Exterior Lights

Used and tested original sequential unit for the 1969 - EARLY 1970 Mercury Cougar. This unit will come with a 90 day warranty. Keep in mind that if you want to use the brighter LED's on your car, this original sequential system will not work. If you want to change over to LED, you will need the updated sequential unit which you can find here. If you need the sequential enclosure box, you find our used boxes here. ...

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps. Even the original LH decals will be in place! These are good quality parts ready to install on your Cougar. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side. ...

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps. Could have decals missing, and will have minor pitting. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side.

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps. Even the original RH decals will be in place! These are good quality parts ready to install on your Cougar. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side. ...

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps.Could have decals missing, and will have minor pitting. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side.

Nice reproduction rear body side reflector as found on 1968 Mercury Cougars. Used on Montego / Cyclone / Cougar for the 1968 model year. Great reproduction, but without the 'FoMoCo' marking like on our concours version. This reflector comes with the rubber gasket and attaching nuts. Very nice and at an attractive price. You'll also want these rubber protectors for the trunk.Replaces Ford part # C8GY-13380-A. *Note - Also fits 1968 Mustang after Feb 15, 1968. *Trivia - 1968 Mustangs did not...

Perfect in every detail down to the FoMoCo logo. Used on the 1968 Montego / Cyclone / Cougar for the 1968 model year. Great reproduction made from the original Ford tooling. This is the Concours version with FoMoCo marking on the lens. Listing is for the reflector only, does not come with gasket or hardware. Also, don't forget the rubber protectors that slip over the pointy studs inside the trunk. Replaces Ford part #C8GY-13380. ...

This pair of die-cast chrome front side marker bezels are sold as pictured with no socket, lens, lens gasket, bulb, mounting hardware or fender to body gasket, but all of these items are available here on our website. These side fender lights resemble "fine jewelry" when mounted on your freshly painted fenders... The fit and finish are very good but the hole in which the socket mounts is slightly larger than original which works well with our reproduction socket assemblies. If you are using...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Reproduction side marker light socket with harness set. For all 1968 Mercury Cougar and Mercury Montego and Cyclone. This listing is for a pair of wiring harnesses with light sockets. The original sockets were a snug fit in the fender light housings. These sockets are a slightly larger diameter than original and work well with the reproduction housings, but you may need to enlarge the hole if you're using your original housings. These wiring harnesses look real sharp with our reproduction...

The D0WY-15A434-LSM LED Side Marker Light Adapter kit is required when the C9WY-13A366-AL or the TS-400 Sequential controller is installed with LED front turn signal and LED side marker bulbs on most 1970 and up Ford vehicles. An adapter is required for each side marker light (4 total). This adapter solves the problem where the side marker voltage feeds back through the front turn signal bulb when the running lights or headlights are turned on. When this happens all the rear bulbs may flash...

The D1WY-15A434-LSM LED Side Marker Light Adapter kit is required when the C9WY-13A366-AL or the TS-400 Sequential controller is installed with LED front turn signal and rear LED side marker bulbs on 1971 Cougars and other Ford vehicles with two rear side marker lights. An adapter is required for each rear side marker light (2 total). This adapter solves the problem where the side marker voltage feeds back through the front turn signal bulb when the running lights or headlights are turned on....

Coming from Western parts cars these brackets are unusually nice in comparison to what you will find in other regions. For and extra $1.50 we can include the mounting nuts. Right is the same as left, two brackets required per car, sold individually.

Good used light with no pits or scrapes. Does not include lens or pigtail with socket, does include mounting bracket with two nuts. The chrome body carries a C8GB-15A428-B engineering number and the pigtail has a C8WB-15A442-A engineering number imprinted on the wire. We usually only have one or two in stock of this caliber so do not be surprised when you try to place this in your cart and it shows 0 quantity. Even though this is the best we will ever have to offer off of a Western parts car...

This grade "B" light bezel will have minor blemishes in the chrome as shown. Good part for a driver as it will not have deep pits. Does not include pigtail or lens. Left is the same as right. To remove pigtail from your existing light wrap socket in cloth to protect and grip firmly with a pair of pliers, rock back and forth while pulling and the plug and socket assembly should come right out from the back side. Replaces Ford part # C8WY-15A201-C.

Ford never offered this socket / plug assembly on its own but we do from time to time get one that has a clean socket and no cuts in the wiring. You can often just twist and pull (after the bulb has been removed) and it will come right out of the chrome housing. The Ford engineering number imprinted on the wire is C8WB-15A442-A.

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

Replaces stop lamp relay on 1967 Cougars built before 1-3-67. No wiring modifications needed, just plug it in in place of your old mechanical relay in the trunk. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the...

New Old Stock relay. Known as the "K-11" relay in the Ford Service manual. This relay was only used in production prior to 1-3-67. It provides a low current circuit through the relay solenoid and the stop lamp switch and a separate circuit through the relay points to handle the higher current load of the stop lamps. Again, this unit was only used in early 1967 Mercury Cougars. This early brake light relay is unique to Cougars built prior to 1-3-67. Unlike the later built Cougars, it...

Known as the "K-11" relay in the Ford Service manual. This relay was only used in production prior to 1-3-67. It provides a low current circuit through the relay solenoid and the stop lamp switch and a separate circuit through the relay points to handle the higher current load of the stop lamps. Again, this unit was only used in early 1967 Mercury Cougars. This early brake light relay is unique to Cougars built prior to 1-3-67. Unlike the later built Cougars, it mounts next to the sequential...

Used stud and nut for inserting and attaching to used or reproduction side marker lenses. Red or amber lenses.

Reproduction mounting studs for the side marker light lenses on 1970 Cougars and Mustangs. 2 required per light, 8 per car.Sold as a pair.

Reproduction studs and nuts for the taillight to body on the 1969 - 1970 Mercury Cougar 

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. The relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to illuminate the directional arrows on the dash and does...

Replacement turnsignal switch for all 1968 Mercury Cougar and Ford Mustang with fixed (non-tilt) steering columns. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. The relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to...

NOTE!!!! This offshore switch is assembled with plated steel rivet contacts as opposed to brass rivet contacts like original. Whereas the Torino or Mustang do fine with 2 incandescent rear bulbs the Cougars with 6 bulbs put too much load on the switch and they fail. The only way these switches will hold up in a Cougar is if you convert to LED. We are hoping the supplier will take our advice and correct this problem but until such time we cannot warranty this product. Don Rush 9-11-2017 1970-72...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This turn signal switch for the 1967 Cougar equipped with the tilt / tilt away steering column is made using the original tooling acquired from the original manufacture of this part that Ford purchased these switches from when they were originally installed new in the Cougar. If you have replaced your sequential unit in the trunk with one of our new solid state sequential...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. For 1968, the relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to illuminate the directional arrows on the dash...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This switch also fits the 1970-1972...

Good used grade "A" taillight bezel for the 67-68 Mercury Cougar. This grade "A" unit will not have any pits, bends on the ribs and the chrome will have good luster. When you mention it in the comments section, we will try to pick out examples that still have the detail paint in tact. This no excuses bezel will look great on your high quality unrestored driver. Right and left are interchangeable. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

Good used driver quality grade "B" bezel with no bends, cracks or deep pits. Chrome will have a decent luster (not perfect), but the paint will need to be redone. If you want show quality then the only way you will be happy is to buy our rechromed bezels. Right and left are interchangeable. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

These never came on a Cougar; these are reproduction 1967 Shelby tail light lens bezels. The reason we list them is that over the years many of our customers have been cutting out their vertical ribs on the 1967-68 Cougar tail light bezels to completely expose the tail lens.  These Shelby bezels offer a direct replacement clean restomod look without all the hassle of cutting up your valuable Cougar parts. As the close up will show there are slight machining marks so you may want to polish...

Beautiful show quality triple-plated chrome taillight grilles / bezels for your '67-8 Cougar! Better than new. Sold as a pair. Bare chrome, so you will have to do the black detail paint yourself (see tips below). Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior...

Sold individually, right is the same as left. Needs no repaint in the reflective area and will actually be in much better condition than what is pictured. Seals will need replaced as they are original. Comes with original mounting studs. Great for Shelby or Eleanor clones. Why buy $100 ABS plastic reproductions when you can have original FoMoCo? *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned...

The only difference between grade "A" and grade "B" on this part is the reflective finish on this grade "B" part needs to be redone. There is a spray paint specifically for this application sold by Krylon and others. The pair you get will actually look much better than what is pictured here. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Good used pair of taillights that includes two average grade "B" bezels and two used grade "B" lenses with backing plates. No obvious cracks in the lenses but there will be stress cracks that will only be found under close inspection. The bezels will have good chrome with no obvious defects but the paint will need attention. This is a good saving over buying the four or six parts individually. Don't forget to pick up a set of gaskets for the lenses as they always are needed after 40 plus...

Good used socket ready to plug into your 67-68 tail harness and snap into your taillight housing. Also used on 1967 Shelby Mustang. Sold individually, six required per car.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Sold as a pair. New to the market as of 2009. Take a look at our many pictures below of these bezels installed with original backing plates and lenses.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject.Click...

Used grade "A" taillight wiring harness for the Mercury Cougar. No cuts or splices, perfect plugs with no visible corrosion.  This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-B before 2/1/71 and D1WY-14405-D from 2/1/71 - 5/15/71).  If you are in need of one of these early harnesses, please contact us so we can discuss what you need.Ford part # D2WY-14405-A.*NOTE* Need help diagnosing a Cougar...

This is a restored 1973 driver side taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. ...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.

This is a restored 1973 passenger side taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. ...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.

1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a red 4 pin plug, that is designated D-3 in the wiring diagram. This plug plugs into the sequential turn signal relay in the trunk. We are offering all of the various plugs for repairs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 4 pin plug, that is designated D-4 in the wiring diagram. This plug plugs into the sequential turn signal relay in the trunk. We are offering all of the various plugs for repairs.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a white 4 pin plug, that is designated D-4 in the wiring diagram. This plug plugs into the sequential turn signal relay in the trunk. We are offering all of the various plugs for repairs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...