Cooling

Generic hose kit that will fit the 289 or 302 for those who are not concerned about the CONCOURS look. Used on both the 20" and 24" wide radiators Replaces Ford Part #'s C4ZE-8260-A and C4ZE-8286-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Available in correct OEM Black. customers looking for a little more flash under the hood might be interested in the highly-polished stainless steel version of this bracket! Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

Factory oil cooler as used on 1969-70 R and Q code Super Cobra Jet 428 engines. Nice used condition, comes as shown with one fitting. Will also work for installing an external oil cooler on the other FE motor applications.Ford part number C9OE-6884-B. 

C5AZ-8509-J For use originally on 1967 289 engines without power accessories. No air conditioning, no power steering, and standard 1 sheave alternators. Single belt pulley 6.10 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.*This is one of the few water pump pulleys that did not have an imprinted casting number. Originally this pulley had an ink stamp. We will most likely be...

Water pump pulley 1 sheave, about 6.11 inches. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches. Application include 1967 Cougar with 289. 1969 Cougar and Mustang with 390-4V. Also various Mustangs 1965-67, all with 289.Replaces Ford casting number C5OE-8509-A.

Single sheave pulley 6-61/64 inches in diameter.Applications:1970 Boss 302 Eliminators without power steering1970 351 engines without power steering1971 - 1973 351 engines without power steering and without A/C.Ford casting number C9OE-8509-E. Ford part number C9OZ-8905-B *Note - this is a very shallow pulley, it is meant to run in the second belt position from the engine. ...

C6OZ-8509-A For any S code 390 engine without power accessories. No air conditioning, no power steering, and standard 1 sheave alternators. Single sheave pulley, 6-3/16 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.Replaces Ford part number C60E-8509-C.

C6AZ-8509-C 390 engines with air conditioning. Power steering and or thermactor emissions allowed. 2 sheaves with a diameter of about 5-5/16 inches. *Notes say after 1-9-1967 engine build date. Ford casting number C6AE-8509-F.

C6AZ-8509-D Strictly California 390 Cougars without air conditioning. With or without power steering. 3 sheave pulley with diameters of both 5-11/16 inches and 6-1/8 inches. Ford casting number C6AE-8509-J.

C8OZ-8509-C 1968 427 / 390-4V without air conditioning and 1968-1970 428CJ without air conditioning. Thermactor on all applications, power steering optional. 3 sheave pulley with two different diameters. The MPC lists it as 6 inches on the dual sheave portion and 5-1/16 inches on the outer but we find the actual outer most measurements to be 6 1/8" wide on the dual pulley and 5 3/16" wide on the single sheave pulley. When laid on a flat surface the height is 2 3/8" tall. Ford casting number...

Used FoMoCo 20 inch small block radiator. This is for a 1967 Mercury Cougar or Ford Mustang with 289-2V, or 289-4V and automatic transmission (code w). Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Factory installed automatic transmission radiators came with the fittings in the bottom tank for transmission cooling. Current listing is dated 7EC or 3rd week of May 1967. Late production date. Ford part number C7ZE-8005-S1 ...

Used FoMoCo 20 inch small block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V, or 302-4V and automatic transmission (code w). Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Factory installed automatic transmission radiators came with the fittings in the bottom tank for transmission cooling. Current listing is dated 8FD or 4th week of June 1968. Very late production date.Replaces Ford part number C8ZE-8005-H1 ...

Used 'CORE" grade radiator, marked C9ZE-D or D1, .. etc. 20 inch used radiator from 1969 Mercury Cougar with Boss 302 or 351W or 1969 Ford Mustang with 302 or 351W or engines. This radiator will have the lower tank for transmission lines. Core grade, likely it has been recored at some point in the last 45 plus years. Limited to stock on hand.Restoring or re-coring OEM radiators is expensive and more for the concours crowd. New or reproduction radiators makes much more economical sense.Ford...

Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and C-6 (automatic code U) transmission. This supplier with the Ford number stamped on the side strap is typically from Dearborn assembled cars. Used core radiator for recoring and restoration. This listing currently has an older replacement 4 tube core. The lower tank has minor damage to the area of the pet cock as shown. Typical Dearborn installed assembly line radiator.Replaces...

Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and manual transmission. Used core radiator for recoring and restoration. This listing currently has a lower tank with minor damage to the area of the hose outlet as shown. Typical Dearborn installed assembly line radiator.Replaces Ford part number C7ZE-8005

Used Western Modine (W/Mo) 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V or 302-4V engines and (automatic code W) transmission. Used core radiator for recoring and restoration. Typical Dearborn radiator, only FoMoCo on the top tank. 1968 Mercury Cougar or Ford Mustang. This is the typical radiator installed at the San Jose, California assembly plant. W/Mo embossed on the top of the tank with a date. Dated 67-10 or October...

