All Products

Reproduction "A" pillar repair panels for your 67 - 68 Cougar or Mustang. Included in this kit are the two pillar patches and four backing plates for the door hinges.

Reproduction "A" pillar repair panels for your 69 - 70 Cougar or Mustang. Included in this kit are the two pillar patches and four backing plates for the door hinges.

Non working core suitable for rebuild, not full of water and never been opened. These are located in the quarter panel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

Extremely rare open box 1969 Mercury Cougar funny car model kit, AMT # T342 200. Kenz & Leslie Wynn's 777 High Country II funny car with full color cardboard drag display diorama. Unbuilt model kit, complete with contents unopened and still factory sealed inside box (decals are slightly blemished). 1/25th scale, molded in white. Model kit reference guide list the model kit as the one and only 42 year old 1969 issue, never reissued, long out of production. Part of the All...

Good used rubber ram air seal for any 1968-70 Mercury Cougar or 1968 Ford Mustang. May have some warpage issues. 

New manufactured air conditioning condenser for any 1971-73 Mercury Cougar or Ford Mustang. Condenser only, you will need to re-use or purchase a new dryer and possibly other components. 

Redesigned modern evaporator has 35% MORE PASSES, using three-circuits, instead of the original single-circuit design. This is a direct bolt-in replacement and requires no modification.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal. It has been our experience that these often fail within a few years. We suggest flushing and pressure...

Reproduction air conditioning evaporator for early production Mercury Cougars and Ford Mustangs. This early 1969 version has inlet and outlet tubes that run horizontally, in the later 1969-70 version, these tubes run diagonally off of the core. Please note the type of connection that you have. This item uses "O" - Ring style fittings. 1967-68 and some very early 1969 cars were using compression fittings. *Note - We have had numerous customers complain that these don't fit exactly like the...

Reproduction A/C evaporator for the later production 1969 - 1970 Mercury Cougar and Ford Mustang. This later version of the evaporator has inlet and outlet tubes that run diagonally of the core as opposed to the early version where the tubes run horizontally.*Note - We have had numerous customers complain that these don't fit exactly like the originals. As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies...

Reproduction A/C evaporator for your Mercury Cougar or Ford Mustang.*Note - We have had numerous customers complain that these don't fit exactly like the originals.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal, which also equals out to performance that's sub-par to a good used original evaporator.Click on images to enlarge. ...

Regardless of which V-8 engine, C9ZA-19837-A or C9ZA-19837-C both are the correct part number. This hose is approximately 68 inches long. Ford part # C9AZ-19837-A.

This is actually a kit which includes 2 hoses (Part # D1ZA-19835-A and Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342), 2 o-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316) and a quick connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252). *Note we normally supply the new coupler with this kit. Regardless of which V-8 engine, this hose when assembled is approximately 78 inches long.Ford MPC kit #...

This new chrome interior A/C vent register kit is spot-on! Comes with all three knobs and is a direct fit with your existing OEM ducts, switches, and switch linkage parts. Dealer pricing is available.

Finally, an answer to the much needed, delicate 1968 air conditioning side vents! Visually, these are very hard to tell apart from the originals we have listed on this site but functionally they are much better in that they are cast in one piece. The originals were very prone to breaking and often when you close the door on your 1968 Mustang, Cougar or Shelby the lower portion of the vent falls off. This kit is correct for the 1968 Mercury Cougar only and it includes all three knobs and the...

NOS 1967 Mercury accessories and factory installed optional equipment binder. This catalog was used in the dealerships to upsell customers on a variety of options available for their car. It details options from appearance, comfort and convenience, performance and other miscellaneous items such as fire extinguishers and tire chains.  This is a rare find, dealers were the only ones who were issued these binders, and this one happens to be in great condition.

C8AE-9B452-B Thermactor smog pump belt tensioning adjustment bracket. Application is for all 1968 - 1970 FE engines with factory installed thermactor smog systems.

Reproduction thermactor smog pump adjusting bracket for all 1968 Mercury Cougar and 1968 Ford Mustang with S code 390-4V engines. Additionally this bracket was also used on 1968-70 Mercury Cougar and Ford Mustang with 428 Cobra Jet engines. Quality made product. Ford number C8AE-9B452-B.

