Bumpers & Trim

This one in, one out design was unique to the early 1967 Cougar for the headlights. Also found on vacuum controlled options like the 1967 Mustang Cougar tilt / tilt-away steering column. This is a good used unit that has been tested and found to hold vacuum well. This valve is located a few inches behind the carburetor.

This clip looks just like the larger quarter extension moulding / trim moulding clip, but is smaller (as our comparison picture shows). One clip per side is used to attach the tail end (smaller end) of the moulding / trim to the extension. This unit is also almost exactly the same as the rear deck / trunk lid moulding / trim clip, but this quarter extension clip has a slightly shorter stud. Rarely will the clip you get look as good as the pictured here, usually the "finger" will be missing....

This clip looks just like the smaller rear deck / trunk lid moulding clip but is larger (as our comparison picture shows). One clip per side is used to attach the tail end (larger end) of the moulding to the extension. Rarely will the clip you get look as good as the pictured here, usually the "finger" will be missing. These clips are for the purest where originality is of the utmost importance. If originality is not an issue, you can get our excellent reproduction clip right here and...

Used clip to attach the rear deck / trunk lid moulding / trim on the Mercury Cougar that comes with a reproduction cadmium plated acorn nut. Seven of these clips were used to mount the anodized aluminum 1967-68 trunk lip moulding / trim to the trunk. These clip can also be found on some early 1969 Cougars with a stainless steel deck moulding / trim. This used clip is for our type "A" personality purists that insist on having the original part, even though nobody will ever see it. If ultimate...

NOS rocker moulding end clip. Fits all 1968 Mercury Cougars. This clip is plastic and metal, it has a stud which goes through the body of the car. Sold individually, 4 total needed per car. Our all metal version of this clip is reproduced and is a better value. Find it here.Ford part number C7OZ-6221094-A.

Reproduction rocker moulding / trim end clip for the Mercury Cougar. This clip is a steel clip with a wire like the original. These units are technically for the 1969 and 1970 Cougar, but they will also work well with the 1968 rocker moulding / trim. Four of these clips were used on all 1969 Cougars except for the Sport Special which used two. The 1970 Cougar also uses two per car. Sold individually.Will work on 71-3 with modification. ...

Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...

Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...

Correct plastic rocker moulding clips with Ford engineering # C9WB-6510182-A, Ford part #C9WY-6510182-A. There are five of these on each side for a total of ten per car.Fits: 1969 Mercury Cougar1970 Mercury Cougar

Factory used clip for attaching the long black plastic rear bumper filler on any 1971-73 Mercury Cougar. A total of 8 clips are needed to attach the rear bumper filler. Most have either broken with age, or have broken during the removal of the filler. Sold individually. Limited supply of used, we also stock a suitable reproduction clip. See Related.

Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...

Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...

Set of seven used clips with reproduction stainless steel acorn nuts. These fit the best when using an original aluminum deck lid moulding on a 1967 or 68 Cougar. In 69-70 a stainless deck trim was used and the clip was all metal with no plastic coating. For more insight on this tricky trunk trim, check out our video below: ...

Only for use on standard model Cougars with AC. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

Used grade A dash face pad for the standard Mercury Cougar equipped WITH air conditioning. This unit will be nice and will not have any cracks, but could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different color, find your local autobody supplier. They should be able to mix up a small amount of the exact color you need. This icon means that we're looking to buy this...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used grade B dash face pad for the standard Mercury Cougar equipped WITH air conditioning. This unit will be nice but will have at least one small crack, usually right in the middle. Give us a call to check availability and to find out if we have the color you're looking for. As usual, this pad could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different color, find...

NOS dash face pad for the standard Mercury Cougar equipped WITH air conditioning. This unit will be like new and will not have any cracks. Includes surround trim, but without mounting clips. *NOTE* Attaching clips for this unit are like hen's teeth. We suggest using velcro strips that will secure this unit to your dash. Check out this video

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This rectangular trim part is located on the right side of the glove box on all 1967 - 1968 Mercury Cougars without factory installed AC. This could be referred to as a passenger side AC vent block off plate. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as-is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color.

This restored trim piece mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Driver side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21547-A. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

Left side factory stainless steel door guard.

Left side factory aluminum door guard.

Right side factory stainless steel door guard.

Right side factory aluminum door guard.

NOS aluminum clip on guard for the rear edge of the 1971 - 1973 Cougar driver door. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge.  Ford part number D1WY-6520941-A.

NOS, new old stock, Stainless steel clip on guards for the rear edge of the 1967 and 1968 Cougar doors. Would have been part of the exterior decore option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. Ford part number C7WY-6220910-A.

