Fasteners

replaces Ford part # 385161-S Zinc - Dichromate (yellow - rainbow) finish

Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

Reproduction 8-32 x 1/2" stud used to attach the convertible boot mouldings on any 69-73 Cougar or 65-73 Mustang. A number of these studs were installed on the mouldings, going through the body of the car and attached underneath the sheet metal using the boot nuts.

Sold as a pair. Replaces Ford Part # : D0OZ-8052 Check out our video on Radiator and Fan upgrades below:

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

Sold individually Zinc (dark silver)

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

Sold individually, phosphate & Oil (gray-black).

A nice reproduction of the standard air cleaner wing nut. This version was used on most Ford products through the 1980's.

Master clip kit which includes the following fasters:Back up light to firewallDoor speakersEngine ffeedRadio cable to dashSide marker and headlightsTaillight wiring and groundUnder dashVarious location zip tiesKeep in mind that not all fasteners found on 1971-73 Cougars / Mustangs are in this kit.

Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold as a set of 4. Concours phosphate & Oil (gray-black).

Dash pad attaching nut 8-32 threads original zinc plate and dichromate. 5 of these nuts are used to attach the dash pad to the painted steel upper dash panel  (D1ZZ-65044D90-A) on 1971-73 Mercury Cougar and Ford Mustangs. Sold individually.Replaces Ford part number 45271-S36.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.