All Products

Used A/C suction service valve for 1969 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch 'O'-ring fitting for suction hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Used A/C suction service valve for 1970-73 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch 'O'-ring fitting for suction hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.

Used servo cover from a 1967-68 Ford C-4 transmission. This cover has the big A cast into it, which designates it as an "A" servo. Cover only, marked C6AP-7D027-C.

Correct shackle for all 1967 through 1973 Cougars, except those manufactured between 10/70 and 9/71. Measures 3-1/2 inches from center to center. Bushing dimensions: Length 1 1/8", outside diameter 1" (shaft piece) - 1 1/4" (end piece), hole diameter 1/2" Sold individually, two required per car. Replaces Ford 5630 shackle kits that include bushings C4GY-5781-A and D4DZ-5781-A.

Correct length (3-1/2 inches from center to center) and construction shackle for all 1967 through 1973 Cougars, except those manufactured between 10/70 and 9/71. Ships complete - 2 piece shackle with original nuts. New bushings not included, but recommended. Sold individually, but two are required for the rear suspension. Replaces Ford 5630 shackle kits that include bushings C4GY-5781-A and D4DZ-5781-A.

Correct length and construction shackle for all 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Ships complete - 2 piece shackle with original nuts. New bushings not included, but recommended. Sold individually, but two are required for the rear suspension. These also fit 1970 - 1972 Ford Mustangs. Replaces Ford 5630 shackle kits that include bushings C6DZ-5781-A.

Complete Set of 1" leaf spring poly bushings for the rear eye of the spring shackle. Sold in packages of 8, 4 per side. Correct size for the 1967 - 1973 Mercury Cougar except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: D4DZ-5781-A. May be dropshipped. *except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71.

Set of 1" leaf spring poly bushings for the rear eye of the spring. Sold in packages of 8, 4 per side. Correct shackle bushings for all 1971 through 1972 Cougars manufactured between 10/70 and 9/71. 1 5/16" OD.5" ID1.25" insert depth. .25" lip Replaces Ford Part #: C6ZZ-5781-B & C6DZ-5781-A. May be Dropshipped

Complete Set of 1" leaf spring rubber bushings for the rear eye of the spring shackle. Sold in packages of 8, 4 per side. Correct size for the 1967 - 1973 Mercury Cougar except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: D4DZ-5781-A. *except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71.

Used shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. We do not have the spring clip available. Ford part number of C8AZ-2478-A. 

Used lower shaft fixed steering column found from 1968-69 Mercury Cougar or Ford Mustang. This is the portion that mates with the upper shaft that bolts to the steering coupler. 1968-69 lower shafts are 15-1/2 inches in overall length. They also have a lower flange with flat sides. Other Ford fixed lower shafts can be used, in most cases the sheer pins are already broken. Just slide the shafts together for the desired length. WCCC no longer has an in-house service for tilt and tilt-tilt away...

Shaft or rod for the heater damper door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C7ZZ-19C774-B.*Note will not work in 1969-73 A/C boxes.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with C-4, automatic transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block Cougars with automatic transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with manual transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always superior.Ford...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any factory Cougar V8 engine. 289, 302, 390, or 428CJ Cougars with manual transmissions.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any 1969 Mercury Cougar unless equipped with factory speed control. *Note - not for use with 1969 factory cruise control.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any 1970 Mercury Cougar.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with all 1971 Mercury Cougars and 1972 Cougar up until 6/19/1972. Accelerator cable attaches with a clevis pin.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with 1972 Mercury Cougars built after 6/19/1972, and all 1973 Cougars. Has a hole for either a green or blue plastic bushing on the cable end.

Shaft assembly for driver side hideaway headlamps for any 1969 Mercury Cougar. Complete with rag joint and nut. Sold individually, one per side. These have become side specific due to time, and stress on those rag joints.

New Old Stock Shaft assembly for hideaway headlamps for any 1969 or 1970 Mercury Cougar. Complete with rag joint and nut. Ford part number C9WY-13B014-A.

C9WY-13B014-A Shaft assembly for passenger side hideaway headlamps for any 1969 Mercury Cougar. Complete with rag joint and nut. Sold individually, one per side. These have become side specific due to time, and stress on those rag joints.

