Interior

Ford part number 3E629. Molded rubber construction, fixed and tilt steering columns. These may have been used as early as late 1972, not sure. Limited stock. The reproduction plastic version for 1969-72 will also fit and work in conjunction with the available foam insulation. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

We can honestly say these are much better than the originals when it comes to durability. The originals were backed with a "fiber-board" that was prone to failure in the clip areas and almost always curl at the edges with age. These new panels are backed in sturdy, moisture proof ABS plastic and covered with the correct textured vinyl. Secondly this much improved new version does not crack in the arm rest area like the originals. You will have to reuse your original decorative trim, emblems...

We can honestly say these are much better than the originals when it comes to durability. The originals were backed with a "fiber-board" that was prone to failure in the clip areas and almost always curl at the edges with age. These new panels are backed in sturdy, moisture proof ABS plastic and covered with the correct textured vinyl. Secondly this much improved new version does not crack in the arm rest area like the originals. You will have to reuse your original decorative trim, emblems...

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers so if speaker holes are needed you will have to use your old panels as a template to drill holes in these "Mustang" reproductions. Replaces Ford Part number C7WY-650345-A1G / Casting number as seen on the back of the driver side will read C7WB-6502345-BW

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Reproduction interior kick panels in parchment / off-white for the Mercury Cougar or Ford Mustang. Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Door Tag Trim Code: 6Z. Brown / Dark Tobacco XR7 Vinyl upholstery to cover the front buckets and rear seat.*NOTE* This product will take 4 – 6 weeks for delivery.

Door Tag Trim Code: 6Z. Brown / Tobacco XR7 vinyl upholstery to cover the rear seat.*NOTE* This item will take 4 - 6 weeks for delivery.

Door Tag Trim Code: 6Z. Brown / Tobacco XR7 Vinyl upholstery to cover the front buckets and rear seat.*NOTE* This product will take 4 – 6 weeks for delivery.

Door Tag Trim Code: 6Z. Brown / Dark Tobacco XR7 Vinyl upholstery to cover the rear seat.*NOTE* This product will take 4 - 6 weeks for delivery.

Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This mounts at the top front corner of the driver side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B.You may also need the attaching screw. Replaces Ford part number C7WY-6531491-B or C7WB-6531491. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

This mounts at the top front corner of the passenger side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B.You may also need the attaching screw. Replaces Ford part number C7WY-6531490-B or C7WB-6531490. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

Black ABS plastic replacement kick panels without speaker pods. Sold as a pair. Reproduction kick panels made for 1971-73 Ford Mustang, but will fit a 1971-73 Mercury Cougar OK.

Reproduction insulation located behind the kick panels on the 71 - 73 Cougar or mustang. Correct cut allows access to the door hinge bolts.

Factory knob for the new for 1968 rear window defogger. This is the knob for the 2 speed fan switch mounted to the bottom dash on cars so equipped. Rare option, we try and match these up to the switches. Spares occasionally come in, subject to availability.

Good reproduction of a knob that is always broken off. Made from milled aluminum rather than plastic as the originals were made. This makes it so it is not as susceptible to breaking off. Unique to Cougars with tilt columns in 1968 - 1969. Replaces Ford part number C8MY-17513-C. This part also fits the 68-69 Mustang, Lincoln, Marquis, Thunderbird and other like models with an adjustable steering column.

Used emergency flasher knob for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is a very fragile part which we never find in good used condition. What you will see when it has been broken off is an exposed Phillips screw head. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes...

Hard to find knob with no crack or peeling issues, correct for right or left side Torino, Cougar, Mustang. Not for use with console equipped Mustang and Cougar. Casting number is C8OA-18A932-B.

Good chrome, better fit than the reproductions we sell.

Used on the Mercury Cougar or Ford Mustang with a factory center console and measures 1-3/8 inches tall. Replaces part # C8ZA-8A932-B

This is correct for your 1968 non console Mustang or Cougar. Fits left or right, no cracks or peeling. Casting number is C8ZA-18817-E.

Very nice knob with no missing / lifting chrome. If you don't mind some damage on your knob we have plenty that are less than perfect, mention it and we will give you one for free with your order.

