Dash Related Parts

Reproduction radio knob used on Mercury Cougar or Ford Mustang with a factory center console. Replaces part # C8ZA-18817Fits: 1968 Mercury Cougar

Rare radio knob used only on the 1967 XR7 and standard Cougar console. This knob differs from the Mustang console and Cougar / Mustang non console knob in that it is deeper to clear the console pad that is unique to the 1967 Mercury Cougar. Early standard model Cougars with the console used a more petite version of this plastic knob. Replaces part # C7WA-18817-B

Used wiper knob for any 1967 Mercury Cougar. This version is smaller than the 1968 knob. Unlike the 1968 version, there is no set screw, and is simply pressed into place. You may need to use a bit of adhesive to hold in place. Good condition, will have a small rust pit or two.

Used wiper knob for any 1968 Mercury Cougar. This detachable knob with set screw is slightly larger than the ones found in 1967. Good condition, will have a small rust pit or two.

Used knob for wiper control switch on dash panel. Constructed of metal with chrome, may show some wear on the black painted section and flaws in the plating.Ford part number C9ZZ-17513-C.

Chrome and black knob just like the original.NOTE: This knob is correct for 1969. It will fit on a 1970, however the orientation of the pointer will be off. You can find a good used 70 knob here. Replaces Ford Part # : C9ZZ-17513

1971 - 1973 Cougar wiper control switch knob. In early (May 3, 1971) Mercury changed the knob. This is the later knob. Hex shaped knob, good used, may show some minor wear.

This knob set differs from the set used later in 1967 only in that the outer knob has a lower profile head. Keep in mind we have reproduction knobs that will work in place of these.

This set of reproduction used knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear...

Full set of metal radio knobs for the 1967 Mustang or Cougar. Not for use with the 1967 Cougars equipped with factory center console. Keep in mind we have reproduction knobs that will work in place of these.

Nice clean set of four used radio knobs for your 69-70 Mustang or Cougar. No peeling or cracks. The inset picture shows the used next to the new from the backside. The reproductions are shown on the right. Whereas the repros are nice, the originals are still superior. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. White plastic reproduction spacers available here. The white...

The early Cougars had a lower profile head on the outer knob. It is assumed they beefed up the design in early in the year because the knobs were easily broken. These delicate plastic knobs are very hard to find in this condition. Only the utmost purist would care to obtain a trivial detail part such as these to make their car correct. These deeper knobs were only used in cars equipped with a factory center console. The Mustangs did not have a padded console in 1967 so this set is for 1967...

Complete five piece set for 1967 Cougars with center console. The majority of 1967 model Cougars got this improved design with stronger outer knobs. Keep in mind we have reproduction knobs that will work in place of these. Also keep in mind we will accept your incomplete set of used 67 console radio knobs for a complete set of our 1968 reproduction knobs. Give us a ring for details.

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.

Used " Red " high beam indicator lens for the Mercury Cougar. This is for late 1968 which uses the small housing. The 1967 lens was blue in color. The lens may have a slight arc to it due to the heat from the bulb over time.

Used clear lens for the Oil & Amp gauge cluster found on all 1971-73 Mercury Cougar XR7's. We offer these as replacements, often the UV rays damage the ones on convertibles.Check out the video below on our new gauge tester: ...

Used " RED " belt indicator lens for the Mercury Cougar. This is the early 1967 lens that was taped to the back of the dash pad. The late 1967 through 1968 used a lens with a small metal housing.

Used " Red " belt indicator lens for the Mercury Cougar. This is for late 1967 through 1968 which uses the small housing. The early 1967 lens was taped to the back of the dash pad. The lens may have a slight arc to it due to the heat from the bulb over time.

Used " RED " brake indicator lens for the Mercury Cougar. This is the early 1967 lens that was taped to the back of the dash pad. The late 1967 through 1968 used a lens with a small metal housing.

Used " Red " brake indicator lens for the Mercury Cougar. This is for late 1967 through 1968 which uses the small housing. The early 1967 lens was taped to the back of the dash pad. The lens may have a slight arc to it due to the heat from the bulb over time.

Good used lens, will need polished but no cracks or deep scratches.Check out the video below on our new gauge tester: ...

Good reproduction of a very sought after part. Correct thickness, comes with correct green marker needle. If your current lens is foggy it will not buff out as the problem is internal, not on the surface of the lens. We have been waiting a long time for this one! To remove your clock knob you will need a quality pair of needle nose vise grips gripping the shaft while a second pair of pliers removes the knob by turning it counter clock wise. It is a good idea to put masking tape over the black...

Good used clock dummy lens, will need polished but no cracks or deep scratches. Same lens as official clock lens for 1967-68 Standard Model Mercury Cougar but with the black plastic plug, not an open hole for the clock stem.Ford part number C7WY-10887- Check out the video below on our new gauge tester: ...

Good used lens, will need polished but no cracks or deep scratches. Check out the video below on our new gauge tester: ...

