Fasteners

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.Sold Individually.We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

Used plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Known to have been used on 1969-70 air conditioning boxes to hold a vacuum hose.Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used wire loom plastic clip for the Mercury Cougar or Ford Mustang

This is the speedometer cable clip that connects to the firewall and transmission tunnel. Replaces Ford Part # : 373829

Used Trunk Light Wire Plastic Clip for the 1967 - 1973 Mercury Cougar

Found on the lower radiator core support. 4 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part number 382350-S.

Windshield washer hose clip that holds the hose up under the cowl. Concours quality

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

Used plastic clip for the Mercury Cougar or Ford Mustang.

This small detail item is used to hold the console wiring harness to the driver side of the rear console compartment end. It clips to the top of the panel part # C7ZB-65060A74-A . Not for use with the XR7 console.Ford part number C3SB-14A163-B.

Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S

Door panel clips for the 1967 Standard or XR7. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Set includes ten rectangular clips with pop rivets and two incorrect, irregular shaped end clips (Mustang Part). These clips will fit the 68 Cougar, but are actually replicas of the clips for the 67-68 Mustang. Rather than the plastic end clips in this kit, we recommend the metal version that we sell separately. NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to...

Fits 1967 and 1968 Standard or XR7

Fits 1967 and 1968 Standard or XR7. This kit is nothing more than common door panel clips instead of the correct, unique 1967 A pillar pad clips or 68 A pillar pad clips . These can be made to 'work', but we highly recommend ordering the correct used clips.For the Correct 1967 A pillar pad clips, click here.For the Correct 1968 A pillar pad clips, click here. ...

Fits 1968 - 1973 Standard or XR7

Fits 1967 and 1968 Standard or XR7

New chrome finish screws for attaching OEM consoles. Screws fit all stock consoles 1967-73 on Mercury Cougar and Ford Mustang, most any Ford consoles actually. Phillips head oval. 1967-68 consoles use 4 attaching screws, 1969-70 consoles need 6 along the outside, 1971-73 consoles have a total of 8 screws along the outside. These are 1-1/2 inches long like the originals.

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

Sold individually Zinc Dichromate (yellow-rainbow)

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash. We think that it is Ford part number 382184.

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash.

These studs and nuts are used to repair the passenger side mounting studs. The studs need to be drilled out using a 1/4" drill bit. Once done, use a 2 part epoxy and install the stud. Make sure to avoid getting epoxy on the threads where the nut will be installed. Once dry, install the bezel into the dash and use a 3/8 # deep well socket to install the nut. CAUTION: Only tighten finger tight to avoid cracking or breaking the bezel.

There are five of these on the RH side that hold your plastic dash to the metal understructure. These also hold on the map light. Sold Individually. Ford Part #: 376642-S. Reference from mercurycougar.net: Best guys to always talk to about Cougars...will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting things...

Fine thread lock nut used in various places on old Fords, including the differential housing, 1967 disc brake assemblies, and more. Replaces Ford part # 34445-S

Fits both 8 inch and 9 inch rear ends. Phosphate and oil coated with thread sealer. These are one time only nuts. They should not be reused per Ford. Replaces Ford part #: 371518-S

This kit is a must when redoing the disc brakes on a 1968-73 Cougar. Includes new brakets (caliper stabilizers), bolts, pins, and clips and rubber dust seals. Kit includes the pair.

Replaces Ford Part #C7AZ-6243629-A. Not used on 1967-78 trunk locks.

Bulk pack of 100 oval head phillips screws for door and window crank handles.

Sold individually Zinc (dark silver)

Sold individually. Phosphate & Oil (gray-black)

These reproduction door hinge bolts are for the Mercury Cougar and Ford Mustang and fit both standard and XR7 Cougar. They are sold in a set of 24.Intended for the 1968-70 hinges that are stamped steel, and not cast iron like 1967 hinges.

Sold individually. Zinc (dark silver) finish.Little known fact: these aren't Phillips head screws, they are actually Pozi head / Pozi-Driv screws. While you can usually get a large Phillips screwdriver to work, the correct tool for these fasteners is a size 4 Pozi bit.

Reproduction Door Speaker / Courtesy Light Loom Clip for the 1967 - 1968 Mercury Cougar or Ford Mustang

# 56350-S

Bolt that attaches engine mount to block. 4 bolts per engine, used on all v8 engines Mercury Cougar and Ford Mustang 1967-68. Sold individually.Ford number 304668-S2

Holds insulation to the firewall. Sold individually, 6 per car. Replaces Ford part # C8ZZ-6501691.

Self threading white plastic. Used on front and rear valances.Sold individually.