Interior

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. These are for Standard level interiors only.

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. These are for Standard level interiors only.

Used middle console support bracket. Held in place by 2 rivets midway under the console.

Grade A condition - passenger side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1968 Mercury Cougar, passenger side only. Found on XR7 and most Standard model Cougars. Grade A condition, will have supple vinyl without damage. minor or no de-lamination. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best...

Used interior quarter window moulding for the driver side (left hand) of the Mercury Cougar coupe. This trim installs vertically behind the quarter window. Unfortunately we cannot guarantee we will be able to supply the color of your choice, but we will try to accommodate.

This passenger side (right hand) moulding is correct for hardtop or coupe. On convertibles, the top portion is trimmed to allow it to slide under the sun visor bracket. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-6503598, engineering # imprinted on the back D1ZB-6503598 for 1971-72, D3ZB-6503599 for 1973. *NOTE* Excludes Mustang Fastback and Mach 1 models. This...

This driver side moulding is correct for hardtop or coupe. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Master part number D1ZZ-6503599.*NOTE* - Excludes Mustang Fastback and Mach 1 models. ...

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang. These units are sold as a pair.

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang that feature two 2" gauge pods on the driver side. Sold as a pair.

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

This passenger side moulding is correct for convertible. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503598 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-7603598. *NOTE* Excludes Mustang Fastback and Mach 1 models. ...

Dash pad attaching nut 8-32 threads original zinc plate and dichromate. 5 of these nuts are used to attach the dash pad to the painted steel upper dash panel  (D1ZZ-65044D90-A) on 1971-73 Mercury Cougar and Ford Mustangs. Sold individually.Replaces Ford part number 45271-S36.

Rare find in NOS condition! These are new, never used original manuals and no reproductions have been made. Limited quantity.

This is the second printing so it does include the xr7 package.

Reproduction Owners Manual for the 1968 Mercury Cougar

Has correct textured cover. Quality reproduction.

Good used original insulation pad as taken from a Western parts car. Used Jute pad that will not have any water or pest damage. These original pads are nice because they are made from a much more dense material (3.74 pounds) than the reproductions (.75 Pounds) and they have the factory perforated "knock out" sections for the optional speakers. A "Must Have" for show cars as the rear package tray fits better with this low profile material and no modern insulation resembles the original when...

There currently are no reproductions of this curved, thin package tray. Included with the tray are both slender strips of thin sound deadener / insulation. These package tray cover boards will not have heavy water damage, but will need paint. Replaces Ford part number D1WY-6546668-A.

Nothing matches the fit and feel of NOS. This will outlast the reproduction armrest three to one.

Base standard saddle arm rest on a 1967 Mercury Cougar or Ford Mustang, interior trim code 2F. Nothing matches the fit and feel of NOS. This will outlast the reproduction armrest three to one. Ford part number C7ZZ-6524140-A1F.

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake...

One required per car, mates to female version attached to the under dash loom. Same plug for tilt and non tilting columns.

Factory radio delete or block-off plate from a 1967-68 Mercury Cougar or Ford Mustang. Seldom seen part, roughly 5% of all 1967-68 Mercury Cougars were ordered without any type of radio from the factory. Similar story with the Ford Mustang, most owners added some sort of radio or stereo soon after delivery. The factory radio bezels were made from chromed pot metal, these radio delete plates are made from plastic and vacuum chrome plated. This used example pictured, has most of the plating...

This pad in unique in that it has four holes for the four warning lights found in cars with the convenience control package. In cars with no AC and no console the rectangular panel was located in the center of the dash face pad. You can expect a grade A pad to have no burns or cracks and still be pliable. Count on painting it as there is almost always fading after 50 years and we may not be able to supply the color you need. When you order mention the color you desire and we will try to to...

Used grade A radio pad for the center console of the Mercury Cougar or Ford Mustang. The color will be right and bright and there will be no cracks or warping. This unit will be mint, no excuses! *NOTE* We rarely can provide the color you need due to the very limited supply we have. 

This is going to be a grade "B" pad, so expect it to show signs of warping and de-laminating. It will most likely be sun damaged, and the holes around the radio knobs may be elongated. We cannot guarantee that we can give you the color you select, so plan on repainting this item. Even if we can provide your color, there is always some discoloration from age and use.

Good used part without excessive rust or damaged rubber. For use with fixed column only. 1971-73 rag joints are different than the 1967-70 variety. The 1971-73 Cougar and Mustang steering box has a larger diameter shaft for attachment. Check out this video

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1971 1972 1973 Cougar tilt columns. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse one of your factory ones. Splined end slightly larger than previous years, due to the upgraded integral steering box unique to the later Cougars. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Used rear console support bracket for the 69 Cougar or Mustang. Mounts under the leading edge of the storage compartment under the console.NOTE - 69 and 70 used different brackets

Used driver side (left hand) bare rear interior panel for the Mercury Cougar. This rear panel is just the plastic backing panel without the vinyl. We sell the panels this way so that you can save some hard earned money by reusing your existing vinyl from your broken or damaged rear interior panel. Keep in mind that these panels are almost 50 years old, so minor cracks and chips will usually be present.

Used passenger side (right hand) bare rear interior panel for the Mercury Cougar. This rear panel is just the plastic backing panel without the vinyl. We sell the panels this way so that you can save some hard earned money by reusing your existing vinyl from your broken or damaged rear interior panel. Keep in mind that these panels are almost 50 years old, so minor cracks and chips will usually be present.

This panel was used on all convertible models without retractable rear belts. Please contact us for choice of color, power or manual windows and with or without seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled.

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used the full 1971 model year and early 1972 and is for use in cars with no rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used the full 1971 model year and early 1972 and is for use in cars with no rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

Used décor rear interior panel in aqua for the driver side (left hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Decor style rear interior panel for 1970 Mercury Cougar hardtops. Decor is one level above the base standard interior. Interior code for base standard interiors starts with 1, Decor interior codes can start with 3, 5, or E, followed by another letter denoting color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

Decor style rear interior panel for 1970 Mercury Cougar hardtops. Decor is one level above the base standard interior. Interior code for base standard interiors starts with 1, Decor interior codes can start with 3, 5, or E, followed by another letter denoting color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

This panel was used the full 1971 model year and early 1972 and is for use in cars with no rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

Used décor rear interior panel in dark red for the driver side (left hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used décor rear interior panel in dark red for the passenger side (right hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Decor style rear interior panel for 1970 Mercury Cougar hardtops. Decor is one level above the base standard interior. Interior code for base standard interiors starts with 1, Decor interior codes can start with 3, 5, or E, followed by another letter denoting color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

Standard style rear interior panel for 1970 Mercury Cougar hardtops. Standard interior was the base level interior design. Interior code for base standard interiors starts with 1, Decor interior codes can start with 3, 5, or E, followed by another letter denoting color. Armrests sold separately. Specify if your needs require power window cutouts in the comments section.

All of our Standard and Decor, 1967 and 1968 rear interior panels come naked without the horizontal basket weave strip. We often will leave a yellowed, peeling one in place when they ship but if they are in good shape we remove them and sell them separately. If you purchase a panel from us and want a grade C strip, just mention it in the comments section of your online order and we will include it for free. Used passenger side (right hand) rear interior panel in black for the Mercury Cougar....

This panel was used the full 1971 model year and early 1972 and is for use in cars with no rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.