Interior

Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads

Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually. 

Fits 1967 - 1973 Standard or XR7

Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.

Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.

Support brace between the bottom of the steel lower dash panel and the cowl top. Fits 1969-70 Mercury Cougar and Ford Mustang with either air conditioning or without air conditioning. Ford part number C9ZB-6504672-A.

One end attaches to the right of the brake pedal support, and the other to the dash panel. Original Ford part number C9ZB-6504510.

Sold as pair on exchange or outright. Only cores with minimal corrosion can be considered for exchange. Ford part number C7AZ-6204144-A, casting number as seen on the backside reads C8AB-6204122-B.  Does not include smaller rod for the sun visor tips.  Sold as a pair.

Reproduction Sun Visor Bracket & Rod for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang. Great quality and fit, left and right use same part, sold separately. Replaces Ford part # C7AZ-6204144-A.

These courtesy light brackets are located on the very outer right and left under the dash. Sold individually, two required per car. Same bracket used on both sides. Replaces Ford part number C9ZZB-13763-A.Fits:1969 Mercury Cougar1969 Ford Mustang

One year only design.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

Core passenger side (right hand) high back bucket seat for the Mercury Cougar. In most cases the foam will be less than perfect and will need to be recovered. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. Perfect for a 1969 Eliminator clone or to make your 1967-68 safer and more comfortable. If you are going to use these high backs in your 1967-69 Cougar, your existing seat...

This listing is for the bottom part of the seat only, which is often what fails. Keep in mind that we do have a repair bracket for the hinge stud on the right hand side of this seat. This listing will save you a lot of money on shipping if you don't need the entire seat.

This listing is for the bottom part of the seat only which is often what fails. This listing will save you a lot of money in shipping if you do not need the entire seat.

This listing is for the upper part of the seat on a low back bucket with headrests (headrest not included). This listing will save you a lot of money in shipping if you do not need the entire seat.

This listing is for the upper part of the seat on a low back bucket with headrests (headrest not included). This listing will save you a lot of money in shipping if you do not need the entire seat.

Fits RH or LH standard interior, sold individually, two required per car. Has correct grain texture and injection molded exactly like originals. Includes metal clip retainers pre-installed as well as the clips themselves. Available in black only, use any solvent based paint to match the color of your interior. These were used on the 69 - 70 (and some 68) Mustangs but only used in 1970 for the standard model Cougar. Replaces Ford part #: C9ZZ-6560762. ...

Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. No rust, grade "A" show quality chrome, originally came stamped ROBBINS - JR - 7600 or HAMILL H-000. If you have a preference as to which version you would like just let us know in the memo box at checkout. Check out our video "All about seat belts" below. ...

Sold as a pair. Two required per car.Replaces Ford Part #: 380239.

Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...

Great Reproduction of an Often Broken Part. This part fits on the bottom of the steering wheel and must be in place to cancel your turn signal on tilt column cars. Used on all Ford products with a tilt column 1967-69. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

Factory original turn signal canceling cam. Originals were molded in white, reproductions are molded in black. Repros also available from us. Without this part that self attaches to the back of your factory steering wheel, you will be turning off your blinkers manually. Click up, click down... *NOTE* We have no good reason to encourage you to purchase this hard to find original over the reproduction, unless you just gotta have it. **NOTE** Need help diagnosing a Cougar turn signal problem?...

Used cap for the index lever tension spring for the Mercury Cougar or Ford Mustang equipped with the tilt/tilt away steering column. Two required per car.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Usually ships in 3-5 business days. Reproduction Automatic Transmission Center Console With Woodgrain Insert and Flat Lid for the 1969 Mercury Cougar or Ford Mustang

Very correct reproduction, injection molded like original with correct grain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with cigar lighter, hinge for compartment lid, cigar lighter with correct knob and chrome mounting plate. While not technically correct for the Cougar, many...

Very correct reproduction, injection molded like original with correct grain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with cigar lighter, hinge for compartment lid, cigar lighter with correct knob and chrome mounting plate. While not technically correct for the Cougar, many...

