1969 Mercury Cougar

Reproduction passenger side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability,...

Good clean used passenger side (right hand) brake spindle for your Mercury Cougar or Ford Mustang equipped with front drum brakes. Cars with disc and drum brakes used the same spindle in 1967, but this spindle was carried over through 1969 on drum brake cars only. Bearing surface measurements: 0.75" and 1.25". We check these very closely, and if they are not perfect, we chuck'em into the scrap pile. All have a Ford C6O... casting number.Ford part # C9OZ-3105-C. Check out this video ...

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The benefit of using this foam float, is that sometimes the hollow brass float will leak, causing a bad reading. This foam version of the float is fuel resistant and will never leak. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The problem with these brass floats, is that after year of being in contact with fuel, they will begin to corrode and disintegrate. We suggest going with the new foam floats. They are fuel resistant and will last longer. Find it here. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

Core passenger side (right hand) high back bucket seat for the Mercury Cougar. In most cases the foam will be less than perfect and will need to be recovered. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. Perfect for a 1969 Eliminator clone or to make your 1967-68 safer and more comfortable. If you are going to use these high backs in your 1967-69 Cougar, your existing seat...

This listing is for the bottom part of the seat only, which is often what fails. Keep in mind that we do have a repair bracket for the hinge stud on the right hand side of this seat. This listing will save you a lot of money on shipping if you don't need the entire seat.

This listing is for the bottom part of the seat only which is often what fails. This listing will save you a lot of money in shipping if you do not need the entire seat.

This listing is for the upper part of the seat on a low back bucket with headrests (headrest not included). This listing will save you a lot of money in shipping if you do not need the entire seat.

This listing is for the upper part of the seat on a low back bucket with headrests (headrest not included). This listing will save you a lot of money in shipping if you do not need the entire seat.

Core passenger side (right hand) bucket seat for the Mercury Cougar or Ford Mustang. This unit will include the headrests. However, in most cases the foam will be less than perfect and will need to be recovered. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. Seat hinge covers and hardware available separately. *TRIVIA* In 1969, the only way to have gotten high back bucket...

Core driver side (left hand) bucket seat for the Mercury Cougar or Ford Mustang. This unit will include the head rests. In most cases the foam will be less than perfect and will need to be recovered. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. Seat hinge covers and hardware available separately. *TRIVIA* In 1969, the only way to have gotten high back bucket seats in you...

Core driver side (left hand) and passenger side (right hand) pair of bucket seats for the Mercury Cougar or Ford Mustang. These units will include the headrests. However, in most cases the foam will be less than perfect and will need to be recovered. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. Seat hinge covers and hardware available separately. *TRIVIA* In 1969, the only...

Fits RH or LH standard interior, sold individually, two required per car. Has correct grain texture and injection molded exactly like originals. Includes metal clip retainers pre-installed as well as the clips themselves. Available in black only, use any solvent based paint to match the color of your interior. These were used on the 69 - 70 (and some 68) Mustangs but only used in 1970 for the standard model Cougar. Replaces Ford part #: C9ZZ-6560762. ...

Grade A XR7 used bucket seat vinyl trim panel. Available in 1969 1970 interior colors. Please specify in the notes your desired color. Grade A will not have cuts or tears, there may be slight impressions in the vinyl or a warped backer board. Driver and passenger side are the same, sold individually. Typically these would have had a basic Ford part number of 60762. XR7 panels have the map pockets on the back. The elastic may be stretched on these.  We also have B grade used panels...

Grade B XR7 used bucket seat vinyl trim panel. Available in 1969 1970 interior colors. Please specify in the notes your desired color. Grade B will have cuts or tears, there may be slight impressions in the vinyl or a warped backer board. Driver and passenger side are the same, sold individually. Typically these would have had a basic Ford part number of 60762. XR7 panels have the map pockets on the back. The elastic may be stretched on these.  We also have A grade used panels too,...

Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. No rust, grade "A" show quality chrome, originally came stamped ROBBINS - JR - 7600 or HAMILL H-000. If you have a preference as to which version you would like just let us know in the memo box at checkout. Check out our video "All about seat belts" below. ...

Reproduction 1156 Back Up Light Bulb for the 1969 - 1973 Mercury Cougar

Brand new 1157 (dual-filament) exterior stop lamp / turn signal light bulb for the Mercury Cougar or any vehicle equipped with 1157 bulbs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. For even brighter...

The 67 -73 Cougar uses the 1157A (Amber) bulb for the turn signals.  This bulb will also fit other applications that require an 1157A or 1157NA bulb. Replaces bulb #: 1157A or 1157NA

This bulb fits several applications including the door panel courtesy lights in the 1967 - 1968.

New 1891 bulb for the 1967-68 XR7 overhead console. This bulb will also fit the 67 - 68 rear console light. You can find the LED version of this bulb here.

New 1895 bulb for the instrument clusters. *Note - The table and the owners manuals are wrong for the Visual Check Panel bulbs, Ford literature calls out a 1895 bulb, when in fact the correct bulb is 1891.

