Bumpers & Trim

Used passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece will fit right in on your daily driver or is an excellent candidate for those of who like to restore your own parts.Ford part # C5ZZ-6503136-B.

Core anodized aluminum front moulding / trim set for the Mercury Cougar. This is a six piece core set of front mouldings with minor dings and scratches. Good for a poor quality driver or for restoration.  Parts will have no holes, cracks, or heavy pitting.  If you are wanting our six piece restored set and do not have a set to exchange, this listing is what you will need to purchase in conjunction with the restored set.

Reproduction metal trim for filling the gap between the windshield and the dash pads on all 1967-68 Mercury Cougars and Ford Mustangs. This reproduction version is a copy of the 1968 moldings. 1968 mouldings were slightly shorter in length, due to the padded A pillars pads found on Cougar XR7's. 7 attaching screws are included. Ford part numbers C7ZZ-6504522-A and C7ZZ-6504523-A.

This two piece painted trim set helps to secure the dash pad in place at the bottom of the windshield. Fits 1968 Mercury Cougar only due to the larger padded 'A' pillar pads. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color. These 1968 trim pieces also have a slightly textured painted finish, compared to the smooth...

This is the right hand and left hand 1/4 panel moulding. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6529034-A & C7WY-6529035-A.We have found that this 3M product works great for bonding these parts...

Restored three piece anodized aluminum rear moulding / trim set for the rear of the 67-68 Mercury Cougar. These pieces attach to the rear deck / trunk lid and the quarter extensions. New and used clips also available separately. Ford part #: Driver side quarter extension moulding C7WY-6529313-A, passenger side C7WY-6529314-A, deck lid moulding C7WY-6542512-A. *NOTE* Keep in mind that we do give in-store credit for extra core trim and mouldings you may have laying around (from a Cougar of...

Restored three piece anodized aluminum rear moulding / trim set for the rear of the 67-68 Mercury Cougar. These pieces attach to the rear deck / trunk lid and the quarter extensions. New and used clips also available separately. Ford part #: Driver side quarter extension moulding C7WY-6529313-A, passenger side C7WY-6529314-A, deck lid moulding C7WY-6542512-A. If you select this option (paying a core charge), we will randomly select mouldings off the shelf. Paying the core charge does not...

This rear window moulding set has been restored to show quality. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY. Ford part #'s: Driver side upper C7WY-42431-A, driver side lower C7WY-42405-A, passenger side upper C7WY-42430-A, passenger side lower C7WY-42404-A. *NOTE* This unit carries a $200 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit...

This is a set of four rechromed die cast mouldings that attach via speed nuts at the bottom of your vinyl top. These do not pry off! Use your 1/4" drive ratchet with a deep 11/32" socket and small extension. You must remove your rear interior side panels to access the studs for the side mouldings. New speed nuts included, just in case.. If you have extra sets of cores above and beyond the four needed to exchange, we would be willing to give in store credit. Restored moulding will not ship...

This set of four 1967 - 1968 wheel lip mouldings are sold on an exchange basis. If you have extra cores you would like to send in for credit then we would like to hear from you! Please do not send heavily damaged, torn, corroded or kinked trim as the finished product will be delicately thin or not able to be restored at all. Extra screw holes and elongated holes are OK but you will be getting a like product in exchange. We are happy to send your specific cores in for restoration and make sure...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Good set of four, used wheel lip mouldings for your 1967 - 1968 Mercury Cougar. What is considered to be an "acceptable core" is solely at our discretion. If you are in question as to what good cores are, please send quality, in focus, close-up digital pictures to westcoast@classic-cougar.com *NOTE* Some "on the edge" cores that need extra labor can be given a partial credit.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. ...

Restored five piece windshield trim set has been restored beyond the original luster. Keep in mind only cores with minor dings, dullness and scratches can be accepted. Kinked, gouged, and flattened cores will not be credited. This windshield moulding set fits the 1967-1968 Mercury Cougar as well as the 1964 1/2 - 1968 Mustang Coupe and Fastback. Ford part numbers for these pieces include: C5ZZ-6503136-B, C5ZZ-6503137-B, C5ZZ-6503144-B, C5ZZ-6503145-B, and C5ZZ-6503148-D. *NOTE* If...

Good used five piece windshield moulding / trim set as taken from a parts car. Finish will be dull and some pieces may have minor scratches, but overall, this set is ready to install and will look decent as is. Ford part numbers for these pieces include: C5ZZ-6503136-B, C5ZZ-6503137-B, C5ZZ-6503144-B, C5ZZ-6503145-B, and C5ZZ-6503148-D. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. ...

Chromed quarter window moulding or 'hockey stick' mounting bracket for the driver side only of 1967-68 Mercury Cougars. Also attaches the outer window fuzzy or belt line kit component. Stainless steel construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C7WY-6529035-A Check out this video ...

Chromed quarter window moulding or 'hockey stick' mounting bracket for the passenger side only of 1967-68 Mercury Cougars. Also attaches the outer window fuzzy or belt line kit component. Stainless steel construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C7WY-6529034-A Check out this video ...