This is a bare bones console with no lid or insert. It is actually a 1969 console base but can be converted to 1970 by changing out the storage compartment area with a used 1970 storage compartment with no lighter. 1970 owners may want to keep the lighter as it makes for a nice power port that is easier to access than the one on the dash. This is a good value for the person who already has a console but the base has been damaged. Made from ABS plastic that is paintable with any solvent based...

Reproduction teak woodgrain center console insert for the 1969 Ford Mustang. NOTE: These inserts came with enough studs to fit multiple cars. When installing this insert, simply clip off the extra studs you don't need.

Very correct reproduction, injection molded like original with correct Burled woodgrain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, your choice of flat or humped lid, insert designed for cars with automatic transmission, dark walnut bezel (xr7 burl grain is NOW available!) front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with...

Very correct reproduction, injection molded like original with correct grain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with cigar lighter, hinge for compartment lid, cigar lighter with correct knob and chrome mounting plate. While not technically correct for the Cougar, many...

Very correct reproduction, injection molded like original with correct grain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with cigar lighter, hinge for compartment lid, cigar lighter with correct knob and chrome mounting plate. While not technically correct for the Cougar, many...

Very correct reproduction, injection molded like original with correct grain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, triple-humped lid, insert designed for cars with manual transmission, simulated burl walnut bezel (correct for XR7), front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with cigar lighter, hinge for compartment...

Reproduction upper portion to the center console found in the Mercury Cougar or Ford Mustang. This unit is a perfect fit in your Cougar or Mustang and features exact color and texture. It also comes with the front hooks to attach it to the lower base. The center console is a focal point of any cars interior and getting rid of that cracked, broken down old console will make a huge difference! *NOTE* This unit does not come with the ash tray assembly, but they're available used or reproduction. ...

Used upper portion to the center console found in the Mercury Cougar or Ford Mustang.  *When placing your order, please mention in the notes as to which color you need and we will do our best to accommodate. *NOTE* This unit does not come with the ash tray assembly, but they're available used or reproduction. Ford Part Number C9ZZ-6304490 ...

Correct color and texture, includes chromed plastic bezel. We also sell the decal only. This was used on the Eliminator / Decor or Standard Interiors but can also be used on your XR7. NOTE: These inserts came with enough studs to fit multiple cars. When installing this insert, simply clip off the extra studs you don't need.

This is a new reproduction available only in black. Perfect in fit and finish with the only difference from original being it does not have the sprayed on velvet-finish on the inside of the storage box. The correct lighter bezel and receptacle are included.

Used center console storage bin w/ lighter bezel. Original used unit with sprayed on velvet-finish on the inside of the storage box. 

Knob is exact replacement, element is a generic replacement. Exact replacement for 67-68 dash or 69 center console lighter and lighter socket.

Cigar lighter for all 1967-68 Mercury Cougar and Ford Mustang dash ashtray mounted locations. Additionally used on 1969 Cougar and Mustang consoles, console only, not the under dash ashtray unit.

Used cigar / cigarette lighter for the lower dash mounted ashtray unit. 1969 Mercury Cougar and Ford Mustang.

Knob is exact replacement, element is a generic replacement. Socket and element are manufactured by the same company to insure fit. Exact replacement for 1967-68 dash or 1969-70 under dash lighter and lighter socket. Replaces Ford part # C7ZZ-15052 and C6ZZ-15055-B.*Note - Retainer should have a ground lug on it in order to work with 1969 console cigar or cigarette lighters.

Reproduction clevis for the tilt/tilt away steering column equipped Mercury Cougar or Ford Mustangs. This unit attaches the pawl cable to the vacuum motor shaft. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used retaining clip for the adjustment bar in the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. Two required per car, used to hold the tilt position adjustment bar in place.  * While not technically correct, this also will work for 1970 - 1974 Cougar/ Mustang tilt columns. SOLD INDIVIDUALLY*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Used clip for the adjustment tension spring for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.