Reproduction 194 light bulb that can be used for your gauges, high beam indicator, clock, or turn signal indicators for the Mercury Cougar.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Reproduction 257 Door Ajar / Park Lamp Light Bulb for the1969 and 1970 Mercury Cougar

Reproduction 631 Glove / Luggage Compartment / Under Dash Courtesy / Trunk Light Bulb for the 1967 - 1973 Mercury Cougar

This listings is for the rubber bump stop used on the headlight housings of the 69 - 70 Cougar. The purpose of this bumper is to stop the eyelids from hitting bare metal when they open up. As the years go by, these bump stops will become heavily indented and may need replacing. There are a few reproductions out there that are "close enough" but so far we haven't found a good match. 1970 has two per side, four per car.  1969 has one per side, two per car. See reference photos above. ...

Concours correct reproduction with correct red finish exact to original Ford part number c8oz-7583-a specifications

Used rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors. Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B  Check out...

One used anti rattle spacers / guards that go between the fender and the cowl on each side. The majority of 1969 Cougars and Mustangs used a black foam block glued to the cowl but in late 1969 and all of 1970 these wedge shaped rubber parts were used. Replaces Ford part number C9ZZ-16758-A.

Pair of anti rattle spacers / guards that go between the fender and the cowl on each side. The majority of 1969 Cougars and Mustangs used a black foam block glued to the cowl but in late 1969 and all of 1970 these wedge shaped rubber parts were used. Replaces Ford part number C9ZZ-16758-A.

Reproduction cowl cover to hood rubber bumpers for the Mercury Cougar or Ford Mustang. These little units attach to the front of the cowl cover for the back corners of the hood to sit on. These will also work for the 1967-68 Mercury Cougar or Ford Mustang fuel filler door bumpers if you are missing them. Sold as a pair and comes with the attaching screws. *NOTE* These are not an exact replacement, rather a part from another year and application that has been found to be an adequate...

Mounts to the bottom lip of the coil spring cover, two required per car, sold individually. Replaces Ford part #: C6OZ-3020-A.

Sold as a pair. Two required per car.Replaces Ford Part #: 380239.

This is the rubber that goes into the bracket of the bottom of the center of the door, for 1969 or early 1970 Mercury Cougar and Ford Mustang with glue-in door glass. This bumper will not work if your door glass is the 1970 bolt-in glass. We also sell the version for the 67-68 and late 1970 bolt in glass.Ford part # C9ZZ-6521762-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for...

This is the rubber that goes into the bracket of the bottom of the center of the door, for 1969-1970 Mercury Cougar and Ford Mustang glued-in door glass.  Note that this bumper is substantially shorter than the 70  bolt-in door glass version.   See D0ZZ-6521762-A for the 1970 bolt-in door glass version.  If you are swapping out a door on a 69 or a 70 don't forget that the door glass is different between the years and, if you have to swap out the glass, you will...

Exact fit for the front license plate brackets, will also fit the rears, but not concours.

Sold individually, two required per car. Replaces Ford part # C3DZ-4730.

Mounts over rear axle ends into the body/frame, two required per car, this is the more pointed Christmas tree shaped version.Ford part # C6AZ-4730

Rubber bumper used on 69-70 taillight housings to cushion the closing of the fuel door, sold individually, two required per car. Replaces Ford Part #: 16758.

Here is a time and money saving package deal for the person restoring their 1969 Cougar. This package includes: Hood lip moulding Fender extension mouldings Deck / Trunk lid moulding Six Piece Convertible Windshield Trim Kit Front and Rear Award Winning Bumpers Keep in mind we will often give extra core value trade in for items we may be low on. Please call before sending extra parts for trade value. All parts are show quality. The bumpers are triple plated chrome, the aluminum has the correct...

Here is a time and money saving package deal for the person restoring their 1969 Cougar. This package includes: Hood lip moulding Fender extension mouldings Deck lid moulding Drip rail mouldings Nine piece front and rear window trim Front and rear Award Winning Bumpers Keep in mind we will often give extra core value trade in for items we may be low on. Please call before sending extra parts for trade value. All parts are show quality. The bumpers are triple plated chrome, the aluminum has the...

This bumper bolt is sold individually and replaces Ford part # C4ZB-17758-A. It features the correct "button" head profile covered in stainless steel. Silver zinc with wax coating to extend plating life. Reduced shoulder height allows the nut to seat properly.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more...

C9WY-17767-A Front bumper mounting arm, 1969 Mercury Cougar driver side. This will work fine on 1970 Cougars, but technically the 1970 bracket has a rectangular hole for a anti rattle piece of rubber for the stone guard.

C9WY-17766-A Front bumper mounting arm, 1969 Mercury Cougar passenger side. This will work fine on 1970 Cougars, but technically the 1970 bracket has a rectangular hole for a anti rattle piece of rubber for the stone guard.

C9WY-17755-A Front bumper mounting bracket, 1969-70 Mercury Cougar driver side.

C9WY-17A750-A Sold individually, two required per car. Right is the same as left. These Western rear bumper brackets are not heavily rusted, the threads are in perfect shape and they are not bent.

Replaces Ford part #C9WY-16B554/5. Good quality part made with correct type of rubber. Sold as pair only.

This optional used front bumper guard was unique to the 1969-70 Mercury Cougar. These are sold individually and the passenger side (right hand) is the same as the driver side (left hand). The chrome plating was pretty low quality back n the day and these will have some scratches and pitting as they are and almost 50 year old original part. These are rather rare so we put a high value on our cores. Ford part # C9WY-17996-A. Check out this video ...