All Products

429 Cobra Jet and top loader 4 speed transmission. Shaft diameter 3 inches, length 53-13/16 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

428CJ engines with C6 automatic transmissions. Shaft diameter 3-1/2 inches. Length 49-41/64 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

This version of the emblem was actually used on early 70's full-size Mercurys, and is almost identical to the 1969-70 version used on Cougars. In order to use it on a Cougar fuel door, the studs on the back will need to be trimmed down The only visible difference is the thinner / more numerous ridge lines in the red crest area than on the Cougar version. Casting number on this substitute emblem is D1GB-16607-AA.The original emblems were never sold as a stand alone part from Ford but rather an...

Pretty safe to say this item will never be reproduced. We often have used in stock but they are always faded.Ford part number D1WY-8A223-A

We only get one of these in every couple of years or so. We often have driver quality emblems in stock. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We...

This is the correct emblem that came in the center of the hood moulding on a 1973 Standard model Mercury Cougar. It would not look out of place on an XR7 but of course would not be correct. Ford part # D3WY-16637-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested...

Very rare more common version of the XR7-G steering wheel gold plated emblem. This is very different from the run of the mill used emblems we have all seen with the brass electro plating worn off. The burnished version was apparently done first: Ford part number S8WS-3849-A and this much more common gold version done second which carries a Ford / Shelby part number of S8WS-3849-B. To learn more click here  ...

Original engine frame mount brackets for all 1971 to 1973 Cougar *convertibles regardless of engine and all 1971 Cougar 429 Cobra Jets. Includes one each: D1ZZ-6028-A & D1ZZ-6029-A engine frame brackets. Visually, there are also a version where there is a double set of holes on top. *Excludes non-convertibles with 351 cubic inch engines.

This is a rare find... This used 4 piece bracket set was taken from a June 17th built 1968 390 X code Cougar with factory dual exhaust. These are much cleaner used parts than you will see in other regions as they have never been exposed to road salt. We no longer sell them with the bolts and clamps, this is a sample photo of one of several sets we have in stock as of 10-12-07. The parts you receive may actually be in better condition except for the rubber parts which are often worse. The...

D0AE-9430-A 351-2V Cleveland engine, factory original cast iron exhaust manifold for passenger side. At some point there may have been a D0AE-9430-F casting number used, which may be substituted as per the Master Parts Catalog. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum intakes such as one offered by Edelbrock.

D1OE-9430-AA 351-2V Cleveland engine, factory original cast iron exhaust manifold for passenger side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum intakes such as one offered by Edelbrock.

D2OE-9430-BA 351-2V Cleveland engine, factory original cast iron exhaust manifold for passenger side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some after market aluminum intakes such as one offered by Edelbrock.

D0AE-9431-B 351-4V Cleveland factory original cast iron exhaust manifold for driver side. At some point there may have been a D0AE-9431-F casting number used, which may be substituted as per the Master Parts Catalog. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

D1ZE-9431-B 351-4V Cleveland factory original cast iron exhaust manifold for driver side. At some point there may have been a D1ZE-9431-BA casting number used, which may be substituted as per the Master Parts Catalog. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

D0AE-9430-B 351-4V Cleveland factory original cast iron exhaust manifold for passenger side. At some point there may have been a D0AE-9430-G casting number used, which may be substituted as per the Master Parts Catalog. Same manifold 1970-1973. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

C7OE-9431-A Factory original cast iron exhaust manifold for driver side. 1967, 1968, and 1969 390/427 left side manifold remained unchanged for all three years. Includes 1968 X code 390-2V Premium fuel cars. Click on images to enlarge. ...

Factory original cast iron exhaust manifold for the passenger/right side and is probably a mid-year change for 1967. For both S & X code 390 engines and W code 427 GT-E engines up until 2/15/1968. Butterfly spacer not included. Ford part # C7OE-9430-C.

C6OE-9428-A 390-4V factory original cast iron exhaust manifold for passenger side. Even though the photo shows a chamfer where an exhaust donut would go, the proper 1967 manifold would have been cast flush, and a butterfly spacer would have been used. The spacer had a flapper that partially blocked the pipe and allow heat to be dissipated upwards to the choke. Spacers not included. We suggest purchasing the later version of manifold that did not use the spacer. *Note, a spacer may be needed if...

351 Cleveland factory cast iron 2V exhaust manifold set, both correct right D1OE-9430-AA and left D1ZE-9431-AA side matching exhaust manifolds.

351-2V Cleveland, factory cast iron 2V exhaust manifold set, both correct right D2OE-9430-BA and left D1ZE-9431-AA or D3AE-9431-AA side matching exhaust manifolds.

351 Windsor factory cast iron exhaust manifold set, both a correct right C9OE-9430-B and left C9OE-9431-B side matching exhaust manifolds. Same manifolds used on all 351 Windsor engines in 1969 and 1970.  No extra charge to look for a date coded pair but no promise we can hit it spot on either.  

This shroud was what Ford would have sold you in the later years up until they discontinued them in the late 1990's. It has the original Ford part number just like the original but is made of a different material and is black instead of dark brown.Ford part number C9OZ-8146-A

Used original fan shroud for the 24" radiator found on Mustang, Torino and Cougar with AC or for Cougars that need extra cooling capabilities beyond what the 20" radiator / shroud can deliver. Shround will have minor damage as shown. NOTE: This shroud will fit on the 67, but will only work on small block Cougars that have been retrofitted with a 1968 - 1969 24" small block radiator and mounts. Ford part # C9OZ-8146-A For some helpful tips on upgrading your Cougar (or Mustang) cooling...

Used Grade "A" condition floor mat set for the 67 - 73 Cougar. Front and rear set.Ford part numbers:Two Piece Front - C7WY-6213056Two Piece Rear - C5ZZ-6513106

New Old Stock Ford flywheel. 11 inch clutch, 164 tooth ring gear,12-3/8 inch bolt circle for clutch pressure plate. Cast iron with C5AE-A and C7TE-A. New, never installed Ford manual transmission flywheel. Fits 351W, 351C, and 351CJ. Ring fear installed, factory fresh.

Used OEM Ford 428 Cobra Jet manual transmission flywheel. Stamped C8OE-A. Needs a ring gear, has chipped teeth. No visible issues, no discoloration from heat. Ford 428CJ only, not for 428 SUPER COBRA JET engines. This flywheel on a 428CJ is externally balanced. Should have 184 ring gear teeth.Ford part number C8OE-6380-A.

This XR7-G Lucas Square 8 light is in average condition with pitted glass, missing plug ends, and pitted spacers. *NOTE* The lens shown is actually mounted upside down for Cougar use.

Original OEM light found on 1968 XR7-G and early cars and later recalled. EXACTLY 100% correct with the right serial numbers in the right places as per the blueprints from Shelby American: * IGM 1642 PN on the bottom right * K11123 N14 cm AUF 5m up the right side * No numbers on left side Marchal made several versions of this light, only this one is the correct one for your 1968 Cougar or Shelby Mustang or California Special (GT/CS). It has the famous 'cat eyes' internal diffuser. Dual...

Core bench seat for the 1968 Mercury Cougar or Ford Mustang equipped with decor interior. 1968 bench seat without optional headrests, but with seat seat back release latches. The foam will almost always be deteriorating or even missing. All seat cores will be solid frames taken from a Western parts car. Keep in mind 68 and 69 are identical except for how the head rests attach. You can easily add head rests from 69 buckets and bolt them to a 68 pair of buckets or bench if you have all the...

Used core bench seat taken from a Western parts car. Will need new foam and upholstery, but solid and complete with headrests. If you would like to put this in a 68 they are in fact identical once the 1969 single post headrests are removed. Does not include seat tracks.

Factory 15/16" sway bar for all GT-E 427-4V, 428 Cobra Jets, 428Super Cobra Jets, and Boss 302 Eliminators. Factory identified with a single 'Green' and single 'Yellow' paint stripe. We also carry the spacer plates separately. *Trivia - 1970 was the first year that a rear sway bar was available on a Cougar. A 5/8 inch rear sway bar would have been included with the competition handling package in 1970. This factory used front sway bar, does not include any mounting brackets or end link...

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1971 Mercury Standard model Cougars and all Ford Mustangs with 22 gallon fuel tanks. This is an original 1971 fuel sending unit that has a return fuel line, and with two electrical prongs. Ford casting number D1ZF-9275-B, master parts catalog number D1ZZ-9275-B. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with...

New Old Stock NOS fuel sending unit for Standard Model 1970 Mercury Cougar or Ford Mustang, all without low fuel indicator. New in the box Fuel Sender with part numbers D0WF-9275-A and D0WY-9275-A. Yes, sometimes there is a Cougar part on a Mustang. Single pin connector, not for use with XR7 models.Check out the video below on our new gauge tester: ...

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1971 Mercury Cougar XR7 with 22 gallon fuel tanks. This is an original 1971 fuel sending unit that has a return fuel line, and with 3 prongs (2 electrical and 1 alignment prong). Ford casting number D1WF-9275-B, master parts catalog number D1WY-9275-B. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar Standard models without...

