Interior Fasteners

Ford Part # 379390-s Sold individually

Fits 1967 Standard or XR7

Four per car unless you have a 1968 decor or standard model that has the unique three hole armrest and then you will need six. Replaces Ford part # C7AZ-6224146. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Sold individually # 374212-S

Fits 1967 and 1968 Standard or XR7

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

Front retractor bolt, used in conjunction with two rubber spacer / washers and one washer. The two rubber washers go on either side of the re-tractor mounting hole and the metal washer is against the inner rocker.

Front inner bolt that attaches female portion of the lap belt to the transmission tunnel. Used in conjunction with a silver, fat washer that is slightly cupped.

Inner front bolt, long length to clear sound deadener. Used in conjunction with a thick, gold spacer washer.

Good used original seat belt bolt. There were a few different variations of this bolt, some were stamped with a D with there triangles, some with E and three triangles and others had no stamping at all.

Used to mount the front retractor to the inner rocker panel. Used in conjunction with a large washer. May or may not be marked with a letter "C".

Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually. 

Fits 1967 - 1973 Standard or XR7

Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.

Reproduction Vent Frame Bolt Kit 1967 and 1968 Mercury Cougar and Ford Mustang

Pictured is a complete set of 1967 Hex bolts, spacers and washers. We will make sure they are damage free, rust free, and a complete set removed from the same year of Cougar as yours. There were minor and major changes almost every year so you will want to select the right year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! 

This unique little clip looks a lot like the more common door panel clip but on close inspection you will find it is different. Whereas there are slots for three of these per side, only two per side were installed at the factory.Replaces Ford part number 352775-S100.

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

This clip attaches the rear edge of the Xr7 overhead console to the support bracket. In 1968 the more common door panel clip was used for this application. The door panel clip can also be used for your 1967 model, we recommend the used clip over the new one.

These little clips are what were used to fasten the dash face pad to the dash bezels on a 1968 standard or decor level Cougar. They are very difficult to come by and we have yet to find a suitable substitute. We suggest that if you need more than a few of these clips that you consider using strips of adhesive Velcro in lieu of these clips as Velcro holds the fragile aluminum trim more evenly against your bezels and is easier to install and remove for future maintenance. *NOTE* There are 13 of...

Fits 1967 and 1968 Standard or XR7. This kit is nothing more than common door panel clips instead of the correct, unique 1967 A pillar pad clips or 68 A pillar pad clips . These can be made to 'work', but we highly recommend ordering the correct used clips.For the Correct 1967 A pillar pad clips, click here.For the Correct 1968 A pillar pad clips, click here. ...

Fits 1968 - 1973 Standard or XR7

Reproduction Console Ashtray Bumper for the 1967 Mercury Cougar or Ford Mustang.

Fits 1967 and 1968 Standard or XR7

New chrome finish screws for attaching OEM consoles. Screws fit all stock consoles 1967-73 on Mercury Cougar and Ford Mustang, most any Ford consoles actually. Phillips head oval. 1967-68 consoles use 4 attaching screws, 1969-70 consoles need 6 along the outside, 1971-73 consoles have a total of 8 screws along the outside. These are 1-1/2 inches long like the originals.

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

There are five of these on the RH side that hold your plastic dash to the metal understructure. These also hold on the map light. Sold Individually. Ford Part #: 376642-S. Reference from mercurycougar.net: Best guys to always talk to about Cougars...will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting things...

Bulk pack of 100 oval head phillips screws for door and window crank handles.

Sold individually Zinc (dark silver)

Holds insulation to the firewall. Sold individually, 6 per car. Replaces Ford part # C8ZZ-6501691.

Fits 1967 and 1968 Standard or XR7

Fits 1967 and 1968 Standard or XR7

Fits 1967 and 1968 Standard or XR7

This kit connects the Overhead Console mounting bracket to the roof. Screw heads and clips differ slightly between 67 and 68. Replaces Ford Part #: 519B24, 519B38, 519B46

This kit connects the Overhead Console mounting bracket to the roof. Screw heads and clips differ slightly between 67 and 68. Replaces Ford Part #: 519B24, 519B38, 519B46

This is actually the correct 2 inch screw for the 1968, as opposed to the 1 3/4 inch screw that would have come in the 67. With the added length this screw is less likely to pull out of the firewall than the 67 screw was. Fits Standard and XR7. Sold individually.

Fits 1967 and 1968 Standard or XR7

Fits 1967 and 1968 Standard or XR7

This kit contains 500 hog rings, more than enough for two bucket seats and one bench seat.

Chrome screw used to mount the rear interior panel keeper.Sold individually.

Reproduction master interior fastener kit for the Mercury Cougar Standard. This kit contains 264 fasteners in total. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Armrests (front) Armrests (rear) Scuff Plates (door opening) Sun Visor Brackets Glove Box Catch Glove Box Latch Glove Box Liner Ashtray Liner Seat Stops (front of seat backs) Mirror to...

Reproduction master interior fastener kit for the Mercury Cougar XR7. This kit contains 297 fasteners in total. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Armrests (front) Armrests (rear) Scuff Plates (door opening) Sun Visor Brackets Glover Box Catch Glove Box Latch Glove Box Liner Ashtray Liner Seat Stops (front seat backs) Carpet to Floor (carpet...

Fits 1967 Standard and XR7 Cougars or most Ford and Mercury with inside rear view mirrors. Also used on the 1967 xr7 hash marks located on the rocker.

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

New pan head screws for installing the automatic console shifter bezel. Sold as a set of 4. Used in conjunction with the 3 metal strips to attach the automatic shifter bezel. Correct black pan head Phillips screw. *HINT - The metal strips can be made from any strips of steel, they don't really need the edges folded if you don't cinch them down too tight. Metal strip should be 1-11/16" x 5/8" with a hole in the middle.