All Products

For two spoke steering wheel, comes in black only. Exact reproduction with correct grain texture. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part #D0ZZ-13915.

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems.Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too. ...

This 165 page book has been in the works for over a decade now at Marti Auto Works and it is a must have for anyone purchasing, restoring or researching a 1967-1973 Mercury Cougar, Ford Mustang or Shelby. Even if you are a Mopar or Chevrolet guy, if happen to frequent swap meets and salvage yards you need this invaluable little book tucked away in your tool box or car as you maybe walking right past VERY valuable cars and parts and not even know it... In Kevin's words, "Have you been...

Used C-4 transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1967-68 Mercury Cougar and 1967-69 Ford Mustang cars with transmission code W on the door tag. Cast aluminum construction, the 1968 Cougar version will have the provision for mounting the damper weight on the bottom. Replaces Ford part number C6DP-7A040-A.

Used C-4 transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Cast aluminum construction, the 1968 Cougar version will have the provision for mounting the damper weight on the bottom. 1967 tail shafts with a casting of C6DP-7A040-A will not accept the vibration damper weight. 

Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. D2ZP-7A040-A version also available, we have a good supply of the updated 1972 version. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos.  This housing will not fit full sized Ford Mercury cars that have an FMX,...

Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. C9ZP-7A040-A version also available for slightly more money. Exact same part, just got updated for some engineering or manufacturing reason. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos.  This housing will not...

Internal tail shaft assembly from a FMX transmission. We only disassemble up to what you see in the picture.  *Excludes some FMX transmissions with 351C-4v in 1970. We do not have the larger diameter version available.

Good used driver quality grade "B" bezel with no bends, cracks or deep pits. Chrome will have a decent luster (not perfect), but the paint will need to be redone. If you want show quality then the only way you will be happy is to buy our rechromed bezels. Right and left are interchangeable. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Sold individually, right is the same as left. Needs no repaint in the reflective area and will actually be in much better condition than what is pictured. Seals will need replaced as they are original. Comes with original mounting studs. Great for Shelby or Eleanor clones. Why buy $100 ABS plastic reproductions when you can have original FoMoCo? *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned...

The only difference between grade "A" and grade "B" on this part is the reflective finish on this grade "B" part needs to be redone. There is a spray paint specifically for this application sold by Krylon and others. The pair you get will actually look much better than what is pictured here. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

This pair of sturdy cardboard taillight covers / protectors are designed to protect your taillight sockets from being dislodged or damaged. In addition to the protection they offer they also serve to give a "cleaner" look to your luggage compartment. Will require minor trimming. Please let us know if you have a good used example so as to use as a template to perfect these parts.

Sold as a pair, these cardboard protectors do more than just give your trunk a clean look, they protect your tail light sockets from damage. If you see them advertised for less we want to know about it!

Sold individually, two required per car. This is the same as the 1970 bracket, just different design of clips are used.

This bracket attaches the vacuum storage tank for your headlights to the core support inside the driver fender. It differs from the 1967 bracket in that an oval hole was put in it to allow the socket and pigtail assembly for the side marker light to pass through the bracket located closest to the fender. 1969 uses the exact same bracket except for a slightly different clip design. Sold individually, two required per car. Cougar part number C8WY-13B008-A.

This bracket is used to mount the vacuum storage tank under the driver side fender. Same bracket as was used in 1967 just a slightly different clip. Two required per car, sold individually. Cougar part number D0WY-13B008-A. *Note - The 1967 bracket was used prior to 11/10/1969 built date.

1970 Mercury Cougar hideaway headlight vacuum tank installation brackets (pair) with fasteners. Two different styles of installation brackets for the 1970 vacuum tank found inside the driver side fender. These are tall brackets, the other style utilized 1967 brackets with round spacers.

All parts needed are included to mount your 1970 vacuum storage tank to the core support (backside) under the driver fender. Solid, good original parts found on a Western donor Cougar. Includes short brackets with correct clips, 4 spacers, 4 long bolts with washers, and 4 shorter hex bolts. Typically this kit was used for installing the vacuum tanks until Nov 1969, it is much more convenient to use the more common later kit for the 1970 tank installation.

These tension springs are located on either side of your hidden headlamp eyelids. Our springs are made from the exotic alloy "Inconel". Inconel springs have approximately ten times the memory of the originals which were made from the much more common and inexpensive "piano wire". These springs have been engineered to have the exact same elasticity as the originals but will last decades longer than the originals which from our experience with NOS, usually lose their memory within a year and...

The Big Book is here! This cache of cool Mercury Cougar knowledge features 186 entertaining and informative pages that focus on the 1967-73 Cougar. Don Skinner, former editor at the Cascade Cougar Club, spent 8 years mining valuable data throughout the Cougar community and compiling all of his little gems into "The Big Book." This jewel is chock-full of great tech information, pictures, fun facts, production numbers, rare concept cars and much, much more. Many of the photos and documents...

Here's a new book about the luxury king of classic Cougars, the XR7 G! The book contains many pictures and documents never published before. A great addition to your collection!From the author of The BIG BOOK of Cougar, Don Skinner.

