Heating & Air Conditioning

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.

Used stamped steel lateral support bracket for all 1970 Mercury Cougars and Ford Mustangs with the 351 Windsor or Cleveland engine. Ford part # D0OZ-2888-A*NOTE* - Excludes all 1969 351 Windsor engines.

Used steel lateral support brace for Cougars and Mustangs with the 390-2V, 390-4V, or 428CJ FE engines. Identical to the 1970 FE lateral bracket except 1970 versions have square nuts on the reverse.Ford part # C8AZ-2888-A

Used steel lateral support brace for Cougars and Mustangs with 428CJ FE engines. Identical to the 1968-69 FE lateral bracket except 1970 versions have square nuts on reverse. Also the same bracket for Ford passenger car 390 up until 1971.Ford part # D0AZ-2888-B

This little switch is mounted on the back side of your interior temperature control panel on most 1969-72 Ford products. It energizes the A/C pump when you move the the knob to the "A/C" position. Correct dimensions and easy to install. Starting sometime in 1972, this switch was incorporated with the vacuum selector manifold. This is part of the switch assembly C9ZZ-19B888-A.

This little switch is mounted on the back side of your interior temperature control panel on most 1969-72 Ford products. It energizes the A/C pump when you move the the knob to the "A/C" position. 15 AMP micro switch. Starting sometime in 1972, this switch was incorporated with the vacuum selector manifold. This is part of the switch assembly C9ZZ-19B888-A.Tested and guaranteed to work, originally produced by Cherry Electrical Corp.

Cast iron pedestal mount for the air conditioning compressor on all 1970 - 1973 Mercury Cougars and Ford Mustangs with the 351C engine, both the H code 351-2V and M code 351-4V engines. Ford MPC part # D0ZA-2882-C.

Air compressor mounting pedestal for 1969 and 1970 Mercury Cougars or Ford Mustangs with 390 or 428CJ engines. Casting number C9AA-2882-A.Ford part # C9AZ-2882-A.

Used mounting plate for the heater blower motor on the 69 - 70 Cougar or Mustang without A/C.Keep in mind that this same plate can be used on a 67 - 68 Cougar and Mustang heater blower motor with A/C.

This gasket seals the fresh air tube in the cowl to the heater box inlet on 1967 through 1970 Cougars.

Reproduction heater duct nylon rivet #375064-S is sold individually.

Push on retainer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a washer to go against the pinched stops. Probably fits most Ford products, not just 1967-73 Cougar and Mustang.Replaces Ford part number 383358-S.

New push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually. These are all plastic with flush mounted head. Replaces Ford part number 380464-S.

Used push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually.Replaces Ford part number 380464-S.

Air conditioning bearing replacement service. Send your flat bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new flat bearing. Either large or small flat bearings, same price.  Dust caps hand fitted, for seamless installation. No extra tool marks, other than the factory peening. Check photos.Ford casting #'s D0AA-8A617-B, D0AZ-8678-D, C8AZ-8678-B, C8AZ-8678-C, C8AZ-8678-A, D8OH-19W653-A, D0AZ-8678-D.*Note* All new bearings will...

Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1969-73 Cougars and Mustangs, but also on 1968 and newer Fairlanes, Torinos, Rancheros, Cyclones, and Montegos. Also installed on 1970 and newer Mavericks / Comets, plus 1971 and newer Lincolns.Ford part # C8OZ-18591-A.*Note - Excludes Heater with...

New heater blower motor resistor that attaches to the heater blower fiberglass housing. Ford part # C8OZ-18591-A.1970 and Later Maverick and Comet1971 and Later Lincoln

Used OEM Ford heater blower motor resistor for cars with factory installed air conditioning, it attaches to the A/C blower fiberglass housing. Fits all 1969-73 Mercury Cougar and Ford Mustang with integral or factory air conditioning. The reproduction resistor that fits the 1967 - 1968 Cougar and 1965-1968 Mustang has a different hole pattern. According to manufacturer information (INDAK), the OHM output for this switch makes it incompatible with the earlier reproduction resistor. We inspect...

Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.

Correct heater box seal kit for 1969 and 1970 Cougars and Mustangs. Replaces Ford part #: C9ZZ-18500-B. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years.

This kit is designed for the 1969-1970 heater A/C box. Replaces Ford Part #: C9ZZ-18500-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years.

Reproduction A/C discharge service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 3/4" fitting. This valve accepts the R134A connection, not the R12.

Used A/C discharge service valve for 1970-73 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used high pressure or discharge valve for installation on either York or Tecumseh air compressors. Has the 3/4" inch 'O'-ring fitting for discharge hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and...

Reproduction A/C suction service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 7/8" hose fitting. Replaces part # D0AZ-19752-A or D0AA-19752-A.

Used A/C suction service valve for 1970-73 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch 'O'-ring fitting for suction hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.

Shaft or rod for the A/C damper blower door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1969-73 shaft is clocked differently than the 1967-68 version. This air conditioning damper door is in front of the blower or fan in the center of the car. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number...

Shaft or rod for air inlet damper door for any 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C9ZZ-19C774-A.

Shaft or rod for the evaporator damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft has a tab mounted on the lever, and is clocked differently than the 1969-73 version. The evaporator damper door allows air to pass over the evaporator in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related...

Quick disconnect that installs between the sight glass hose and the sight glass to A/C dryer hose. This unit also includes 2 O-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316)Quick Connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252).

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. NOS, new old stock part. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This reproduction A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel.  Save your knobs or consider purchasing the 1969-73 selector button kit, you can find them here.Ford part # C9ZZ-19986-A.

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. We always test all of our electrical components and this is a good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.

C9ZZ-18578-A mounts to the rear of the factory installed heater control ventilation control pane. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1969-73 selector button kit. LINK This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used vacuum actuator for controlling the center A/C vent on certain 1969-70 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Studs are on 1-1/4 inch centers. Common single port vacuum valve is on 2-1/4 inch centers. Ford part number C9ZZ-18A318-A. ...

Reproduction vacuum actuator for controlling dampers and levers on the different year A/C boxes. These came in several different anodized colors. This is the basic valve with a single vacuum port.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors, for 1967-68 the color was brown. This is the basic valve with a single vacuum port.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. Blue is the color found 1969 and 1970 and early 1971. Blue and Brown actuators are exactly the same. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port...

Used extension or rod for the vacuum actuator for controlling the fresh air door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the right hand end, of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting...

Used extension or rod for the vacuum actuator for controlling the air restrictor door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the front of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C9ZA-18...

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

Used vacuum switching manifold and electrical micro switch assembly from a 1969 to early mid 1972 Mercury Cougar and Ford Mustang. This is the all metal version vacuum distribution block. 1972 owners, please check your A/C controller to verify if you have or need the plastic version of this switch. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

Used Grade A Windshield Defroster Nozzle for any 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Grade A will be free from physical defects, may have a minor scuff or scratch.Replaces Ford part number C9ZZ-18490-B.

Used Grade B Windshield Defroster Nozzle for any 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Grade B will have a small crack or chip, or possibly a broken mounting tab.Replaces Ford part number C9ZZ-18490-B.