Used WMo or Western Modine 24 inch small block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V, or 302-4V and 3 or 4 speed manual transmission. Used core radiator for recoring and restoration. Typical San Jose installed assembly line radiator. Factory installed manual transmission radiators did not come with the fittings in the bottom tank for transmission cooling.Replaces Ford part number C8ZE-8005

Used 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 390-2V or 390-4V and C-6 (automatic code U) transmission. Used core radiator for recoring and restoration. Typical Dearborn radiator, only FoMoCo on the top tank. 1968 Mercury Cougar or Ford Mustang. Replaces Ford part number C8ZE-8005

Used WMo or Western Modine 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 390-2V or 390-4V and C-6 (automatic code U) transmission. Used core radiator for recoring and restoration. Typical San Jose installed assembly line radiator. Dated 67 12. Replaces Ford part number C8ZE-8005

Used FoMoCo radiator marked C8ZE-L1 and dated 8KB, which we believe is 2nd week of October 1968. This is for an early built 1969 Mercury Cougar or Ford Mustang with 390-4V or 428CJ and 4 speed transmissions. Good used radiator for recoring and restoration.Replaces Ford part number C8ZE-8005-L or C8ZZ-8005-C.

Correct core radiator for any 1970 Mercury Cougar or Ford Mustang with the G code Boss 302 engine. Has correct stamped Ford part number on the side strap, and lower tank without fittings for cooling lines. Core grade, will likely need recoring.Replaces Ford part number D0ZE-8005-E / E1

1969 Boss 302 radiator marked C9ZE-AG1 and dated 9EA, we decipher the date as May 1969, first week. The core of this radiator is junk, and will be removed. The upper and lower tanks and side brackets are all good. Fits any 1969 Boss 302 Mercury Cougar Eliminator and 1969 Boss 302 Mustang, it is dated for a May/June 1969 car. *Note - Please call for shipping on this item as it will be shipping from Canada.

1970 Boss 302 radiator marked D0ZE-E1 and dated 9JD, we decipher the date as Sept 1969, 4th week. It has a 3 core construction as shown, with a rebuild tag. The upper and lower tanks and side brackets are all good. Fits any 1970 Boss 302 Mercury Cougar Eliminator and 1970 Boss 302 Mustang, it is dated for a October - November built car. Nice used assembly line, core radiator with original tanks. *Note - Does not have fittings for automatic transmission lines. All Boss 302 cars had 4 speed...

Found on standard cooling and non-air conditioned Mercury Cougar and Ford Mustang 1969 - 1970 all engines. One per car, one on the drivers side of the radiator. *Note - This is a shorter side shield than is found on the 1967 and 1968 Cougar.*Note - Block off plate not needed with the 24 inch radiators.

These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

Made in the U.S.A. by Gates or Goodyear, both suppliers to Ford Motor Co. Upper and Lower Hose that are CONCOURS correct with the correct part numbers stamped on to the hoses as well as the Autolite logo. Replaces Ford Part #: C9ZE-8B274-C & D0ZE-8B273-B.

Original used plastic upper radiator seal for 1971-73 Mercury Cougar and Ford Mustang with 26 inch radiators. Also called a radiator air deflector. Also fits 1970-71 Torino, Ranchero, Cyclone and Montego. As well as 1970-72 full sized Ford and Mercury cars. Comes with 4 original spring clips for mounting. Clips are not sold separately. Plastic portion is about 24 inches long.  Replaces Ford part number D0OB-8B170-B.

New temperature sending unit for the 1970 - 1973 Mercury Cougar and Ford Mustang with an actual temperature gauge. Fits 351C and 351W engines. Temp Sender Switch Temp Rating : 22.7-25.5 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPTF Replaces Ford Part #: D0WY-10884-A (SW-924)Check out the video below on our new gauge tester: ...

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

NOS new old stock Motorcraft water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits 1969 Mercury Cougar and Ford Mustang with 351W-2V, 351W-2V engines. Ford number C9WY-10884-A.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits 1970 351W-2V, 428CJ, and 429CJ engines. 258° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0ZZ-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits 351C and Boss 302 engines. 260° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0WY-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.

195 Degree Thermostat for the 351C, 351M or the 400. Factory spec temp for these engines is 192 degrees. Properly blocks off port that recirculates the water through the engine.

Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. Replaces Ford Part #: D0ZZ-8592-A.

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Dated 2nd quarter of 1967 or 2/67, typical date for 1968 built cars. The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps...

C-4 transmission 90 degree brass fitting for the rear oil cooler line. New reproduction with jamb nut and "O"-ring. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.

Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is correct for all 1968 1969 and 1970 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy demand...

This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...

Vacuum tested working hot water valve for any 1969-73 Mercury Cougars or Ford Mustang equipped with factory A/C. This valve stops the flow of warm coolant in the heater hose, when the A/C is on. Has the original cast brass valve and vacuum pod. Used but functional, the reproduction version is very good, but has a black plastic valve, like the service replacement valves from Ford.Replaces Ford part number C9AA-18495-D.

We have noted the erosion from electrolysis, the rebuilders are capable of filling in the voids. Small block Ford cast aluminum water pump core, suitable for rebuilding. This version has a casting number of C4OE-8505-A. Found on some Ford 260 and 289 engines from 1964-65. Has obliterated casting date as shown. Plan on sending it to a vendor that specializes in water pump rebuilding. See our other core water pump listings for other casting numbers. Two different vendors to...

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C6OE-A. Found on many Ford 289 engines from 1966-67. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other casting...

Direct aluminum replacement for small block 1967 - 1969 cast iron pumps. Probably the last water pump you'll ever buy. Built to cool better and last longer than any other pump. Features state of the art high efficiency impeller with 16 veins and NASCAR roller type bearing. Race proven for reliability and performance. Includes Gasket. Several other websites state that there was a mid-year change in 1969 Cougar's with a 351W, but all the documentation we have and the cars we have on hand...

Dated 6M29, December 29, 1966. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two...