Electrical & Lighting

Reproduction map light assembly for the Mercury Cougar XR7. It mounts under the dash pad on the passenger side (right hand) and comes with the housing, lens and wiring harness. Hardware included. *NOTE* This unit is not the same as the one that is used on the Eliminator or standard Cougar. The standard / Eliminator unit has the switch in the housing.

Used map light assembly for the Mercury Cougar XR7. This unit mounts under the dash pad on the passenger side (right hand) and comes with the housing, lens and wiring harness. After January 1970, Mercury changed the housing to plastic. We occasionally have those versions, please call for availability. This unit measures about 6-1/8" long, 1-11/16" wide and about 1-5/16" deep. *NOTE* This unit is not the same as the one that is used on the Eliminator or standard Cougar. The standard /...

Mounts under the dash pad on the passenger side. Housing has a casting number of C9WY-15A651. Assembly comes with housing, lens, and wiring harness. Used after January 1970, Mercury changed the housing to plastic, this is that version. *Note - Not the same map light assembly with switch, as found on Eliminator or Standard models with map light option.

Used white plastic instrument cluster mask for any 1970 Mercury Cougar, standard or XR7. This is the part that the clear lenses attach to.  Ford casting number D0WF-10894, Ford part number D0WY-10890-.

Mask, or shroud, that holds the clear lens for either the tachometer on an XR7, or clock or clock blank on any 1969-70 Mercury Cougar. This also fills the gap between the white plastic gauge mask and the tach or clock.  Ford casting number C9WF-10894.

Reproduction two tab power window switch for the master switch panel on the drivers door of mid 1970-72 cars. Research shows this switch was used in the master control panel on the drivers side door. With the mid to late1970-1972 and later power window systems. Compare your switch to these to insure you have the right configuration.However, for a 1969 and early 1970 master switches use a C9AZ-14529-D switch. That switch is also available, see related products tab.

Plastic power window switch holder for the drivers door. This is the master switch holder or sleeve as it is called in the master parts catalog. Used starting in mid year 1970 through 1972 on Cougars, 1971-72 Ford Mustangs, and many 1970 full sized Ford and Mercury cars. Sleeve sold as is, without internal buss bars or mounting clips. Used, often times one of the tabs is broken, still functional, may need a bit of glue or tape to keep closed. Comes with the rear cover. *Warning - Take a...

Reproduction power window motor for the driver side (left hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear pancake style motor, you can find that here.*NOTE* This is the only version of the power window motor that is available at the moment....

Used power window motor for the Driver side (left hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear pancake style motor, you can find that here. ...

Reproduction power window motor for the passenger side (right hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear pancake style motor, you can find that here. *NOTE*  This is the only version of the power window motor that is available at...

Used power window motor for the passenger side (right hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear quarter window pancake style motor, you can find that here. ...

These plastic mounting brackets came in black or gray. These kinds of minor differences can often be attributed to different suppliers. We have many that still retain the LH & RH decal for those of you trying to obtain a show car level in your restoration. The backside of this bezel will be marked LH - TOP.D0MB-15A470-B

These plastic mounting brackets came in black or gray. These kinds of minor differences can often be attributed to different suppliers. We have many that still retain the LH & RH decal for those of you trying to obtain a show car level in your restoration. The backside of this bezel will be marked RH - TOP.D0MB-15A432-B

There is not a special part number for this angled cup that was originally spot welded to the front of the headlamp switch. We offer these for use with our reproduction headlamp switch. This adapter or retainer is needed to correctly keep the headlamp switch at the correct angle to the lower metal dash. 1969-70 Mercury Cougar.

Good used part cut from the trunk of a 69-73 Mercury Cougar. This hook is concealed under the trunk mat and suspends the sequential unit over the trunk drop off area on the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

This retainer is found on the backside of the door panel and is held in place by two screws. Screws that hold plate on may be available upon request for an additional fee.

Used on the backside of all but the driver side door panel. The screws that hold this plate on may be available upon request for an additional charge.

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Flange nut for attaching any 1970 Mercury Cougar or Ford Mustang amber or red side marker lights. 8-32 threaded nut with wide flange. Two per lens, sold individually. 

[No Description Provided]

Flange nut for the 69 - 70 Convertible Windshield Mouldings. Can also be used for attaching any 1970 Mercury Cougar or Ford Mustang amber or red side marker lights. 8-32 threaded nut with wide flange. Sold individually. 

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Reproduction oil pressure remote sending unit tube assembly mounting kit.. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge. The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell...