This knob is for Cougars equipped with consoles only and then only the earliest of Cougars would have seen this plastic, lower profile, delicate knob. Very hard to find Cougar only knob that is not found on any other model. This is one RARE little dude indeed!Replaces part # C7WA-18817

Reproduction radio knob used on Mercury Cougar or Ford Mustang with a factory center console. Replaces part # C8ZA-18817Fits: 1968 Mercury Cougar

Used on Mercury Cougar or Ford Mustang with a factory center console. Replaces part # C8ZA-18817Fits:1968 Mercury Cougar

Premium grade used outer (tuner / volume) knob with no missing chrome or cracks. Two required per car, sold individually. We also have knobs with peeling chrome, we are happy to throw a damaged knob in for free with your order, just ask! We also have reproduction sets available.Ford part # D1ZZ-18817-A, and Ford casting # D1ZA-18822-AA.

Used wiper knob for any 1968 Mercury Cougar. This detachable knob with set screw is slightly larger than the ones found in 1967. Good condition, will have a small rust pit or two.

Early 1971 wiper switch knob. Master Parts Catalog says before 5-3-1971. Thereafter through 1973, the part number is D1OZ-17513-A.

1971 - 1973 Cougar wiper control switch knob. In early (May 3, 1971) Mercury changed the knob. This is the later knob. Hex shaped knob, good used, may show some minor wear.

This set of knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and...

Perfect set of four radio knobs for your Mercury Cougar or Ford Mustang. Very hard to find with flawless chrome as most are peeling bad enough to cut you if you are not being cautious. Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting # D1ZA-18822-AA for the outer (tuner / volume) knob. D1ZZ-18830-A for the inner (balance / tone) knob, Ford casting # D1ZA-18A932-AA on the inner (balance / tone) knob.*TRIVIA* Did you know that Ford called the outer (balance / tone)...

Good used set of four knobs for your Mercury Cougar or Ford Mustang with a factory center console. These are plastic and much deeper than the non-console version. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 1968-70 AM radios with rear speakers and 1968-70 AM-FM radios, if you need the white spacer we offer it here. Our blow-out price is based on the fact that these are now available new! Knob length 1 1/2"Sleeve length 1 5/16" ...

Complete five piece set for 1967 Cougars with center console. The majority of 1967 model Cougars got this improved design with stronger outer knobs. Keep in mind we have reproduction knobs that will work in place of these. Also keep in mind we will accept your incomplete set of used 67 console radio knobs for a complete set of our 1968 reproduction knobs. Give us a ring for details.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang.  There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

Used " Red " high beam indicator lens for the Mercury Cougar. This is for late 1968 which uses the small housing. The 1967 lens was blue in color. The lens may have a slight arc to it due to the heat from the bulb over time.

Used high beam indicator lens for the 68 XR7 Cougar.

Used " BLUE " high beam indicator lens for the Mercury Cougar. The early 1967 lens was taped to the back of the dash pad. The late 1967 through 1968 used a lens with a small metal housing.

NOS glove box light switch for the 69 - 70 Cougar or the 69 - 73 Mustang.

Reproduction glove box light switch for the 69 - 70 Cougar or the 69 - 73 Mustang.

This very rare part is unique to the 1970 - 1971 CJ and SCJ C6. There was no 390 option in 1970 - 71. Sales were down on the CJ equipped Cougars in 70-71 making this one very hard part to obtain.  We have determined that this part only fits Mercury Cougar and Ford Mustang. Torino and mid sized Ford/Mercury use a different numbered part. Marked D0ZP-D. Ford Part #: D0ZZ-7A256-D. Check out our video on rebuilding your shifter below: ...

This very rare part is unique to the 1972 - 1973 351-4V / 351CJ with C6. We have determined that this part only fits Mercury Cougar and Ford Mustang. Torino and mid sized Ford/Mercury use a different numbered part. Marked D2ZP-AB. Ford Part #: D2ZZ-7A256-A. Check out our video on rebuilding your shifter below: ...

New manufactured Tilt / Tilt-Away cable for any 1968-69 Mercury Cougar or Ford Mustang with factory tilt steering column. All new parts developed by our in house steering column expert DW. Not created from used parts. The cable sheathing will not split or crack over time like the originals.Replaces Ford part number C9ZZ-3E520-A*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

Used Grade A pads are almost a little wrinkled and drawn looking.  We most likely will not be able to provide the color of your choice.

Grade B pads are will be wrinkled peeling away from the base. We most likely will not be able to provide the color of your choice.

Used only in 1968 Manual 3spd and 4spd on non xr7 models and Mustang. Very hard to come by with no splits, burns or cracks. We rarely can supply the color you desire but please let us know your desired color and we will try. Grade A will not have UV ray damage and will look right at home in a low mile car. Satisfaction guaranteed.

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. These are for Standard level interiors only.