Reproduction thermactor smog pump adjusting bracket for all 1970 Mercury Cougar Eliminator and 1970 Ford Mustang with Boss 302 engines. Quality made product. Replaces Ford part number D0ZE-9B452-A. We also have one copy of an earlier reproduction version without the stamped  D0ZE-9B452-A, on the part. Call 503-436-1130, will be sold at a good discount, just ask.

Reproduction GT style concours correct air cleaner assembly with a chrome lid and California emissions tube for all Mercury Cougars and Ford Mustangs equipped with the 390GT engine. This is an extremely hard piece to find used and even rarer in NOS form. Now we can offer you this new unit that is made from the original tooling! This reproduction includes a blue base, a chrome lid, and a lid to base rubber gasket. This is also an excellent stock appearing performance upgrade for the very...

Nice used air cleaner assembly, includes base, snorkel, heat riser and air cleaner lid. Application is any 1967 Mercury Cougar or Ford Mustang with C code 289-2V or A code 289-4V engines without emissions. All good parts as shown, thermal switch in air cleaner snorkel may not work, and no we cannot test them.Even if you are not currently running all original parts under the hood this is a great set to stow away as these items are going up in price and add value to your car when the time comes...

Nice used 1968 air cleaner assembly, includes base with elbow, snorkel with vacuum operated flapper, heat riser and air cleaner lid. Application is any 1968 Mercury Cougar or Ford Mustang with C code 289-2V or F code 302-2V, or J code 302-4V engines with closed emissions. All good parts as shown, vacuum controlled flapper in air cleaner snorkel may not work, and no we cannot test them. This style of vacuum operated flapper was used at the beginning of the 1968 model year. There was a change to...

California emissions 390 engines only. Uses 4 bolts for mounting the drive pulley, the 390 pump has three air ports on the reverse side. Ford part number C6AZ-9A486-E. *Consider these used pumps as cores. We cannot warranty these pumps to work like new.

Grade B used panel with all parts removed. Panel measures 19.5" x 37". Whereas at first glance these may all look the same, the contour of the roof changes with the body style changes. Grade B will have some rust through in several places. 

The automatic seat back release option for 1971 to early 1972 (before December 1971) Mercury Cougar and Ford Mustang. The automatic seat back release would pull the release lever on both of the bucket seats. This only happens when the either the driver or passenger side door is opened. Kit comes with the 1971- early72 specific wiring harnesses from the solenoid, includes 3 pin switch for the passenger pillar post, relay, solenoids, and cross over wiring. This option is best added to seats...

The automatic seat back release option for 1973 Mercury Cougar and Ford Mustang. The automatic seat back release would pull the release lever on both of the bucket seats. This only happens when the either the driver or passenger side door is opened. Kit comes with the 1973 specific wiring harnesses from the solenoid, includes 3 pin switch for the passenger pillar post, relay, solenoids, plug for retractable seat belts, and cross over wiring. This option is best added to seats prior to...

The automatic seat back release option for Mid 1972 (after December 1971) Mercury Cougar and Ford Mustang. The automatic seat back release would pull the release lever on both of the bucket seats. This only happens when the either the driver or passenger side door is opened. Kit comes with the mid 1972 specific wiring harnesses from the solenoid, includes 3 pin switch for the passenger pillar post, relay, solenoids, plug for retractable seat belts, and cross over wiring. This option is best...

Bare housing with proper axle pad spacing for all 1967-1968 Cougars with 289 or 302 engines. Over-sized shipping length. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. This axle housing was used starting about mid 1967. It does not have the fill plug in the rear of the housing. * Important - Please check your car to verify that your 8 inch third member has a fill plug. Replaces Ford part number C7ZZ-4010-E. ...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Spring perches are 43 inches apart on center. Complete rear end housing - drum to drum, with axles, and with pumpkin. 1967 EARLY 8 inch rear end housings with fill plug in the steel housing as seen...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Axles used: Passenger side - 31-1/8 inches long, Driver side 27 inches long. Complete rear end housing - drum to drum, with axles, and with pumpkin. For...

Housing overall width - 55-3/4 inches flange to flange. Spring perches are 43 inches apart on center. Bare housing with proper axle pad spacing for all 1971-1973 Cougars. Over-sized shipping length.Axles needed: Passenger side - 32 inches long, Driver side 28 inches long.