Stainless steel clip on guards for the rear edge of the 1969 and 1970 Cougar doors. Would have been part of the exterior decor option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. Ford part number C9WY-6220910-A.

NOS aluminum clip on guards for the rear edge of the 1971 - 1973 Cougar doors. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge.  Ford part number D1WY-6220910-A.

Aluminum clip on guards for the rear edge of the 1971 - 1973 Cougar doors. Would have been part of the exterior decor option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. Ford part number D1WY-6220910-A.

NOS aluminum clip on guard for the rear edge of the 1971 - 1973 Cougar passenger door. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge.  Ford part number D1WY-6520940-A.

This restored passenger side (right hand) drip rail moulding / trim has had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as one side only, or as a pair. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used drip rail mouldings / trim. The vinyl top...

Good clean, unrestored moulding with no dings or obvious scratches removed properly from the backside with a hammer and wooden block.Ford Master Part # C7WY-6551726-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we...

These restored driver side (left hand) and passenger side (right hand) drip rail mouldings / trim have had all minor dings and scratches removed and then polished to a mirror like finish. These mouldings have been restored far beyond the quality that your car came with from the factory. These are sold outright, as a pair, or one side only. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used drip rail...

Used Grade "A" center grille emblem for the 71 - 72 Standard Cougar. Most likely will show some fading, no pits. Ford part number D1WY-8A223-A

Pretty safe to say this item will never be reproduced. We often have used in stock but they are always faded.Ford part number D1WY-8A223-A

We only get one of these in every couple of years or so. We often have driver quality emblems in stock. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We...

Faded but good used emblem with aluminum foil background. If you push on the swedged aluminum studs from the backside these will easily remove. The standard grill emblem with a walking cat uses the same stud configuration as XR7 so you can exchange emblems from one to another.

This is the correct emblem that came in the center of the hood moulding on a 1973 Standard model Mercury Cougar. It would not look out of place on an XR7 but of course would not be correct. Ford part # D3WY-16637-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested...

This is the correct emblem that came in the center of the hood moulding on a 1973 XR7 model Mercury Cougar. The price is absolutely ridiculous, I agree. Years ago when they sold for $250 I thought THAT was insane! Replaces Ford part # D3WY-16637-B. Check out this video

New Old Stock grille center extension / surround for the 1970 Mercury Cougar, in the original box from Ford.Ford part # D0WB-16A678-A.

These plastic fillers were mounted to the end of the 1970 hood extension and filled the gap between center grille surround (extension) and the side grilles. Very rare to find a 1970 Cougar with both of these intact as the driver side often got broken when someone reached in the recess for the hood release latch. These feature the original Ford part numbers. Sold as a pair. Disappointing quality, brittle plastic. Unfortunately, used examples are very hard to find, and these are the only new...

These used original plastic fillers mount to the hood extension, and filled the gap between center grille surround (extension) and the side grilles. Very rare to find a 1970 Mercury Cougar with both of these intact as the driver side often got broken when someone reached in the recess for the hood release latch. These feature the original Ford part numbers. Sold as a pair only. Original Ford parts, these will seldom be in stock. Typically the ultra rare driver side may have a defect or small...

These are our average used, or Grade B, front license plate mounting bracket that attaches to the passenger side of the bumper of all 1971-72 Mercury Cougars. It may or may not have the rubber anti rattle bumpers present, but will have either original or reproduction plastic inserts for screwing on the license plate. This B grade bracket will function properly, but will have some slight damage or signs of straightening.Replaces Ford part number D1WY-17A385-A.

Good used 1969 grille center in average condition that will be driver quality or good for rechrome. The grille will look good with the hood closed but when you inspect the backside there may be signs of a professional repair. The chrome will looked aged and may have the beginnings of pits but nothing major. Since this is an expensive part and less than perfect we do not mind sending pictures prior to sending them out. Keep in mind we offer in store credit for broken center grilles even if they...

This grille will be less than perfect with one or two cracks, bend showing and pitting. A Grade "C" WILL be cracked around the perimeter, but will not be missing any pieces. Good for a driver quality car.

This listing is for a BLEMISHED center grille. These blems are for someone on a bit of a budget but still wants the quality of the reproduction. The only problem with these blems is that there will be dings/dents on either side of the emblem area and the paint will be chipped. It will take a bit more than touch up paint to get these in perfect condition, you may have to may have to use a filler if needed. The rest of the grille will have excellent chrome and paint. THE PHOTOS ABOVE WILL...

1970 Mercury Cougar grille chrome pieces. Passenger side, driver side doors, both housings, and the center grille. Technically painted for a standard model, but can easily be detailed for an XR7. Included are the original Ford boxes as shown. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...