1973 Ford Mustang

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Reproduction tack strip for the rear bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the rear bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 Feet (60 inches) of material and will have to trim to fit your top. You can also...

The decal I most often see on the 1971-1973 Cougar is the used one pictured here. Will be trying to locate this decal soon.

Currently, Convertible Tops dropshipped from this supplier will not ship for 4-6 weeks. The original tops would have been double texture PinPoint Vinyl. There are 3 different materials currently offered for these premium tops. Single Texture PinPoint Vinyl (GOOD): This is the material that is offered by almost all Mustang Vendors and it looks the same on the surface as an OEM top. This is a two-ply composite which has an outer layer of canvas-looking PVC vinyl plastic, and an inner layer of...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling.  See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps, so any boot that comes with snaps is not...

Used to cushion and protect top vinyl from excessive wear from side rails. Replaces Ford part #: D1ZZ-7652875.

Passenger side inner convertible top rail extension, made of cast aluminum. One of the most fragile parts on the convertible top assembly. Prone to failure when one of the hydraulic cylinders fails and the top assembly is forced. Comes as shown, be sure to save all of your installation hardware and bushings. Casting number on part reads: D1ZB-76531A08-A.

Retainer and screws used to retain the header seal.Fits:1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang

New to the Market! Correct convertible side tension cables for the 71 through 73 Cougar and Mustang.  Replaces Ford Part #: D1ZZ-652806-A.  

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

Replaces Ford Part #: D1ZZ-7650509-A

Replaces Ford Part #: D1ZZ-7650508-A

Driver side inner convertible top rail extension, made of cast aluminum. One of the most fragile parts on the convertible top assembly. Prone to failure when one of the hydraulic cylinders fails and the top assembly is forced. Comes as shown, be sure to save all of your installation hardware and bushings. Casting number on part reads: D1ZB-76631A09-A.

Driver side convertible rear top rail, made of cast aluminum. One of the most fragile parts on the convertible top assembly. Prone to failure when one of the hydraulic cylinders fails and the top assembly is forced. Comes as shown, be sure to save all of your installation hardware and bushings. Sometimes there may be a broken screw for the cable that will need to be drilled out.  Casting number on part reads: D1ZB-7653139-AB.

Passenger side rear convertible top rail, made of cast aluminum. One of the most fragile parts on the convertible top assembly. Prone to failure when one of the hydraulic cylinders fails and the top assembly is forced. Comes as shown, be sure to save all of your installation hardware and bushings. Very hard part to find unbroken, sometimes the screws break off for the cables. You may have to drill out a broken screw.  Casting number on part reads: D1ZB-7653138-AB.

Our well (or boot) liners fit correctly. Made of heavy duty, textured vinyl.

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

No excuses 100% complete mechanism with no cracks, missing parts or heavy corrosion. We can include the top cylinders but will not guarantee they will not leak. We carefully break this down by removing the header and crossbows and placing the original bolts back in the holes. Once you get this from UPS it will be very evident how it goes back together.

Reproduction Convertible Top Utica Plant Decal for the 1970 - 1973 Mercury Cougar or Ford Mustang 

C6AE-E Multiple applications over the years. 1. Later 1967 production cooling fan, generally used after 11/14/1966 on most 289 engine applications. 2. 1968 302 without air conditioning. 3. Mid year (after 11/6/1968) 1969 351 without air conditioning. 4. 1969 Early Boss 302 before 4/14/1969. 5. 1971 Cougar with 351 engine, without air conditioning. 6. **1973 Cougar 351-2V without air conditioning prior to 2/19/1973. Fan description - 4 blades and 17-1/2 inches in diameter. Ford master part...

C9OE-A radiator cooling fan. Multiple applications over the years. 4 blade fan, 14 inches in diameter. Not sure when these actually started being installed on the assembly line if at all. The C6AE-E version was used well into 1972 or later. Ford part number C9OE-8600-A. *Note - Excludes integral air conditioning. **Note - 1973 there is a note in the MPC that states this fan may be marked C9OE-A. Check out this interesting video where they test the efficiency of factory style and...

D2OE-AA Applications: 1. 1972 Cougar with H code 351-2V engines - without air conditioning. 2. 1973 Cougar with H code 351-2V engine after 2/19/1973 - without air conditioning. May also be marked D2OE-AB. Fan description - 4 blades and 18-1/2 inches in diameter. Ford master part number D2OZ-8600-A. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

D2OE-AB Applications: 1. 1972 Cougar with H code 351-2V engines - without air conditioning. 2. 1973 Cougar with H code 351-2V engine after 2/19/1973 - without air conditioning. May also be marked D2OE-AA. Fan description - 4 blades and 18-1/2 inches in diameter. Ford master part number D2OZ-8600-A. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

D2SE-AA Applications: 1. 1972 and 1973 Cougar with H code 351-2V engines and air conditioning. 2. 1972 and 1973 Cougar with Q code 351-4V or 351CJ engines with or without air conditioning. Fan description - 5 blades and 18-1/2 inches in diameter. Ford master part number D2SZ-8600-A.Interesting Ford recall article for your reading enjoyment. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most...

Copper crush washer for all disc brake hoses and calipers 1968-73 Mercury Cougar and Ford cars like Mustang. Size 0.39" x 0.62" x 0.062". Four needed per car, two per side (one on each side of the disc brake hose end) sold indiividually.

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

Replaces Ford part #C1SZ-13783. Replaces burnt, cracked or missing original lenses located above the rear package tray.  Two required per car, sold individually.

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

Replaces Ford part #D1ZZ-13915-A. Comes in black only, used in conjunction with 73 Deluxe Horn Blow Switch Trim Plate

Covers the metal, foot operated headlight dimmer on the driver side floor pan. Replaces ford part #: C5ZZ-13533-A.

This cowl is made for a car without AC but all you have to do to modify for a factory AC car is plug the vent hole on the driver side. Replaces Ford part # D1ZZ-6502010-A.

Crankshaft oil slinger for all small block Ford V-8's, starting 1963 until at least through 1973. 1963-68 289 and 289 HiPo engines. 1968-73 302 engines, 1969-70 Boss 302 engines, 1969-73 351W engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter about 2-7/8 inches. Ford part number C3OZ-6310-A.

Crankshaft oil slinger for all 351C or Cleveland engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines.  Ford part number D0AZ-6310-A.

CRC contact cleaner is intended for cleaning sensitive electronics and electrical equipment. Great for cleaning edge connectors, buss bars, circuits, contacts, printed circuit boards, switches, circuit breakers, etc. Safe on most plastics.

For all 1971 to 1973 Cougars and Mustangs with H code 351-2V and FMX automatic transmissions.  Ford part number D1ZZ-6A023-B.*NOTE* Two notes - There is a difference between 1969-70 and 1971-73 FMX cross members. Additionally, Ford did produce H code 351-2V engines with C-6 transmissions. Triple check.

Good quality reproduction front cross member for your 71 - 73 Cougar or Mustang. This is the frame / body piece that goes underneath your core support and receives the front ends of the strut rods. Sold as a stand alone part and does not come with strut rods or any strut rod hardware.Width: 34.75"Diagonal from outer bottom corner to outer top edge: 5"

Reproduction Crossmember / Under Engine for the 1971 - 1973 Mercury Cougar / 1971 - 1973 Ford Mustang 

Parking brake return spring cup for the 69 - 73 Cougar or Mustang. This cup sits at the end of the spring and is held in place by an adjusting nut. It's used to keep the spring from sliding off of the front emergency / parking brake cable.

1973 Front unibody cut with cowl. This cowl has the holes for the factory air conditioning. 1971-72 frame rails are constructed differently for the non-energy absorbing front bumpers. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual aprons, towers, radiator...

1973 Front unibody cut with cowl. This cowl has the holes for the factory air conditioning. 1971-72 frame rails are constructed differently for the non-energy absorbing front bumpers. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual aprons, towers, radiator...

Comes with good shock towers, front aprons, and core support. This is a great value for those that need to replace multiple parts upfront as you will not only get factory joined parts that will save you money and time, but it will also  preserve the value of your car. With a clean Western cut like this, one should be able to install it so that nobody would ever know your car has had anything replaced. You will have to call to order this one. Expect to pay about $300 for crating and...

Single cylinder head from 1970-73 Mercury Cougar with H code 351C-2V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.04 and 1.65 inch valves, and the chambers measure out at 78.2 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0AE-J. 2V in the...

Single cylinder head from 1972 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.6:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D1ZE-6090-GA. 4V in...

Used metal dash support brace for all 1971-73 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 10 inches long. Replaces Ford part numbers D1ZB-6504672-A.