If your Cougar came from a region that uses road salt your buckets are probably rusted in the corners or worse. Our dry "West Coast" buckets are 100% rust free and the mounting tabs are not broken from the removal of stubborn bolts. They will not be bent or damaged in any way. Keep in mind we do have grade B brackets for much less that only have minor bends or blems that could be easily corrected. *NOTE* These parts are far more important than most people realize. If they structural integrity...

These driver quality buckets are solid but will have a small bend, hairline crack or the beginnings of rust in a corner. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in these brackets are very powerful and if these brackets do...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable.  NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS.   *NOTE* These...

These driver quality passenger side headlight buckets are mostly solid but will have a small bend, hairline crack or the beginnings of rust in the corner closest to the battery. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable. NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS. *NOTE* These parts are far more...

These brackets are required to mount the optional rear bumper guards. They are not an exact reproduction but functionally they are spot on.Installation hardware is hard to come by, so you should hang on to yours and re-use them.Sold as a pair

These are the brackets required to mount the optional rear bumper guards. They mount behind the rear valance and are often overlooked when people part out a Cougar. *NOTE* As is often the case, service replacement parts are painted satin black and the originals installed on the assembly line were left natural. The mounting brackets are in fact supposed to have a natural finish if your car came with them from the factory.

This kit includes all new hardware, and both brackets. Mounting diagram not included (you can save and print the photo above). As shown, 1967 - 1968 rear bumper guards mount 17.5" from the center line of the car. Clip and bolt hardware kit will be new pieces.

This is a 100% accurate reproduction down to the captured lock washer and black Zinc coating. The only difference is that these are made from a substantially better grade of steel than the originals. These often break when you try to remove them to replace the vacuum actuator so if you are planning on doing that procedure we highly recommend buying these in conjunction with the actuators. Sold individually, two required per car. Cougar part number C7SZ-13A173-A. Also Fits: 1967 Ford...

This is the bolt that often gets destroyed when you try to remove it from the bottom side of the headlight bucket. Our West Coast Cougars come apart a little easier so we often are able to pull them with minimal effort. Cougar part number C7SZ-13A173-A. Application includes: 1967-68 Mercury Cougar and XR7, 1967-68 Ford Thunderbird, 1969-71 Lincoln Continental MK III. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in...

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Bumper bolt nuts sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as not to...

New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Check out this video ...

Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.

Reproduction foam rubber donuts that help cushion the brace from the tail panel on any 67 - 73 Cougar or Mustang.Replaces Ford part number C5ZZ-6540996Sold as a set of 4.

If your core is not adequate we have cores for sale. Keep in mind you can get FREE trim parts from us if you have a quantity of good quality cores to exchange!Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. For more info on aluminum trim restoration & core exchanging, check out our video below. ...

This purchase requires you send a good core in advance. If you happen to have a set of three NOS wheel lip mouldings and purchase the fourth as a restored piece from us it will visually fit right in. Restored is never as good as NOS as the polishing process will make the part thinner which means it will be more prone to damage than an un-restored original or NOS trim part.*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by...

Rubber protection sleeve that attaches to the front bumper brace tubes. 1968 Mercury Cougars only due to the front side marker lights. Attaching point is where the front side marker wiring harness touches the bumper brace. Pliable rubber hose slit as shown, about 1-1/2 inch long for those that want to make their own. Looks like 15/16" ID thin wall rubber tubing. Sold individually, two needed per car.

This is the left hand or "Driver Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6529035-A. We have found that this 3M product works great for bonding these parts in place...

This is the right hand or "Passenger Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6551728-A.We have found that this 3M product works great for bonding these parts in place permanently....

New to the market grille fix for 1967 - 1968 Mercury Cougars / Patent Pending. These simple little grille repair clips have been needed since these cars were new! Over the years we have seen a multitude of home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will be listing all the different FoMoCo applications these clips will work on. These clips are sold as a set of four. NOTE: We've found that removing the legs from one side...

Reproduction hood latch return spring, attached to the sides of the hood latch on the 67 - 68 Cougar. Sold individually, 2 required for Cougar, 1 for Mustang.

Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually.NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to apply too much pressure, causing unwanted bending.

Used plastic rocker moulding clip for 1968 Mercury Cougar and 1967-68 Ford Mustang. Used clip, originally pop riveted onto the rockers. Sold individually. Ford part number C7ZB-6510182-A.

Unfortunately the premium version is no longer available.  This version is made of a softer compound than the original bumpers and will not hold up as long as the originals did on a Cougar due to the force that the actuator exerts.  Sold as a Pair. Check out this video Check out this video

Used rubber sleeve from the front outer bumper mounting tube bracket. Must be for anti squeak or for protection of the front turn signal wiring harnesses. One per side, sold individually. The Ford part number for this item is C7WB-17B947-B. These were made from rubber tubing with a wall thickness of 1/8 inch. Inside diameter is approximately 7/8 inch, and about 1-1/2 inches long for these 1967-68 bumper sleeves. Limited to available stock.  ...

New black screws for attaching the headlight doors to all 1967-68 Mercury Cougars. Four screws needed per side for a total of 8 per car. We have found 3 different styles of separate screws that were used during the 1967-68 model run, San Jose and Dearborn may have accounted for a difference. This one matches exactly to one of the more common ones that were installed. Replaces Ford Part number 376352-S15.

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

These are not available new and differ from Mustang. We on occasion find one that is still pliable and intact. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration