All Products

C7ZZ-7515-D Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12 inches long. Cougar 1967 through 2-15-1968. 390-4V engines only, XR7, XR7-G. Mustang 1967 through 2-15-1968. 390-4V only, GT. Mustang 1967. K code 289 HiPo 4 speed only. GT

C8AZ-7515-A Manual transmission clutch fork - 4 speed, stick shift transmissions. Fork measures 12-7/16 inches long. Alternate number C8AA-7541-A. Cougar 1971, 429 Cobra Jet engines. Mustang 1971, 429 Cobra Jet engines. Galaxie / LTD, 1968 - 1969, 428 / 429 Passenger car engines. 500, XL, Custom. *Trivia - This fork originally had a yellow paint mark for identification purposes.

C9ZZ-7519-B Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

Unique to the 1973 Mercury Cougar and Ford Mustang with 351 engines. This is a two piece ducting that connects to the air cleaner snorkel with a flex tube. Hard to find in this condition, the lower section has a metal tab that gets corrosion from the battery. Sold as a two piece set, Grade A will have undamaged mounting tabs. The Ford MPC specifies that this is only for the 351-2V and 351-CJ (351-4V) engines.Ford part number D3ZF-9A624-A.

Unique to the 1973 Mercury Cougar and Ford Mustang with 351 engines. This is a two piece ducting that connects to the air cleaner snorkel with a flex tube. The grade B lower section will have a broken, or damaged metal tab from battery corrosion. Sold as a two piece set, Grade A will have undamaged mounting tabs. The Ford MPC specifies that this is only for the 351-2V and 351-CJ (351-4V) engines.Replaces Ford part number D3ZF-9A624-A.

Good used upper collar for the tilt column on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This is an original NOS hot idle compensator for Mercury Cougar or Ford Mustang models with V-8 engine and factory A/C. It is installed in the middle of the hose that connects the PCV valve to the rear of the carburetor spacer. It opens when it reaches a certain temperature which makes the engine run faster when at idle and the A/C is on thereby making the engine run more efficiently. This is an original Ford part that came on air conditioned models from the factory. It was manufactured by...

Used Grade A Standard Convenience Panel for the 1967 Mercury Cougar 

Galvanized three piece replacement tack strips for the 1971 - 1973 Cougar convertible. Over-sized, must be shipped via UPS.

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

C6OE-D and C7AE-F marked fans. Applications: 1. 1968 C code 289-2V engine without air conditioning or heavy duty, or 'extra cooling' option (small radiator). 2. 1969 Boss 302 Eliminator and Mustang. Mustang owners, this 4 blade fan with the part number C6OE-D and (C7AE-F for 1967 and later), is also correct for those K code 289 HiPo engines in both 1966 and 1967. Fan description - 4 blades and 17-1/8 inches in diameter. Ford master part number C6OZ-8600-D. Check out this interesting video...

C5AE-B This is the early 1967 production cooling fan, used up until 11/14/1966 on 289 engine applications. This does not include those cars with factory, or "integral" air conditioning. Fan description - 5 blades and 17 inches in diameter. Ford master part number C5AZ-8600-A. *Note - Excludes integral air conditioning. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

D0ZE-B Applications: 1. *1970 Cougar with one of the **351 engines, with or without air conditioning. 2. *1970 Boss 302 Eliminator or Mustang. Fan description - 5 blades and 17-5/8 inches in diameter. Ford master part number C8SZ-8600-B and casting D0ZE-8600-B. This fan doesn't always carry a 1970 date, our current listing is dated J73 or Sept 1973. *Note - 1970 Boss2 and 1970 351 owners, some cars at the very start of 1970 may have used a C8SE-B marked fan. The C8SE-B fan is identical to the...

C6OE-F Clutch style cooling fan found on all 1967 S code 390 engines, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C6OZ-8600-F. Original fan drive clutch cast number for this application is C7ZE-A. If you have one of these fans and would like to trade it straight across for one of our C8OE-B or C9ZE-E fans please contact us! Check out this interesting video where they test the...

Sold as a pair only, very limited supply. Driver side part number is C7WY-16304-B and passenger side part number is C7WY-16304-A. The casting number imprinted on the part is C7WB-17B957-B for the driver side and C7WB-17B951-B on the passenger side. The Mercury MPC refers to these as "anti squeak pads".

Rare find in NOS form. Sold as a pair only. Driver side carries a C7WY-16304-C Ford part number and the passenger side carries a C7WY-16304-D part number. The casting number on the driver side is C7WB-178951-A and the passenger side has a C7WB-17B957-A casting (or engineering) number imprinted on the top of the part.

Application for all 1971 - 1973 Cougars with factory C6 automatic transmission. Also the correct application for those wanting to install a small block C6 in their 1967 - 1970 Cougar. Original engine options include 351-2V, 351-4V, and 429CJ. We have found two versions of this crossmember, one with three holes in the middle section where the rubber isolator mounts and one with two. This part weighs 2.96 pounds and when set on a level surface, the height of the mounting hole on the driver side...

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

D0ZZ-7528-D Equalizer bar or "Z" bar for 351 cubic inch Cleveland engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use. See the 1969 listing if you have a 1970 351 Windsor engine. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by...

Single cylinder head from 1968 Mercury Cougar 302-2V engines with smog. Sold as a core, needs thorough cleaning and rebuilding prior to use. The 'with smog' cylinder heads would have been found on 3 and 4 speed manual transmission cars. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 61.7-64.7 cc's. With stock pistons, these heads will net an approximate compression ration of 8.7:1. Basic cylinder head number is 6090. Several Ford casting numbers...