Good used 1969 grille center in average condition that will be driver quality or good for rechrome. The grille will look good with the hood closed but when you inspect the backside there may be signs of a professional repair. The chrome will looked aged and may have the beginnings of pits but nothing major. Since this is an expensive part and less than perfect we do not mind sending pictures prior to sending them out. Keep in mind we offer in store credit for broken center grilles even if they...

This grille will be less than perfect with one or two cracks, bend showing and pitting. A Grade "B" will not be cracked around the perimeter and will not be missing any pieces. Good for a driver quality car. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in...

This listing is for a BLEMISHED center grille. These blems are for someone on a bit of a budget but still wants the quality of the reproduction. The only problem with these blems is that there will be dings/dents on either side of the emblem area and the paint will be chipped. It will take a bit more than touch up paint to get these in perfect condition, you may have to may have to use a filler if needed. The rest of the grille will have excellent chrome and paint. THE PHOTOS ABOVE WILL...

Reproduction halogen headlight conversion kit. Included in this kit are the four halogen headlight bulbs (2 high and 2 low) and the full relay kit, which is needed when installing halogen bulbs on your 67 - 68 Cougar. The 55 Watt Xenon Halogen H4/9003 bulbs included in this kit are "cool white" which have a bit of a blueish tint, like you see on modern cars. If you would like to go with a more original "natural white" color, you can buy these inner replacement bulbs. NOTE: YOU MUST BEND THE...

Includes the two muffler hangers and two tail pipe hangers. Will not be overly rusty and will have decent rubber still intact. This set is for any 1969 Cougar equipped with factory equipped dual exhaust.

Includes the two muffler hangers and two tail pipe hangers. Will not be overly rusty and will have decent rubber still intact. This set is for any 1970 Cougar equipped with factory equipped dual exhaust. *NOTE* The 1970 tail pipe hanger differed from earlier years in that the tail pipe clamp was spot welded to it. Our sets usually do not have the clamp still in place as is evidenced by the drivers side tail pipe hanger in this photo.

Ford casting number C8AE-6316-C Includes all 1969-70 Q or R code 428SCJ engines or those cars with the drag pak option. The C8AE-6316-C harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7-1/2 inches. Ford part number C8AZ-6316-C. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for...

Ford casting number C4AE-6316-A. All 1967 S code 390-4V engines. 1967 only, 6-5/8 inches in diameter, cast iron construction with key way groove. This is a combination crankshaft balancer and pulley. Has the timing marks on rim. Ford Master Part number C3AZ-6312-E. Refundable $80.00 core charge when rebuildable C4AE-6316-A harmonic balancer is received by WCCC.*Note - This harmonic balancer is generally covered up by an outer crankshaft pulley when options such as air conditioning and power...

Good used headrest with no mounting hardware included. No cracks. We never have more than one of these in stock as a single so we most likely will not be able to produce the color of your choice but it never hurts to ask! Basic Ford part number for this item is C8AB-62611-A08. The "08" suffix part of the number may refer to a specific color.

This used header will be as good as you can get and it can be restored with some TLC. The part you get will be solid with minimal or no corrosion. Ford casting number C9ZB-76514A72-A

NOS grille headlight eyelid door vacuum actuator for the Mercury Cougar. No exchange needed for NOS. *NOTE* While original FoMoCo boxes are fun and all, we do not recommend you invest in these units as shown with the multiple crimps at the top. These later dated service replacement units shown here were made out of country and are inferior to what the OEM supplier made back in "the day". The rubber elasticity is not as good as the early units and the porosity of the metal makes them impossible...

NOS Ford replacement driver side headlight housing for the 1971 - 1973 Mercury Cougar. The 73 headlight housing will fit on 71 - 72, but not vice versa. This is a new in the box original replacement part that inludes the headlight cups and rings. Ford part number D3WY-13008-B

Used A grade, passenger side or right hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our A grade housings may a minor chip, but will not have damage where the housing bolts to the car, or where the headlights mount. Fits all 1971-73 Mercury Cougar. This 1973 fiberglass passenger side headlight bucket also fits 1971-72, but not vise-versa.Ford part number D3WB-13099.

NOS Ford replacement passenger side headlight housing for the 1971 - 1973 Mercury Cougar. The 73 headlight housing will fit on 71 - 72, but not vice versa. This is a new in the box original replacement part that inludes the headlight cups and rings. Ford part number D3WY-13008-A