1973 Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used wire loom plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Non-original style replacement clip for mounting the quarter window regulator arm to the window channel bracket on all 1969-70 Cougar and Mustang coupe and convertibles. This clip will work with either the 1969-early 1970 bracket and the late 1970 bracket. The late 1970 brackets used a unique spring steel clip that seldom is reusable. Sold individually, one each per window.

This item holds the release bale to the upper knuckle. It is different than the 67 - 69 clip although both can be used. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually.  Replaces Ford part number 382929-S.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S

Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.

Used black plastic clip that goes onto the lower center of the firewall of any 1969 Cougar or Mustang. Also found on the back of the instrument cluster on the 71 - 73. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is...

Clips or clamps for attaching the 3/8" hard fuel lines to the body of any 1968-73 Mercury Cougar or Ford Mustang. Clips only, save your attaching body bolts. Sold in packages of 4 clips as shown. Will work on 1967 cars if you change to 3/8 lines. 1971-73 Cougar owners can use item 27565 attaching bolts, they are the same as the fuel tank mounting bolts. See related items. Replaces Ford 354663-S8

Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.

Rebuilt quartz movement clock for the 1971 - 1973 Cougar or Mustang. Quartz movement clocks have second hands that click around, original clocks had a constant sweep of the second hand.

Adjusting rod - Lower clutch rod that fits between the Z-bar and the clutch fork. Replaces Ford Part # C8AZ-7521-B THIS FITS: 1971 1972 1973 MUSTANG 6 CYLINDER 302 351C BOSS 351 1971 MUSTANG 429CJ 429SCJ 1972 1973 1974TORINO351C 351 CJ 1968 1969 1970 1971GALAXIE 6 CYLINDER 302 351 390 429 1968 1969 1970 1971 MERCURY FULL SIZE351 390 429 1971 COUGAR429CJ 429SCJ 1971 1972 1973COUGAR 351C 351CJ 1972 MONTEGO6 AND 8 CYLINDER

D1ZZ-7528-C Equalizer bar or "Z" bar for 351 and 429CJ engines with a manual transmission. Used up after 4-30-1971. Both 3 and 4 speed manual transmissions. Also fits Mustang with Boss 351. NOS part.*Note - Before 4-30-1971 use Ford part D1ZZ-7528-A.

Reproduction D1ZZ-7528-C Equalizer bar or "Z" bar assembly, for 351 and 429CJ engines with a manual transmission. Fits all years 1971-73 Mercury Cougar and Ford Mustang. Includes frame rail bracket and clutch rod as shown. 

Clutch equalizer pivot mount, engine side. Fits all 1971 - 1973 Mercury Cougar with 351 Cleveland engine, and 1971 - 1973 Ford Mustangs with 302 or 351 Cleveland engine.  Replaces Ford part #: D1ZZ-7A572-A.

C8AZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12-5/16 inches long. Alternate number C8AA-7515-B or C8AA-7541-B. Couple of variations of this fork. Most versions will not be stamped. Spring and side holes not needed for Mustang and Cougar applications. Originally for 1968 full sized cars with 289 or 302 engines and manual transmissions. Maybe 6 cylinders, not sure, but vert likely. Cougar 1971 - 1973, 351 Engines. Mustang 1971 - 1973,...

Clutch Fork Pivot for Cougars manufactured after 2/16/1968. Replaces Ford Part #: C8AZ-7522-A.

Manual transmission clutch kit for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is a 10 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.

These clutch pedals feature an improved design (removable pin) for easier installation. Compatible with existing hanger assembly even in automatics. Replaces Ford Part # D1ZZ-7519-B.

D1ZZ-7519-B Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

These reproduction pads are high quality replacements for worn or missing original pads. Replaces Ford part number C9ZZ-7A624-A.

Stainless Clutch Pedal Pad Trim. Replaces Ford Part #: C9ZZ-7B544-A.

Manual transmission clutch throw out bearing for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is with a 10 inch disc.

These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.

Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.

Fits 1968 - 1973 Standard or XR7

These emblems can be used anywhere from your toolbox, to the dash or trunk and anywhere in between. Makes a great accent to other fender emblems or door panels. Peel and stick.Sold as a pair.

Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. Listed in the...

Used coil mounting bracket. This version of the bracket is probably the most common. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. This version has the notch as shown. We know that this version was used on...

We will loan this coil spring compressor for 60 days, with a 100% refundable purchase price. This tool now comes with a bearing to make the job much easier. Only available to customers that purchase our front suspension rebuild kits. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Coil spring compressing tool, this is a must for safely removing front coil springs on any 1967-73...

Used driver side (left hand) coil spring cover that is a good solid western part for Mercury Cougar and Ford Mustang.Ford part # D1ZZ-3383.

Reproduction driver side (left hand) outer shock tower cover for Mercury Cougar and Ford Mustang. We cannot stand behind this product as it is an ill fitting reproduction, however do offer rust free used originals. No returns accepted.

Reproduction passenger side (right hand) outer shock tower cover for Mercury Cougar and Ford Mustang. We cannot stand behind this product as it is an ill fitting reproduction, however do offer rust free used originals. No returns accepted.

Used passenger side (right hand) coil spring cover that is a good solid western part for Mercury Cougar and Ford Mustang. Ford part # D1ZZ-3382.

Made from soft flexible rubber very similar to the OEM material. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. If you prefer polyurethane insulators, you can find them here. Replaces Ford Part #: C4DZ-5415-A.

Features quality stamped steel construction, bushings, nuts, anti-squeak coil protector pads. From the get go these were never a very good design... The rubber is prone to cracking and the unit will bind under severe use. Not just speaking of the unit we are offering but all of them including the original Ford units. Here is an interesting article for those that are not happy with status quo. Global West and others have come up with their own solutions and after we have spent more time testing...

High Performance Coil Spring Perches offer a very affordable upgrade to stock spring perches with rubber bushings. These are made with synthetic elastomer bushings which are similar to polyurethane in performance and longevity, but will not squeak like polyurethane. The perch can rotate 360 degrees on the shaft, which allows the front suspension to articulate freely. This feature also eases the installation of the coil spring. Zerk grease fittings are installed and locking nuts are included....

Replica of the coil spring shipping tag that would have been found on factory delivered 1967 - 1973 Cougars and Mustangs.

These Linear springs are custom wound for the performance-oriented customer. These feature 600-pound/inch rating and will lower the car approximately one inch from stock. Painted black, sold as a pair. Note: If you look close at factory sales pictures from the day you will notice the cars sit about 1" lower in back than front. These springs will level the car out provided your rear leaf springs are not sagging.  Linear springs are the easiest to understand. When you think of a spring,...

Unique to the 1973 Mercury Cougar and Ford Mustang with 351 engines. This is only the upper section of a two piece ducting that connects to the air cleaner snorkel with a flex tube. The Ford MPC specifies that this is only for the 351-2V and 351-CJ (351-4V) engines.Replaces Ford part number D3ZF-9A624-A.

Used steering column shroud or collar for any 1971-73 Mercury Cougar or Ford Mustang. These come in various colors, and have a smooth texture. These will have some scratches in the surface, specify your desired color in the notes or comments section, but do know that black is in short supply. Ginger anyone?*Note does not include the retainer or clip, we cannot keep them in stock.Replaces Ford part numbers D1ZA-3530-A, D1ZZ-3530-A,D3ZA-3530-A, and D3ZZ-3530-A. ...

Complete reprint of 11 Supplemental Off Highway Performance Operation Parts Newsletters from Ford which were printed between January 1972 and Spring of 1973. Full of tips on modifying your vehicle for Drag, Strip and Oval Racing.

Complete reproduction front drum brake spring kit for Ford Mustangs equipped with 9" drums. This kit contains all the replacement springs and hold downs required to do a professional brake job on front drum brakes. Kit includes enough parts for two wheels.

Complete floor pan for the 1969-70* Ford Mustang or 1969-70* Mercury Cougar. This item ships direct from the manufacturer for most orders. This item must ship via truck freight. Shipping to business addresses tends to be less than residential addresses, sometimes substantially.This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes...