Bumpers & Trim

Set of 8 fine threaded Phillips screw assemblies. This the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the...

This fine threaded Phillips screw assembly is the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The two new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the comparison...

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

Set of 8 1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples. Also sold individually.

1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples.Also sold in a set of 8. ...

This bolt is what adjusts your headlamp cover height. Many people do not know they can rid themselves of that droopy eye look (misaligned grille) by placing new rubber pads on the heads of these bolts and adjusting them. Four required per car, sold individually. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

This bolt is what adjusts your headlamp cover height. Rare find to still have an original rubber bumper in place that is not compressed or cracked. Four required per car, sold individually. Check out this video

Anti rattle pad that hooks onto the top edge of the front bumper brackets. These created a soft cushion to prevent the stone deflector from coming into contact with the bumper bracket. These were originally held on with friction tape, same type of tape that Ford used to wrap the wiring harnesses. Sold individually, two needed per car.

NOTE: At the moment the supplier is only making the late model version of this beltline kit. The late version has a slight bend in the chromed quarter piece, whereas the early version is straight (see photo above). Made With Exact Materials As Original. Eight piece kit that includes inner and outer belt-line, enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them...

Driver side headlight door. If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four Phillips...

Driver side headlight door. New Old Stock.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The...

Passenger side headlight door.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the passenger side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four...

Incorrect chrome finish (supposed to be satin not chrome) Mustang part that requires modification to make the metal XR7 insert fit. This is the only new alternative to your broken bezel, we sometimes get in an original that just needs paint. This unit will also fit the Cyclone, Montego, and many other Mercurys and Fords. Replaces Ford part # C8ZZ-3D572-A.

This is the correct horn panel bezel for all 1968 standard model Cougar steering wheels. The satin paint will need to be resprayed but the two mounting studs are in place and there are no cracks or burns. Please see related for XR7 model bezel. Ford part number C8AA-3D754-A.

This is the correct horn panel bezel for all 1968 Cougar XR7 steering wheels. The satin paint will need to be resprayed but the two mounting studs are in place and there are no cracks or burns. Unique to the XR7, identified by having the grey inserts. Please see related for standard model bezel.Ford part number C8AA-3D754-A. * Note - Will not work on standard model Cougar pads without removal of the inserts.

These are 100% correct reproductions for the 1968 Mercury Cougar XR7-G, but will fit any 1967-68 Cougar. These will NOT lay flat against the valance, as the originals did not. These are beveled on purpose and if you attempt to straighten them they WILL break. The reproductions that do lay flat against the valance are no longer being produced. We cannot warranty these against any attempts to straighten them. Sold as a pair. ...

A scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot that did not come out 100%, a slip on the buffer wheel or a pin hole created by over polishing are what you can expect on a blemished piece of trim. We try to carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to... From 10-15 feet away these will look good...

A scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot that did not come out 100%, a slip on the buffer wheel or a pin hole created by over polishing are what you can expect on a blemished piece of trim. We try to carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to... From 10-15 feet away these will look good...

part# 372434-SSold Individually.Head size: 5/8"Thread size: 7/16"

Fits all models.

Bracket tack welded in the trunk to reinforce the rear structure for mounting the rear bumper. Ford part number C7ZZ-17B862-A, fits all 1967-68 Mercury Cougar and Ford Mustang. These are sold individually, these are not side specific. There is also a reproduction version available. Used part cut from a 1967-68 Mercury Cougar, some spot welds will need to be drilled out on your end. Picture shows approximately what you will receive. 

Used front license plate bracket in Grade A condition. Grade A will only need detailing or a fresh spray of chassis black paint. We include fasteners to attach the license plate to this bracket. This bracket mounts to your front valance. Also available in Grade B condition, see related items below. Replaces Ford part number C7WY-17736-A.

This option includes paying a core charge. By choosing this option, the re-chromed bumper you receive will have started the re-chroming process as an average quality core. We highly recommend that you send us your core first. Here's why: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming process as a superior quality core. You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

This is the flat topped rubber bumper that attaches to the top part of your center grille and keeps a small gap between the two panels to prevent paint chips. There were two versions of this bumper, one was this flat topped bumper, and the other had a rounded top. Find the round topped version here.

This little rubber part attaches to the top, flat part of your center grille and keeps a small gap between the two panels to prevent paint chips. This is actually an ash tray bumper but it is a decent substitute (a little smaller than the original) for the center grille bumper. The originals had a flat top as opposed to this bumper which has a rounded top. You can find the flat topped version here. ...

