Interior Fasteners

Used on all four 1967 belts for a total of 8 per car. Found to be slightly dished on most examples we see.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Used on the retractors.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

Same as 69-73 but with no markings.

Reproduction XR7 Console Fastener Kit for the 1967 and 1968 Mercury Cougar

Fits 1968 Standard or XR7

[No Description Provided]

Reproduction 270 piece interior master fastener kit for the Mercury Cougar that fits both Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Sun Visor Brackets Kick Panels Armrests (front) Seat Back Adjustment Scuff Plates Glove Box Catch Seat Back Scuff Plates Glove Box Latch Ashtray Liner Mirror Bracket (interior) Glove Box Liner Carpet to...

Fits 1968 Standard or XR7

Four per car unless you have a 1968 decor or standard model that has the unique three hole armrest and then you will need six. Replaces Ford part # C7AZ-6224146. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Front retractor bolt, used in conjunction with two rubber spacer / washers and one washer. The two rubber washers go on either side of the re-tractor mounting hole and the metal washer is against the inner rocker.

Rear seat belt bolt, four per car used in conjunction with two red washer / spacers. 13/16" hex head, 1-1/4 inch bolt with a 3/16 inch shoulder. Can be either smooth headed or have a Heavy or Light "A". There is another version of this same bolt with a smooth head and no markings.

Used Vent Frame Bolt Kit 1967 and 1968 Mercury Cougar and Ford Mustang. Consists of: 1 bolt - 379384-S2 1 bolt - 378694-S 2 lock nuts - 33797-S2 set screws -  375694-S2

Two of these clips per side are required to hold the interior padded pillar pads the the "A" pillars on your 1968 Cougar.Replaces Ford part number 381896-S2.

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

These little clips are what were used to fasten the dash face pad to the dash bezels on a 1968 standard or decor level Cougar. They are very difficult to come by and we have yet to find a suitable substitute. We suggest that if you need more than a few of these clips that you consider using strips of adhesive Velcro in lieu of these clips as Velcro holds the fragile aluminum trim more evenly against your bezels and is easier to install and remove for future maintenance. *NOTE* There are 13 of...

Fits 1967 and 1968 Standard or XR7. This kit is nothing more than common door panel clips instead of the correct, unique 1967 A pillar pad clips or 68 A pillar pad clips . These can be made to 'work', but we highly recommend ordering the correct used clips.For the Correct 1967 A pillar pad clips, click here.For the Correct 1968 A pillar pad clips, click here. ...

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Replaces Ford Part #: C0AB-6423240-B. Four required per car, two per side. If your quarter glass is loose in the track and will not roll up and down these rollers are most likely the culprit. When the tracks get gummed up and the window takes too much effort to roll up and down, these brittle old rollers will break. Even if they are not broken they are often frozen in place from rust and will not spin freely. From our experience every 1967 - 1968 Cougar needs these replaced if they still have...

Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.

Used seat belt bolt washer for the Mercury or Ford.

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.