Here's a new book about the king of classic Cougars, the GT-E! This book starts out with the standard '68 Cougar and XR-7 as both models were available with the GT-E option. The reader is then taken through the early stages with the XR-7S and prototypes. Following these pages is the GT-E as we all know it, and then a brief venture into 1969. Lastly are parts lists for the 427 GT-E and the 428 GT-E. This book was written for the casual reader as well as the GT-E enthusiast.The book contains...

Thermactor smog tube installation ferrules. Set of 8 nuts and barrel shaped ferrules.Fits: 1968 Ford and Mercury S code 390-4V engines sold in the US.1968 Ford and Mercury W code 427-4V engines sold in the US. 1968 / 1969 / 1970 428 Cobra Jet engines.1968 / 1969 / 1970 428 Super Cobra Jet engines. ...

Reproduction concours correct premium thermostat for the 351C. This is the correct thermostat you would use in conjunction with the new concourse restrictor / by-pass plate on 70 - 73 Cougars and Mustangs equipped with a 351 Cleveland engine. This is a the assembly line style thermostat.  Replaces Ford part number D0AE-8575-B.

Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:

New water neck or thermostat housing for all 1967-70 Mercury Cougars or most other Fords with 289/302/351W engines. Cast aluminum with a shiny finish as shown. Removable plug for use with thermal vacuum switches. Comes complete with gasket.

Thermostat water neck or 'Connection - Water Outlet' as it is called in the Ford manuals. Fits 1970-73 351C or 351 Cleveland engines as found in 1970-73 Mercury Cougars and most all other Fords with the 351C engine. Cast aluminum housing.*Note - original water necks were cast iron, this is cast aluminum.Gasket not included. Find it here.

New water neck of thermostat housing for most 1967-70 Mercury Cougar or most other Fords with 390/427/428CJ engines. Cast aluminum without casting marks, sand cast finish. Comes with screw-in cap in place of the thermal switch if you like, includes gasket. For use with common 2-1/8 inch thermostats. *Note - very early 1967 cars were still using the 2-1/2 inch thermostats. Cutoff was around November 1966.

Used aluminum water neck of thermostat housing for most 1967-70 Mercury Cougar or most other Fords with 390/427/428CJ engines. Cast aluminum finish. Comes with threaded hole for either a screw-in cap, or thermal switch. For use with common 2-1/8 inch thermostats. Correct for 1968-70 FE engines. Not going to lie, these will show some signs of electrolysis on the inside and where the hose slips on. Additionally, we notice that the threads get a bit rotted out where the thermal switch...

Reproduction aluminum cast A356 water neck for FE Big Block engines. Made from original factory blueprint, and includes the correct stamping. Will fit the 67 Big Block, but markings are correct for 68. Replaces Ford Part #: C8AE-8592-B.

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine.Cable length 22.50 inches long.  *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine. Cable length 24 inches long, check your application. There were size differences between the 2V and the 4V engines. Replaces Ford part number D3ZZ-9A758-C. *Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that date, I think it was much earlier, than July 1972. ...

Cable length 22.50 inches long. Has clevis and pin on the end for attaching to the throttle pedal assembly. *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang H code 351-2V engines. Cable length 23-3/4 inches long. Uses a green plastic bushing to attach to the throttle pedal. We believe that the MPC is wrong on the length. Our observations are that the 2V cable is longer than the 4V version.Replaces Ford part number D3ZZ-9A758-B.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...

Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang Q code 351-4V engines. Cable length 23 inches long. Identified by the blue plastic bushing on the throttle pedal end of the pedal. We believe that the MPC is wrong on the stated length, the 4V cable is shorter than the 2V version.Replaces Ford part number D3ZZ-9A758-C.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...

Ford part #: C9ZZ-9A758-A. All V-8 engines. The plastic portion that is designed to cover the cable at its furthest point by the carburetor will be broken. This is how the vast majority are for 1969, very rare to find a perfect one. Notice there are two versions for 1969, one has a plastic connector that mounts to the firewall and the other version is metal.

This is a damaged but functional part. The plastic will be broken near the end thus exposing the cable.

Replaces Ford part #: C9ZZ-9A758-A.  This updated Throttle cable is decent quality. Thicker stranded cable, correct dimensions with a good fit. A basic replacement cable. Approximately 23" in length.

Reproduction throttle cable for the 1970 Cougar or Mustang. Replaces Ford part number C9ZZ-9A758-E

Kit comes complete with accelerator linkage rod, bushings and clip kit and return spring. Replaces Ford Part #: C5ZZ-9A702.

Accelerator pedal assembly that mounts to the engine firewall. For use with any 1969 Cougar or Mustang WITHOUT factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. Ford part number C8WY-9A702-A *Note - Before 12/11/1968. *Note - not for use with factory cruise control.

Concours Correct Throttle Linkage Rod, 13 1/2" long, S code 390-4V, W code 427-4V, and R code 428CJ with factory 4 barrel HOLLEY carburetor, with out speed control.Replaces Ford Part # C8ZZ-9A702-A