We are excited to bring these new reproduction chrome backup light bezels for the 1969 and 1970 Mercury Cougar to the market. The sockets, pigtails and lenses are not included so you will need to gently remove your originals and install them in these bezels. You can find the lenses here.

We are excited to bring these new reproduction assemblies for the backup lights for the 1969 and 1970 Mercury Cougar to the market. Includes a pair of bezels with lenses and gaskets. The sockets and pigtails are not included so you will need to gently remove your originals and install them in these bezels.Click on images to enlarge. The chrome finish is brilliant and mirror smooth.  There are no polishing marks like evident on so many of the NOS bezels we see. The lenses have a clear look...

D2ZF-9600-EA Air cleaner base for all 1972 Q code 351CJ engines. About 16.79" inches in diameter. Could also be found under casting number D2ZF-9600-KA. Ford part number D2ZZ-9600-E.

Factory air cleaner base for all S code 1967 Mercury Cougar non-GT or with the 6.5 Liter option, 1967 Mustang 390-4V without the GT option, and 1967 Ford Thunderbird with Z code 390-4V or Q code 428-4V engines. 49 state versions like this do not have the steel elbow on the air cleaner side which became standard on cars beginning in 1968.

Manual transmissions, include both 3 and 4 speed Top Loader transmissions. For use with 164 tooth flywheels. For use with all 1968 302 engines and 1969 - 1970 Boss 302 Eliminators. Cast aluminum construction. Shipped bare, no hardware or clutch fork. Search words 68 69 70 small block F J G code. Ford part number C5AZ-6392-BCasting number C5AA-6394-B *Note - This is not a replacement for 1970-1977 Ford Maverick or Mercury Comet 302 engines. See part C5DA-6394-A with 157 tooth flywheels. ...

Grade A used A/C center vent for standard (non XR7) model Cougars. These will have almost perfect chrome plating, minor blemishes only, no major pitting. Fits the standard model (65A or 65C) Cougars with padded dash face pads. See our other listing for Grade B versions of this air conditioning center register or vent.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.

Sold as a pair, we suggest you send your cores in advance or at least email us several good quality images if your cores are questionable. If your cores are heavily pitted, cracked or the studs have been over tightened (causes part to dimple / warp) then your cores are not acceptable for restoration. The casting number as seen from the back reads C9WB-15A509-B and C9WB-15515-B. Ford Part # is C9WY-15500-B and C9WY-15500-A

Restored driver (left hand) side headlight bezel moulding for any 1971-72 Mercury Cougar. We also have grade A and B used mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If you pay the core charge...

Restored driver (left hand) side headlight bezel moulding for any 1973 Mercury Cougar. Chromed only, detail black painted portions not completed. We also have grade A and B used mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had...

Restored passenger (right hand) side headlight bezel moulding for any 1971-72 Mercury Cougar. We also have grade A and B used mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If you pay the core...

Restored passenger (right hand) side headlight bezel moulding for any 1973 Mercury Cougar.  Chromed only, detail black painted portions not completed. We also have grade A and B used mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored...

Driver side left hand headlight door. We have many good used head light doors in stock, give us a ring!

New Old Stock 1973 Mercury Cougar Driver side, headlight door.  Casting number reads D3WB-13064. Ford part number D3WY-13064-B

Passenger side right hand headlight door. We have many good used head light doors in stock, give us a ring!Casting number reads D1WB-13052.Ford part number D1WY-13064-A

New Old Stock 1973 Mercury Cougar Passenger side, headlight door.  Casting number reads D3WB-13052. Ford part number D3WY-13064-A

This is an uncut, pit free, crack free radio bezel. She is mint, no excuses! Keep in mind we have bezels that have been altered for an after market radio for much less money.Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being different. The 67-68 Mustang console also had this slide up door. This slide up door works like the...

This was used only on the 1968 Mustang and standard Cougar, not for XR7. If you would like one that has been modified for an after market radio or you would not mind other minor blemishes (Or a broken ear) we have several that would save you money.Ford casting number C8ZB-6504567-C This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or...

This used bezel is covered almost entirely by the face pad with clock. Only the small area around the radio actually shows once installed. This early bezel has the upper support, the later version is open. Keep in mind we have bezels that have been altered for an after market radio for substantially less money. Ford casting number C7WB-6504567-B  68102-171 Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling. All 67-68 standard consoles had a...