Used XR7 fuel gauge lens. It will need to be polished but will not have deep scratches.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Good used lens, will need polished but no cracks or deep scratches.Check out the video below on our new gauge tester: ...

Used Lens - High Beam Headlight Indicator - XR7 / Standard for the 1969 - 1970 Mercury Cougar. Ford part number C9WY-10A936-A. 

Used high beam indicator lens for the 67 XR7 Cougar.

Used " BLUE " high beam indicator lens for the Mercury Cougar. This is the early 1967 lens that was taped to the back of the dash pad.  The late 1967 through 1968 used a lens with a small metal housing. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in...

Good used lens that has not gone milky from over exposure to the sun. Not for use on the XR7 speedometer or clocks found on the XR7 or Standard models. To get these lenses looking new you will have to use a three step plastic polish like Novus or Meguires plastic polish. If your lenses are cloudy or swirled looking this will not come out as it is internal.Check out the video below on our new gauge tester: ...

Good used lens, will need polished but no cracks or deep scratches. Check out our video on dash removal and restoration below: ...

Good used lens, will need to be polished but no cracks or deep scratches. Check out our video on dash removal and restoration: ...

Used green dash turn signal indicator lens for the Mercury Cougar.Ford part number C9WY-10A936-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Used " GREEN " turn signal indicator lens for the Mercury Cougar. This is the early 1967 lens that was taped to the back of the dash pad. The late 1967 through 1968 used a lens with a small metal housing.

Used green dash turn signal indicator lens for the Mercury Cougar. This is for late 1967 through 1968 which uses the small housing. The early 1967 lens was taped to the back of the dash pad. The lens may have a slight arc to it due to the heat from the bulb over time. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

Used on both the speedometer and tachometer lens. Comes with plastic keeper / washer that connects it from the backside of the lens. Sold individually, two required per cluster. These are in used condition as shown and need restoration. This item may require epoxy. The mounting stud on rear may not be present. It is plastic and originally melted over.

These clips are used to hold the lenses in place on your cluster. Sold as a set of three.

Amps / Fuel gauge lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. There are 3 total retainers needed per bezel, two of this style and one for the temp gauge (they are notched for different placements). Ford called these retainers a 'mask'.Ford part number C7WY-10890- Sold individually, 2 required. NOTE: The amps / fuel gauge retainers have white painted tops,...

Clock and dummy lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Fits any 1967-68 Standard Model Mercury Cougar. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. There are 3 total different retainers needed per standard instrument cluster. Ford called these retainers a 'mask'. Ford part number C7WY-10890-

Speedometer lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Fits any 1967-68 Standard Model Mercury Cougar. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. There are 3 total different retainers needed per standard instrument cluster. Ford called these retainers a 'mask'. Ford part number C7WY-10890-

Speedometer lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. Almost the same as the Tachometer lens retainer, tachometer version has a clipped section shaped like a thumb nail on the edge. Ford called these retainers a 'mask'. Stamped C7WF-10894-S or C8WF-10894-S. Also C7WY-10890- NOTE: The speedometer retainer is different from the tach retainer, the tach retainer is...

Tachometer lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. Almost the same as the speedometer lens retainer, tachometer version has a clipped section shaped like a thumb nail on the edge. Stamped C7WF-10894-S or C8WF-10894-S. Also C7WY-10890 NOTE: The tachometer retainer is different from the speedometer retainer, the tach retainer is notched for the screw post...

Temp gauge lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. There are 3 total retainers needed per bezel, 1 of this style and 2 for the amp and fuel gauges (they are notched for different placements). Ford called these retainers a 'mask'.Ford part number C7WY-10890- NOTE: The temp gauge retainer is painted all black, the amp / fuel gauge retainers have a white...

TEMP / FUEL lens retainer used on the inside of the cluster bezel to shield the face of the gauge. Fits any 1967-68 Standard Model Mercury Cougar. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. This one has a small crescent shaped notch in the rim to fit into the cluster bezel. There are 3 total different retainers needed per standard instrument cluster. Ford called these retainers a 'mask'. Ford part number C7WY-10890- ...

TEMP / FUEL lens retainer, Speedometer lens retainer, and clock retainer - used on the inside of the cluster bezel to shield the face of the gauge. Fits any 1967-68 Standard Model Mercury Cougar. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. There are 3 total different retainers needed per standard instrument cluster. Ford called these retainers a 'mask'. Ford part number C7WY-10890-

Complete used gauge lens retainer set. Used on the inside of the cluster bezel to shield the face of the gauges. Will show a minor amount of wear or rust, plan on cleaning it up and possibly repainting. Ford called these a 'mask'.Ford part number C7WY-10890-

Good used light bar for the convenience control indicator lights on the 1967 Cougar dash face pad. Indicators lights are for belts, door, fuel and park.

This used socket is found on the backside of your instrument cluster and takes a 194 bulb.