UPDATE 11-19-20: We still do not have the shaft seal dialed in but we are offering this kit with a proven substitute seal until further notice. This kit will recondition most FoMoCo headlamp actuators built from 1967 into the 70's on most any Thunderbird, Torino, Lincoln, Cyclone or Marquis. The kit will service two actuators even though many cars only come with one center mounted unit. If your actuator holds vacuum on the bottom port but does not hold vacuum (or pressure) on the top port then...

Plastic shield, for protecting the power window door switches on some 1969-1970 Mercury Cougars. We don't see them on every car with power windows, but they do exist, and fit either driver or passenger side doors. Limited stock. Replaces Ford part number C9WB-14A099-A and D0WB-14A099-A.

Used windshield wiper motor cover or shield as Ford called it. Very prone to cracking and 'chalky' from age or UV light. We are not going to lie, most of these will have paint over spray or a slight amount of chalkiness. We haven't found a Ford part number other than the basic number of 17C441 which is labeled as "Shield - (Windshield Wiper Motor - Water)" as found in the Mercury MPC.

This arm is attached to your automatic transmission floor shifter (see picture at left). Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for C-4 and C-6 transmissions. Ford part number C7ZZ-7302-A. ...

This arm is attached to your automatic transmission floor shifter (see picture at left). Fits all 1969-70 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for FMX and C-6 transmissions. Ford part number C9ZZ-7302-A. This part may have the course threads or fine threads. Normally this item ships with the course threads. We also stock the 1971-73 version that has a captured stud for...

This arm is attached to your automatic transmission floor shifter. Fits all 1969-73 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. This used part will come with a captured lower stud for attaching the shift rod as shown. Correct for FMX and C-6 transmissions. This version is found on 1972-73 cars, it has the captured lower stud for mounting the automatic shift rod to the transmission. Ford part number D1ZZ-7302-A. Check out our video on rebuilding...

You will not need to make any modifications to run this leather unit in place of your original rubber boot used on three and four speed manual transmissions.

You will not need to make any modifications to run this leather unit in place of your original rubber boot used on three and four speed manual transmissions.

This 4 Speed Lower Shift Boot attaches to the bottom side of your shifter to protect it from water and dirt. Fits the 67 and the 68 with 289 or 302 engines only Replaces Ford part #: C6ZZ-7138-C.

This bezel was never offered from the factory on a Cougar, but is a very attractive part for those with a manual transmission and no console. This unit works with three or four speed manual transmission and with a rubber or leather shift boot.

Original style, factory 3 speed lower shift boot.Replaces Ford part #: C6ZZ-7138-B

Original style, factory 4 speed lower shift boot.

Get a grip with this reproduction Hurst T handle, or shifter handle. This 1971 model is without the set-screw as found on the 1970 shifter handle. Ford part # D1OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Shift kit for the C4 transmission valve body for all 1967-67 Mercury Cougar and 1967-69 Ford and Mustang. This is a standard shift rebuilding kit for your stock valve body.

Shift kit for the C6 transmission valve body for all 1967-73 and 1967-73 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.

Shift kit for the FMX transmission valve body for all 1969-72 and 1969-72 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.* Note - 1973 has a different shift kit, see related items.

This one might cost a couple dollars more than others you may have seen but it is the best in my opinion. This is correct for a standard Cougar, XR7 had a woodgrained finish. Check out our video on rebuilding your shifter below: ...

Very hard to find 69 - 70 Shelby / 67 - 69 Cougar 4 speed shifter knob. Almost a year in development was spent to get as close as possible to original N.O.S. sample. These very rarely come up for sale used and when they do, they are expensive. Knob insert is made of metal just like original not brass. Knob also has the correct groove in middle of body like 69 version and not the earlier version which does not. Not technically correct for a 67-8 Cougar, as the 67-8 does not have the groove in...

Attractive knob used on later 68 through 69 non XR7 Cougars. I recently installed one of these on my own cars and had the face fall off the main body the first time I used it. I glued it back on and have had no problems since. Replaces Ford Part #: C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

For those who want to want a correct looking interior in conjunction with their modern transmission. Check out our video on rebuilding your shifter below: ...

For those who want to want a correct looking interior in conjunction with their modern transmission. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for some 1970 Mercury Cougar or Ford Mustang, and all 1971-73 Cougar and Mustangs, with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1969 and most 1970 Mercury Cougar or Ford Mustang with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-A. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1967-68 Mercury Cougar or Ford Mustang with consoles. This console lever is unique to console equipped cars, it has a tab with a hole in it for accepting the shift indicator indicator rod. We sell these bare for those car owners that have pitted shifter levers. Ford part number C7ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...