Sequential Turn Signal Parts

Great Reproduction of an Often Broken Part. This part fits on the bottom of the steering wheel and must be in place to cancel your turn signal on tilt column cars. Used on all Ford products with a tilt column 1967-69. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

Factory original turn signal canceling cam. Originals were molded in white, reproductions are molded in black. Repros also available from us. Without this part that self attaches to the back of your factory steering wheel, you will be turning off your blinkers manually. Click up, click down... *NOTE* We have no good reason to encourage you to purchase this hard to find original over the reproduction, unless you just gotta have it. **NOTE** Need help diagnosing a Cougar turn signal problem?...

Used in 1968 Mercury Cougars for the sequential motor, located under the dash on a panel next to the fuse block.15amp circuit breaker, not clearly identifiable in the Ford MPC. It is 1.07" x 0.40" and has a single green dot. Box is marked Tung Sol, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

Used in 1967 Mercury Cougars for the stop lamp switch, located under the dash on a panel next to the fuse block.15amp circuit breaker, not clearly identifiable in the Ford MPC. It is 1.07" x 0.40". Box is marked 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. The MPC shows this circuit breaker was also used on 1965-66 Continental convertible and 1965 Thunderbird convertible. These are tested and guaranteed to work.*NOTE* Need help diagnosing a Cougar turn signal...

Used in 1969-70 Mercury Cougars for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.07" x 0.40" and has a single green dot. Box is marked Tung Sol, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Also fits 1969 and newer Mercury full size, 1970-71 CycloneFord part number C9MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the...

Used in 1971-73 Mercury Cougars and Ford Mustang for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.25" x 13/16" and has a single green dot. Box is marked FASCO, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Ford part number D1MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

3/4" wide and 60' long. This tape resembles the tape you would find on bicycle handle bars or a hockey stick but is in fact different. The taillight harness uses this type of tape as well as portions of the under dash harness. Not used in modern applications and getting rather hard to find these days.NOTE: This is FRICTION tape not adhesive tape. It is coated with rubber and relies on friction with itself to wrap wires. It does not stick to the wires. This was one of the first types of...

Reproduction complete electronic sequential system for the Ford Thunderbird produced after Jan. 16th, 1967. This unit does not come with the stop lamp relay and is a special order item only.*NOTE* Need help diagnosing a turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Reproduction complete electronic sequential system for the Ford Thunderbird produced before Jan. 16, 1967. This unit includes the stop lamp relay. *NOTE* Need help diagnosing a turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

New emergency flasher can for all 1969-73 Mercury Cougars. Not to be confused with the turn signal flasher canister, those are rated differently. 

This two part black box is what encapsulates your sequential unit for all years 1969-1973. This of course will work with our reproduction sequential unit as well. This box was designed hang from a hook that is welded to the trunk floor just behind the driver side wheel well. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Direct plug in solid state replacement, no modifications needed. We highly suggest considering not purchasing this unit and invest in the all inclusive unit. All of the original sequential components in the trunk of your Cougar are mechanical and will in time fail. It is much more cost efficient to buy the all inclusive unit than to purchase them one by one as they fail. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the...

No modifications needed, just open the trunk and plug the unit into your original wiring! We highly suggest considering not purchasing this unit and invest in the all inclusive unit. All of the original sequential components in the trunk of your Cougar are mechanical and will in time fail. It is much more cost efficient to buy the all inclusive unit than to purchase them one by one as they fail. This reproduction is an exact replacement for this original unit. This updated relay will...

Good reproduction of a knob that is always broken off. Made from milled aluminum rather than plastic as the originals were made. This makes it so it is not as susceptible to breaking off. Unique to Cougars with tilt columns in 1968 - 1969. Replaces Ford part number C8MY-17513-C. This part also fits the 68-69 Mustang, Lincoln, Marquis, Thunderbird and other like models with an adjustable steering column.

Tested and working sequential turn signal motor for the mid 1967 and all 1968 Mercury Cougars. This is the dual plug motor compared to the single plug 1967 turn signal relay. New in box (Motorcraft box) unit that is tested and will be functional. Trouble shooting these systems takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. We suggest you consider our all inclusive solid state unit that replaces all the units in the trunk if you have...

Tested, cleaned and working sequential turn signal motor for the mid 1967 and all 1968 Mercury Cougars. This is the dual plug motor compared to the single plug 1967 turn signal relay. Clean used unit that is tested and will be functional. This unit will not be rusty or have internal water damage, may have minor repairs, no cut wires. Trouble shooting these systems takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. We suggest you consider our...