These Grade B Restored bumpers look good on the face, but the backside will have been repaired / reworked and the metal will be thinner than most of our higher quality restored bumpers. This is for the customer on a budget with no core to trade in. Looks and works fine for a daily driver. These bumpers are re-chromed using the triple plating process. This produces a significantly higher quality finished product because they have a layer of copper, nickel and chrome. It is well worth...

This option includes paying a core charge. By choosing this option, the re-chromed bumper you receive will have started the re-chroming process as an average quality core. We highly recommend that you send us your core first. Here's why: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming process as a superior quality core. You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

This bumper bolt is sold individually and replaces Ford part # C4ZB-17758-A. It features the correct "button" head profile covered in stainless steel. Silver zinc with wax coating to extend plating life. Reduced shoulder height allows the nut to seat properly.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more...

C7WY-17767-A Front bumper mounting arm, 1967-68 Mercury Cougar, driver side.

C7WY-17766-A Front bumper mounting arm, 1967-68 Mercury Cougar, passenger side.

Often passenger side brackets have battery acid damage thus the higher price for clean, undamaged passenger side brackets. C7WY-17754-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is...

Sold individually, two required per car. Right is the same as left. These Western rear bumper brackets are not heavily rusted, the threads are in perfect shape and they are not bent. Master part number C7WY-17A750-A.

Good used set of crack free, bend free original brackets. These are Western parts that have never been exposed to road salt and can easily be restored to show quality standards.

This money saving kit gives you all four rubber bumper fillers that wedge into the 67-8 front and rear bumpers horizontally (the triangular ones) as well as the vertical ones that fasten to the leading edge of the fenders and quarters. Keep in mind when you remove the old rubber parts that we can give in-store credit for reusable parts. Please only send us parts that are not ripped, gouged or warped.

Used driver side (left hand) rear bumper guard for the Mercury Cougar. The chrome plating was pretty low quality back in the day and this unit will have some scratches and pitting as it is an almost 50 year old original part. Mounting diagram not included, if you need one CLICK HERE for a printable version. Ford Part #: C7WY-17985-A. *NOTE* Driver side is stamped with an "L" on the backside. ...

Used passenger side (right hand) bumper guard for the Mercury Cougar. The chrome platting was pretty low quality back in the day and this unit will have some scratches and pitting as it is an almost 50 year old original part. Mounting diagram not included, if you need one CLICK HERE for a printable version. Ford part # C7WY-17984-A. *NOTE* Passenger side is stamped with an "R" on the backside. ...

This option includes paying a core charge. By choosing this option, the re-chromed item you receive will have started the re-chroming process as an average quality core.We highly recommend that you send us your core first. Here's why: We can core match your bumper guards. Bumpers guards that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the...

This option includes paying a core charge. By choosing this option, the re-chromed item you receive will have started the re-chroming process as an average quality core.We highly recommend that you send us your core first. Here's why: We can core match your bumper guards. Bumpers guards that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the...

Rear bumper guards and all the parts needed to install rear bumper guards on your 1967 - 1968 Mercury Cougar. Kit Includes:2 Rear Bumper Guards that have been triple plated to a level far beyond NOS standardsthe mounting kit consists of:a reproduction pair of bracketsnew fasteners. Mounting diagram not included, if you need one CLICK HERE for a printable version. No core exchange is required for this purchase. *NOTE* As is often the case, service replacement parts are painted and the...

Reproduction Bumper Retainer for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually 

Hardware for mounting the hood bumpers on the radiator core support. Clip mounts with threads down, nut on top. Sold as a Kit as Pictured.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This check valve is located in-line just behind your carburetor. To test it simply place it in your lips and try blowing through the side with the single port. You should be able to breath in and not breath out. If this valve is bad you will find the headlights opening up after the engine has been shut off on your 1969 - 1970 Cougars and your tilt away function not working correctly on your 1967 - 1970 Cougars equipped with a tilt column. A good working vacuum system should be able to...

Used 1968 Mercury Cougar GT-E horizontal grille bar clip or keeper for the center grille section. This is a rare find, limited to stock on hand.

This trim clip is a little larger than the original C4GB-6242364-A retainer assembly Ford used and looks a little different, but will work just fine for the front extension mouldings. This will also suffice as a good substitute for the 46 clips used on the 1968 GTE side moldings. Sold Individually.Length: 13/16" from lip to lip.

This fragile little clip attaches to the bottom outer edge of the front fender extension and holds the tail of the aluminum eyebrow moulding to the extension, one per side. They almost always fail when you remove them, and to be honest, we rarely have them in stock. We do not list these hard to find parts to tease you, but rather for documentation purposes. We do offer a nice reproduction clip that you can get right here that will work great. ...