Single cylinder head from 1973 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.04 and 1.66 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.0:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D3ZE-6090-AA. 4V in...

Used grade B dash face pad for the standard Mercury Cougar equipped WITH air conditioning. This unit will be nice but will have at least one small crack, usually right in the middle. Give us a call to check availability and to find out if we have the color you're looking for. As usual, this pad could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different color, find...

Used grade B dash face pad for the standard Mercury Cougar that is NOT equipped with air conditioning. This unit will be nice but will have at least one small crack, usually right in the middle. Give us a call to check availability and to find out if we have the color you're looking for. As usual, this pad could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different...

Plastic filler piece that goes over the steering column and bridges the instrument cluster portion of the dash pad. Ford calls this part a "PANEL" (Instrument Panel Cluster) in the Master Parts Catalog. "A" grade used is one without cracks or chips. Put a desired color in the comments section of the online order. We suggest planning on 'painting to match your interior'.  Current color appears to be Aqua Blue. This icon means that we're looking to buy this part!WCCC is a buyer of used and...

Plastic filler piece that goes over the steering column and bridges the instrument cluster portion of the dash pad. Ford calls this part a "PANEL" (Instrument Panel Cluster) in the Master Parts Catalog. "A" grade used is one without cracks or chips. Put a desired color in the comments section of the online order. We suggest planning on 'painting to match your interior'. Ford casting number D0WB-65044D70.

Many people seek this part when changing their XR7 over to factory installed AC. Not only will we give you a substantial credit when you send in your non AC center bezel, we will also carefully match our stock to your bezel to ensure ours does not look out of place when place next to your existing panels. If you send in a substantially faded panel for exchange we will credit back $$$.Finding Grade A dash panels which do not have any fading is nearly impossible. Check back we do get them...

This grade B dash pad will have multiple cracks and will only be usable as a core to adhere our dash repair shell to. Get the shell here.

From the view as seen when sitting inside the car this pad might look decent but when you look at the top side it have cracks, especially at the defroster vents, small blisters and the pad will feel hard on top. This pad will not look perfect even after it has been painted with two coats of SEM vinyl paint as shown here. This pad is not intended for a restored car but is more of a "better than nothing" option. Pictures shown are samples only, not the actual pad you will receive.

Used steel lower dash panel for all 1970 Mercury Cougar and Ford Mustang with factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. Grade B  = some pitting and or extra holes. Replaces Ford part number D0ZZ-6504320.

Used switch for the rear defog or defogger fan on any 1969 Mercury Cougar, 1969 Standard Cougar, and 1969-70 Mustang coupe or hardtop. Original switch with attached wiring harness. Tested and working two speed switch. Comes as shown with chrome knob marked "DEFOG". Some examples may have minor pits in the chrome knob. Wiring marked C9WA-18C498-A. Excludes all convertible models and Mustang fast backs.Replaces Ford part number C9ZZ-18578-A.*Note - is not technically correct for 1970 Mercury...

Also called a pumpkin, 2.79:1 open ratio. Check your door tag under "Axle". 1967 code 0 (zero) 1968 code 2

Also called a pumpkin, 3.00:1 locking ratio.Check your door tag under "Axle".Please note, that this is a vintage, two pin equa lock third member. Most of us should be looking at a modern design traction lock for spirited driving. The 1960's Equa-Lock, is pretty weak.1967 code A 1968 code E

Used dipstick tube for the Mercury Cougar or Ford Mustang equipped with the C6 transmission. The C6 option can be identified by code "U" on your door data plate. Ford part # D0ZZ-7A228-A.

Original dipstick tube. Application 1967 - 1969 Mercury Cougar or Ford Mustang with C6 automatic transmissions, code "U" on your door data plate. Ford master part number C8ZZ-7A228-A.

Reproduction disc brake distribution block for Mercury Cougar or Ford Mustang with factory installed disc brakes. Mounts to the driver side fender apron with a single bolt. Bare block without single pin brake switch.  Replaces Ford part # C7ZZ-2B257-D. Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...

Used Distributor / 289-4V / for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7ZF-12127-H

Used Distributor / 289-4V / Manual Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7ZF-12127-C  

Used Distributor / 302-4V / Manual Transmission for the 1968 Mercury Cougar / 1968 Ford MustangFord part number C8ZF-12127-A  

Used core distributor for 1969 Mercury Cougar and Ford Mustang with M code 351-4V engines with 3 or 4 speed stick. Core distributors will have correct stamping of C9OF-N. Original Ford part number C9OF-12127-N.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with M code 351-4V and automatic transmission. Core distributors will have correct stamping of C9OF-Z. Original Ford part number C9OF-12127-Z.

Used distributor for the Mercury Cougar or Ford Mustang that is equipped with the 351 Cleveland 2V engine.

Good used original distributor for the 351 Cleveland with a 2 barrel carburetor. Ford Part # D2ZF-12127-AA.

Used Distributor / 351C-4V for the 1971 Mercury Cougar / 1971 Ford Mustang Ford part number D0OF-12127-G    

Used core distributor for 1970 Mercury Cougar and Ford Mustang with M code 351-4V and automatic transmission. Core distributors will have correct stamping of D0OF-Z, 351 Cleveland Engine. Original Ford part number D0OF-12127-Z.

Used Distributor / 351C-4V for the 1971 Mercury Cougar / 1971 Ford MustangFord part numbher D1OF-12127-LA  

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-EA.