This rubber board is used to mount your sequential unit behind the driver side wheel well. If your Cougar was built before 1-2-67, you will need this large board. This rubber mounting board also works with our reproduction solid state sequential unit. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is...

This rubber board is used to mount your sequential unit behind the driver side wheel well. This version is only for the late 1967 (built after 1-3-67) and 1968. If your Cougar was built before 1-3-67, you will need the smaller version. This rubber mounting board also works with our reproduction solid state sequential unit. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and...

Good used part cut from the trunk of a 67 Mercury Cougar. This hook is concealed under the trunk mat and suspends the sequential unit over the trunk drop off area on the driver side. Unlike 1968 models, there are two of these required per car and we sell them individually. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Good used part cut from the trunk of a 1968 Mercury Cougar. This hook is concealed under the trunk mat and suspends the sequential unit over the trunk drop off area on the driver side. One piece plate for 1968, The 1967 Cougars had two individual hooks welded to the edge of the trunk floor.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Good used part cut from the trunk of a 69-73 Mercury Cougar. This hook is concealed under the trunk mat and suspends the sequential unit over the trunk drop off area on the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1076 WHITE Led Plasma back up light bulb for your 67-68 or 71-73 Cougar, Mustang or anything else you might have that takes an 1076 bulb. Please note that these bulbs are ground sensitive. Specs: Power: 7.5 Watts Brightness: 300 Lumens Total life expectancy: 30,000 hours 2" Tall (1 3/8" extends out of the socket) Comparison image - Click to view full-size: Check...

1967-68 and 1971-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175 As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 and will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003 bulbs).  Basically good for every car from 1950 to 1990 that uses a 1156...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Plasma LED 1157 replacement bulb in YELLOW for your parking / running lights. Much brighter than stock, more responsive, and less power draw. We won't go so far as to call these little guys AMBER, but they're definitely yellow. Good for your 67 - 73 Cougar, Mustang or anything else that takes a dual-filament 1157 bulb for marker lights or turn signals. Specs: Power: 7.5...

The function of this relay is to make only the center lights on each side illuminate when you activate the emergency warning flashers. Failure of this relay causes only the center sequential light to flash when using the turn signals. Trouble shooting these systems is takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. This unit is built into the 1967-68 Solid State Sequential Upgrade we sell so it is not needed if you are buying the all...

This is known as the "K6" relay in the Ford service manual. The function of this relay is to open the circuit between the two instrument panel turn indicator lamps during normal turn signal operation. During emergency flasher operation, the relay points are closed (normal position) and the two instrument panel indicator lamps flash at the same time. Ford Part # C7WY-10B926-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on...

This is known as the "K6" relay in the Ford service manual, part number C7WB-10C838-C or C7WY-10B926-B. The function of this relay is to open the circuit between the two instrument panel turn indicator lamps on 1967-68 Mercury Cougar during normal turn signal operation. During emergency flasher operation, the relay points are closed (normal position) and the two instrument panel indicator lamps flash at the same time. These relays are tested and working units. UNDER DASH RELAY *NOTE* This...

Referred to as the "K10" relay in the Ford Service manual. The emergency relay, when energized, maintains through circuits from the motor and cam assembly to the rear lamps. During emergency flasher operation, this relay opens the circuits (normal position) to the inner and outer rear signal lamps. Thus, only the center rear lamps operate when the emergency flasher system is functioning. This unit was originally mounted to the underside of the black cardboard trunk filler board on the driver...

Used sequential unit (found in trunk) relay for all 1970-73 Mercury Cougar, 4 total per car. Additionally this relay was used as a horn relay for 1965 Ford Mustang with generators; 1966 Lincoln Continental relay for moveable steering columns; 1969 and later Ford and Mercury full sized with speed control relay and power back window relay (on station wagons). Ford Engineering # C4AZ-13853-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

This is referred to as the "K5" relay in the Ford service manual. This relay causes the flashing action of the 1968 Mercury Cougar instrument panel indicator lights. The number stamped on this relay is C8WB-13A366-A or C8WB-13A366-C, the Ford part number is C8WY-13A366-A or C8WY-13A366-C. Stay tuned for an upcoming electronic version of the 1968 K7 relay.*Caution - Do not use the 1967 relay in place of the 1968 relay, smoke and fireworks will be the result.

This is referred to as the "K5" relay in the 1968 Ford service manual. (In 1967 it was called the K7). This relay causes the flashing action of the 1968 Mercury Cougar instrument panel indicator lights and almost never works... The number stamped on this relay is C8WB-13A366-A or C8WB-13A366-C, the Ford part number is C8WY-13A366-A or C8WY-13A366-C. We suggest replacing this unit with our new and improved solid state unit.*Caution - Do not use the 1967 relay in place of the 1968 relay, smoke...

