70's Pinto. Replaces Ford Part # C5ZZ-7A133-A Check out our video on rebuilding your shifter below: ...

Rechromed 1967 deluxe shifter button. Unique to the deluxe faux leather wrapped T handle shifter starting in 1967. One year only design, this one has a convex button for you thumb. Starting in 1968 the button was more rounded to comply with the added safety features mandated in 1968. Core deposit is required, fully refundable with returned 1967 deluxe button. Ford part number C7ZZ-7C488-B. Check out our video on rebuilding your shifter below: ...

This group of parts mounts to the top of the AT shifter arm and rides against the thumb activated button on your T shift handle. Its function is to lift the cable that runs through the chrome shifter stem to lock and unlock the shifter out of Park. The Ford technical name for this part is 'Roller - Shift Lever Lock'. We carefully inspect each part to make sure it is in perfect used condition. Ford part number C5ZZ-7D328-A. Check out our video on rebuilding your shifter below: ...

Exact reproduction for the 1969 - 1973. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one. Replaces Ford Part #: C8OZ-7213-A, C90Z-7213-B, D3OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Not a very good color match for Cougar owners, but will work well with blue interiors.Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Allen head set screw for all stock Ford automatic shifter handles on any 1967-73 Mercury Cougar or Ford including Mustang. Uses the same 3/32 inch allen wrench for attaching as the originals. Most handles take two of these set screws, one on the dummy button, and one to attach to the top of the shifter lever. The 1973 all chrome shift handle only uses one of these set screws. Original Ford part number 374985-S. Check out our video on rebuilding your shifter below: ...

Reproduction automatic shifter lever in chrome for the Mercury Cougar or Ford Mustang. Comes with inside cable parts. See the related items for more of your shifter needs. Check out our video on rebuilding your shifter below: ...

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The early versions used the C5ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The late versions used the C9ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

Adjustable rod that connects the floor shifter to the "Select-Shift" automatic transmission. C4 transmissions only, code "W" on your door data plate tag. All 302 and 6 cylinder engines received the C-4 automatic transmission. Rod with casting number C9ZA-7326-D. Shift rod approximately 17-1/4 inches long. 1969 Ford Mustang only. Check out our video on rebuilding your shifter below: ...

Reproduction adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions.Includes pin and nut. Shift rod approximately 18 inches long. Replaces Ford part number marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions. Shift rod approximately 17 inches long. Rod marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

Used angled chrome spacer for any 1969 Mercury Cougar or Ford Mustang. Good used part with very good chrome plating, usually one of the small locating tabs will be broken off of the back. Still a great value compared to the reproduction, and installs fine without the one tab on the back. Replaces Ford part number C9ZZ-11574-A.

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange. Ford part # C9SZ-3C708-A.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.

This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original decal with starburst design. Spring is included. Check out our video "All about seat belts" below.

Better quality than our reproduction for less money. Ford part number C0DZ-13807-A.

Large seat track spring for the latch. Used about 6-1/2 inches long, and about 9/16" thick.  Listed for bucket seats 1965-1970 Mercury Cougar and Ford Mustang. Likely fits other Ford seats, has a 1960 Falcon part number. Ford part number C0DZ-6461883-A.

This gives the thumb release button in your T shaped shift handle its tension. If it is rusted then your button will not return back to its outer position easily. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Technically this spring fits all Ford and Mercury floor shifters 1965-73. Ford part number C5ZZ-7C300-A. The MPC shows this spring to have a free length of 2-1/16 inches.

Used steering wheel tension spring used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. Keeps tension on the steering wheel shaft so as to keep the steering wheel from contacting the upper column cover. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC...

Used spring cap that is used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This clip is the same as a door panel clip with the exception that it does not have the foam spacer. This clip was used on the 1968 XR7 overhead console, 1967 - 1968 xr7 and standard model upper and lower console pads, seat back access panels and several other applications. This original clip holds tighter than the reproduction. We recommend using this used clip over our reproduction for applications like the seat back because the reproductions often do not cut it. Ford part number...

Don't try to straighten your rod if it looks like this. The contour seen here is correct. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 

Used tilt / tilt away steering column converted into a tilt only unit for the Mercury Cougar or Ford Mustang. All 1967-69 Cougars and Mustangs optioned with a tilt column also had the tilt-away (aka tilt-swing, tilt-fly or tilt-pop). There was never a tilt only option in 1967-69 Cougar or Mustang, no matter what you may have been told... That being said some of our customers prefer not to have the added expense or complexity involved with the swing-away function. This column has been fused at...

Fixed steering column from a 1969 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. Upper and lower mounting brackets, are available, but sold...

This is my most favorite Cougar - Mustang - Shelby option of all time! In fact as a rather tall person, that is not as slim as I once was, I do not really enjoy driving a Pony car that does not have this option anymore. This column does not only manually adjust up and down with the depression of the turn signal wand, it also releases and swings up and towards the passenger side of the car each time the ignition is turned off and the door is opened. To start the car you must close the door and...

Reproduction rim blow steering wheel for any 1969 Mercury Cougar or Ford Mustang, and generally any other Ford Lincoln or Mercury with tri-spoke rim blow steering without speed control. Brand new to market, black is the only color. Rim Blow Switch not included. We asked long time Cougar collector and restorer Randy Carlson to give us his honest opinion of this new to the market wheel and this is how he responded; "Be ready to cut the box to pieces to get the wheel out of the packaging. It...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad.

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Note that the color on these has too much gray in it and is...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Check out this video ...

Pictured in black. This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Check out this video ...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad.

Core wheel good only for restoration. We have a very hard time keeping these in stock due to their popularity in Australia. If you have any 1969 3 spoke rim-blow steering wheels for sale we would like to hear from you! 503-463-1130 Check out this video

Please email us for color on hand, rarely do we have more than one grade A in stock. Grade A will have almost no warping or lifting issues, soft and pliable and will not need repaint. Very hard to find, one year only part.

Good used pad available in most colors, please let us know which color you need in the comments section and we will try to accommodate. Grade B pads will be lifting at the top, be a little warped and have some missing texture where your thumbs often ride at 3 and 9 o'clock.

Not the best fit, texture is incorrect. Guaranteed disappointment, no returns on this item please.

Excellent quality reproduction sun visor assemblies and corner trim for the convertible 1969 - 1970 Mercury Cougar or Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. Sold as a pair, the original passenger side part has a C9ZB-7604122-C casting number on the back side and the driver side reads C9ZB-7604123-C. These will also interchange with versions ending in A B or D. Later versions will show one less screw tab. Replaces Ford part # C9ZZ-7604144 /...

Used single hole front mount center visor bracket for the 1969 / 1970 Mercury Cougar and Ford Mustang hard tops.  The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your desired color in the 'comments' section of your order. Ford part # C9AZ-6204132, casting # C9AB-6204132-B.

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Reproduction single hole front mount center visor bracket for the 1969 and 1970 Mercury Cougar or Ford Mustang. This is a decent reproduction, but not quite as nice as the originals. Reproductions only come in 'paint to suit' black but we have most original colors in used. Replaces Ford Part #: C9AZ-6204132.