1967-68 and 1971-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175 As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 and will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003 bulbs).  Basically good for every car from 1950 to 1990 that uses a 1156...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Plasma LED 1157 replacement bulb in YELLOW for your parking / running lights. Much brighter than stock, more responsive, and less power draw. We won't go so far as to call these little guys AMBER, but they're definitely yellow. Good for your 67 - 73 Cougar, Mustang or anything else that takes a dual-filament 1157 bulb for marker lights or turn signals. Specs: Power: 7.5...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1157 WHITE LED Plasma stop lamp / turn signal light bulb for your 67 - 73 Cougar, Mustang or anything else you might have that takes a white 1157 bulb. Please note that these bulbs are ground sensitive. Did you know that white (clear) 1157 bulbs fit a ton of other cars and trailers from the 50's clear through the 90's and beyond that used the...

This plug will work on your 69 - 73 Standard or XR7 as well as the 69 - 73 Mustang. This plug housing is used to connect the under dash main loom to the gauge cluster.

This used plug end will work on your 69 - 70 Standard or XR7 as well as the 69 - 70 Mustang. This plug housing is used to connect the under dash main loom to the gauge cluster.*Does not include wires

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

Plastic plug end used to mate to the individual switches on a 1969.

Power lead from starter solenoid to circuit breaker for any of the following: power windows, convertible top, automatic seat back release, headed back light or rear defog (1971-73), or power seat.Replaces Ford Part #: C9WB-14678-B

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction master power window switch that goes along with the power window conversion kits. Keep in mind we will buy your old usable factory parts. You might be surprised what those left over clips and wiring harnesses are worth!  Installing this master switch allows you to keep the original look of the crank handles, but allows the driver to control all four windows. All wiring and connectors are included.  ...

This gear was used on Cougars starting in 1969 and then Mustang in 1971. Fits pretty much every (common) Ford power window motor except for the unique "pancake" style motors found with the 1/4 windows on the Cougar and Mustang. Includes metal plate as shown. Replaces Ford part # D0AZ-62234A24. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969...

Ford part number C9WY-10K843-C Whereas the engineering number printed on the backside of this PCB is the same red vs blue there is a distinct difference. Many people get confused with the numbers printed or cast into parts thinking that that is a part number when really it is a casting number or engineering number and may or may not resemble the actual part number listed in the MPC (Master Parts Catalog). 1969 Standard Cougars used the blue PCB (printed circuit board) up until 2/17/69 and...

Good used PCB that has no burns, corrosion or separating areas. The red PCB (printed circuit board) was used in the latter part of 1969 (from 2/17/69 on) and all of 1970. In 1969 if you had a white plug connected to the PCB it used a red PCB, if you had a black plug the blue PCB was used. Check out the video below on our new gauge tester: ...

Ford part number C9WY-10K843-D Finally! A made in the USA reproduction printed circuit board for your late built 1969 - 1970 Standard Cougar. This is a spot-on, class "A", no excuses reproduction that will give you decades of reliable service. This part exceeds the quality of the originals in that it is made from thicker materials, is bonded better, is more flexible and does not contain formaldehyde as did the originals. This is only for use on the late 1969 Standard white wiring harness...

Ford part number C9WY-10K843-D Finally! A made in the USA reproduction printed circuit board for your late built 1969 XR7 or Eliminator (built after 2/17/69) and all 1970 XR7 and 1970 Eliminator. This is a spot-on, class "A", no excuses reproduction that will give you decades of reliable service. This part exceeds the quality of the originals in that it is made from thicker materials, is bonded better, is more flexible and does not contain formaldehyde as did the originals. This is only for...

This plastic plate / bracket is installed between dimmer switch and the floor of your 67 - 73 Cougar to provide a bit or protection for the wiring.

Used cast dual sheave alternator pulley. Casting number C9AF-10A352-C, we believe that these originally had a zinc dichromate finish. Called out for use on various 1969-70 Mercury Cougar and Ford Mustang with a need for a dual sheave alternator pulley. Just a tiny bit smaller than 2-3/4 inches in diameter. *Note - this is a cast pulley instead of the common stamped steel single sheave version. Ford part # C9AF-10A352-C.

This Autolite capacitor is stamped with part number C6OA-18832-A. It attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. All Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory. Starting in 1972 there is a Motorcraft version which has a...

Reproduction black extruded plastic shield, or rain gutter for the voltage regulator on any 1969-70 Mercury Cougar or Ford Mustang. Replaces Ford part number C9ZZ-10A506-A.

Used black extruded plastic shield, or rain gutter for the voltage regulator on any 1969-70 Mercury Cougar or Ford Mustang. Ford part number C9ZZ-10A506-A.