This is referred to as the "K7" relay in the Ford service manual. This relay causes the flashing action of the 1967 Mercury Cougar instrument panel indicator lights. The number stamped on this relay is C7WB-13A366-A, the Ford part number is C7WY-13A366-C. We have these relays tested and ready to ship. A quick bench testing: There needs to be continuity between the 'H' post and both 'B' and 'S' (separately). We test them with 12v to the 'H' post and the base grounded. 12volts should be read on...

At last, there's a solution to a problem that almost all early Cougars suffer from. If the turn signal indicators in your dash only blink once, and then pulsate slowly without going out, you need this new electronic relay. It's a direct plug-and-play replacement, and it will give your indicators a nice on-off flash, complete with a mechanical click sound, all in time with your turn signals. We're excited about this simple fix; it's great to see and hear the indicators working properly. The...

At last, there's a solution to a problem that almost all early Cougars suffer from. If the turn signal indicators in your dash only blink once, and then pulsate slowly without going out, you need this new electronic relay. It's a direct plug-and-play replacement, and it will give your indicators a nice on-off flash, complete with a mechanical click sound, all in time with your turn signals. We're excited about this simple fix, it's great to see and hear the indicators working properly. The...

This unit is known as the "K5" relay in the service manual and is stamped with C7WB-13A366-B. The turn signal indicator relay switches the indicator light circuit so that the left indicator lamp on the instrument panel flashes for left turns and the right lamp flashes for right turns. Application is 1967 Mercury Cougar. No guarantee that replacing it with our used unit will actually make your dash lights consistently blink more than two or three times before going into a "pulsate mode" (if...

1968 Mercury Cougar K-8 and K-9 turn signal relay assembly. K-8 for the passenger side, K-9 for the driver side turn signals. Also is integral to the brake light circuit. Clean used unit that is tested and will be functional. This unit will not be rusty, have internal water damage, May have minor repairs, no cut wires. Trouble shooting these systems is takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. When these relays are not energized,...

1967 Mercury Cougar K-8 and K-9 turn signal relay assembly. K-8 for the passenger side, K-9 for the driver side turn signals. Also is integral to the brake light circuit. Clean used unit that is tested and will be functional. This unit will not be rusty, will not have internal water damage, may have minor repairs and no cut wires. Trouble shooting these systems is takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. Great for the...

1968 Mercury Cougar K-8 and K-9 turn signal relay assembly. K-8 for the passenger side, K-9 for the driver side turn signals. Also is integral to the brake light circuit. Clean used unit that is tested and will be functional. This unit will not be rusty, have internal water damage, May have minor repairs, no cut wires. Trouble shooting these systems is takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. When these relays are not energized,...

These clever kits allow you to replace the broken cam without having to swap the whole assembly. Mounting hardware is included. Works on 67-72 fixed columns and 67-73 tilt columns. Replaces Ford Part # C7SZ-13318-B and D0AZ-13318-A. Watch Install Video

This sequential flasher is an electronic flasher kit to provide sequential tail lights to any automobile with two or three tail lights per side, and are using Plasma LED's. Parts included in this kit are: Sequential Control Unit with pre-soldered connectors, electronic flasher can typical application schematic, and trouble shooting guide. We have had everyone from Truckers wanting sequential lights on their mud flaps to 1966 Dodge Charger owners purchase this easy to install trouble free kit....

This is a complete 1967 sequential core unit as taken from the trunk of a 1967 Cougar built before 1-3-67. It most likely will not work and has not been tested. This is for the person who really strives to keep his car original and has a good understanding of electronics. This unit will not have cut wires or water damage. We highly suggest using our modern solid state unit as these were never designed to last 40 years and were often problematic from their inception. *NOTE* Need help diagnosing...

This is a complete 1967 sequential core unit as taken from the trunk of a 1967 Cougar built after 1-3-67. It most likely will not work and has not been tested. This is for the person who really strives to keep his car original and has a good understanding of electronics. This unit will not have cut wires or water damage. We highly suggest using our modern solid state unit as these were never designed to last 40 years and were often problematic from their inception. *NOTE* Need help diagnosing...

This is a complete 1968 sequential core unit as taken from the trunk of a 1968 Cougar. It most likely will not work and has not been tested. This is for the person who really strives to keep his car original and has a good understanding of electronics. This unit will not have cut wires or water damage. We highly suggest using our modern solid state unit as these were never designed to last 40 years and were often problematic from their inception. *NOTE* Need help diagnosing a Cougar turn...