Fuel Related Fasteners

This screw / stud seems to always be missing. This screw is just a little longer than stock to accommodate installing the Hi-Po air cleaner. Fits most Autolite carburetors. Size: 4 1/8 inches length 1/4-20 X 5/16-18 threads. Check your thread size on the carburetor, we think that starting in 1969 the Autolite 4300 carburetors had 1/4-20 threads. Please note that this stud has 5/16-18 threads going into the carburetor.  Replaces Ford Part #: 370971-A *Note - Check your carburetor, it will...

Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)

Fuel and brake line fastener kit. Fits all 1967 Mercury Cougar and Ford Mustang with V-8 engines and 2 piece fuel line from tank to pump. Early production 1967 cars used a 1 piece fuel line from the gas tank to fuel pump. Eventually Ford installed 2 piece fuel lines during 1967. This is only for the two piece fuel line.*Note these are for the original and reproduction style fuel lines that were 5/16 thick, which was unique to 1967 production.

Fuel and brake line fastener kit. Fits all 1967 Mercury Cougar and Ford Mustang with V-8 engines and 1 piece fuel line from tank to pump. Early production 1967 cars used a 1 piece fuel line from the gas tank to fuel pump. Eventually Ford installed 2 piece fuel lines during 1967. *Note these are for the original and reproduction style fuel lines that were 5/16 thick, which was unique to 1967 production.

Exact copy of the hard to find original. This two piece clip is used to mount gas and/or brake line to floor pans.

This clip attaches by the driver's side front of the fuel tank opening, and holds the fuel line in place near the sending unit. Used on late 1967 to 1968 cars with the 3/8" fuel line. Early 1967 cars had smaller 5/16" fuel line and different routing (through the transmission tunnel) and did not use this part. The reproduction clip for this application has a different appearance, so we wanted to make these used originals available.

 2 piece fuel line. Kit is for fuel and brake lines under the car. Comes as shown. Quality AMK kit. Fits 1967 Mercury Cougar and Ford Mustang. F-3962

This quality kit contains everything you need to replace the original hardware for fuel and brake lines on your 1968 Cougar or V8 Mustang. It even includes 3 new bolts for the metal protector plate for the fuel line near the left rear wheel. Most of the mounting locations can be seen below: Click on images to enlarge. ...

Replaces Ford Part # 359747-S

Original style wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Replaces Ford Part #: C5ZZ-8287-A.

Used original wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Ford Part #: C5ZZ-8287-A.

This plate attaches the 3/8" steel fuel line under the driver's side rear torque box, as it makes its way from the rear frame rail out to the rocker area. It acts both as a mount and as a protector from road debris. These were used on late 1967 to 1968 Cougars and Mustang with the 3/8" fuel line. Early 1967 cars had smaller 5/16" fuel line, and different routing (through the transmission tunnel), and did not use this part. Mounting bolts included.

This plastic protector sleeve is often missing or broken, but occasionally we come across a good used one. This part attaches just in front of / below the fuel tank on the passenger side, and serves two purposes: it routes the wiring closer to the fuel sending unit without it dangling down, and protects it from road debris This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Reproduction Smog Pump Pully Bolt for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually 

This screw / stud seems to always be missing. This stud is just a little longer than stock to allow installing the Hi-Po / 427 GTE air cleaner. Fit most Autolite 4V carburetors assembly. Zinc plated for years of service. Size: 4 1/2 inches 1/4-20 X 1/4-20 threads.

If your fuel line follows the brake line down the transmission tunnel then you have an early model 1967 and this is the right clip set for you!