Fasteners

Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.

Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K

replaces Ford part # 385161-S Zinc - Dichromate (yellow - rainbow) finish

Fits Standard and XR7

Used Strap - Large Wire Loop for the 1968 Mercury Cougar or 1968 Ford Mustang

Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

Stud for attaching heat shield to passenger side exhaust manifold. Fits all 1968 Mercury Cougar or Ford Mustang and other Ford too. Sold individually. Phosphate & Oil (gray-black)

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design. Two different sized brackets used, this is the larger one that is 1-3/4 inches wide. The bracket that goes in the corner above the switch panel is 3/32" less. It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend...

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the smaller design. Two different sized brackets used, this is the smaller one that is 1-21/32 inches wide. This bracket goes in the corner above the switch panel. The larger bracket is 1-3/4" or 3/32" wider. It was obvious what the original intent was on this design in that a tab on the L...

This often times missing bracket was attached to the back of your early 1967 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the less common design.It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend into the rectangular hole to keep the bracket properly anchored to the fragile plastic. For some reason the majority of the cars built didn't get the better...

Reproduction set of 5 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design of the two and by far the superior. Replaces item # 31908Through 67-68, there were four different style brackets, you can see all four by following this link.Check out our dash bezel repair video: ...

This often times missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design.Through 67-68, there were four different style brackets, you can see all four by following this link. ...

Reproduction set of 5 XR7 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. Our improved design is better than the original in that the tab extends into the rectangular recess in the dash bezel which anchors in MUCH more securely.  Replaces item # 31907 Through 67-68, there were four different style brackets, you can see all four...

Reproduction Tail Light / Trunk Light / Courtesy Light Loom Clip for the 1967 - 1968 Mercury Cougar or Ford Mustang 

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

Sold individually Zinc (dark silver)

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...

Replacement U-nut or clip for any 1967-70 Mercury Cougar trunk lid. These slide into the bottom of the trunk lid for attaching the hinges. Correct 5/16-18 threads, 7/8" from center of hole to edge. 4 total per trunk lid, sold individually.

9" inside the arch to the end of the threads. Thread size 7/16-20, includes tall nuts as shown. Concours Grade 5 flange nuts available separately, see related items.

Sold individually, two per side, four per car required. These often get destroyed when you go to replace your door window regulator slides. Two of these are used to install the C7ZZ-6523288-A track. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size)Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video...

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

Used on the retractors.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

Reproduction tooth backed washer for the bumper bracket to frame rail bolt on the 67-68 Cougar or Mustang. 

Sold individually, phosphate & Oil (gray-black).

A nice reproduction of the standard air cleaner wing nut. This version was used on most Ford products through the 1980's.

Reproduction Wire Loom Mounting Kit for the 1968 Mercury Cougar / Ford Mustang

Master clip kit which includes following fasteners: Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorns and regulatorPassenger side apron below relayRadio cable to dashKeep in mind that there are many other fasteners on 1968 Cougars / Mustangs that are not in this kit.

Reproduction XR7 Console Fastener Kit for the 1967 and 1968 Mercury Cougar

Fits 1968 Standard or XR7

[No Description Provided]

Fits 1968 Standard or XR7

Four per car unless you have a 1968 decor or standard model that has the unique three hole armrest and then you will need six. Replaces Ford part # C7AZ-6224146. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Inner front bolt, long length to clear sound deadener. Used in conjunction with a thick, gold spacer washer.

Rear seat belt bolt, four per car used in conjunction with two red washer / spacers. 13/16" hex head, 1-1/4 inch bolt with a 3/16 inch shoulder. Can be either smooth headed or have a Heavy or Light "A". There is another version of this same bolt with a smooth head and no markings.

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

Includes battery clamp and bolts required to mount battery on tray. Please note that vinyl coating will almost always crack along edges shortly after installation.

Two of these clips per side are required to hold the interior padded pillar pads the the "A" pillars on your 1968 Cougar.Replaces Ford part number 381896-S2.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.

This clip looks just like the larger quarter extension moulding / trim moulding clip, but is smaller (as our comparison picture shows). One clip per side is used to attach the tail end (smaller end) of the moulding / trim to the extension. This unit is also almost exactly the same as the rear deck / trunk lid moulding / trim clip, but this quarter extension clip has a slightly shorter stud. Rarely will the clip you get look as good as the pictured here, usually the "finger" will be missing....

This clip looks just like the smaller rear deck / trunk lid moulding clip but is larger (as our comparison picture shows). One clip per side is used to attach the tail end (larger end) of the moulding to the extension. Rarely will the clip you get look as good as the pictured here, usually the "finger" will be missing. These clips are for the purest where originality is of the utmost importance. If originality is not an issue, you can get our excellent reproduction clip right here and...