Trunk

Threaded anchor that slides into the trunk hinge on each side. Sold individually, two needed per car. These are for Cougar and Mustang built before approximately 3/31/1971. Look for bolt spacing of 3 inches on those trunk lids.  Ford number 6242752. *Note - Trunks after March 31, 1971, used a different anchor plate. Bolt spacing of about 3 inches.

Threaded anchor that slides into the trunk hinge on each side. Sold individually, two needed per car. These are for Cougar and Mustang built after approximately 3/31/1971. Look for bolt spacing of 4-1/4 inches on those trunk lids.  Ford number C9AZ-6242752-A. *Note - Trunks prior to March 31, 1971, did not use this anchor plate. I think that they had a bolt spacing of 4-1/2 inches.

These keep the trunk hinge spring rods from rattling. These are a reproduction of the anti-rattler for 67-68 Cougar / 65-68 Mustang.   Replaces Ford part # C5ZZ-6545028. These also work for the 69-70 Cougar / Mustang better than what came factory, which, according to the Ford MPC, for 69-70 would have actually been 1/8" x 7/8" Vinyl Foam Weatherstrip Tape, Ford part C6AZ-19627-A. Check out our trunk torsion bar installation video: ...

These barrel nuts or clips are exactly like the original ones inserted into the trunk for attaching 1967-68 "Mercury" script, and 1971-72 Mercury Cougar "Mercury" Hood scripts. The manufacturer indicates that these tubular nuts fit 1/8" holes. Pin size on those emblems are 3/32". These clips are also used to attach the 1967 quarter panel emblems. The install is basically the same as shown here: https://youtu.be/mcd788WUNns ...

Reproduction bolts for the deck/trunk lid latch for the Mercury Cougar or Ford Mustang. This is a set of five bolts and will fit both the standard and XR7. Total of 5 bolts used 1969-73, 1967-68 Cougars will only use 2. We think that Mustangs use 5 on all years 1967-73. AMK F-227 Check out this video

Bracket tack welded in the trunk to reinforce the rear structure for mounting the rear bumper. Ford part number C7ZZ-17B862-A, fits all 1967-68 Mercury Cougar and Ford Mustang. These are sold individually, these are not side specific. There is also a reproduction version available. Used part cut from a 1967-68 Mercury Cougar, some spot welds will need to be drilled out on your end. Picture shows approximately what you will receive. 

Used trunk plate or bracket for mounting the "J" bolt for the spare tire. Several versions of this bracket, this is the most common one. Mounts flat to the trunk floor surface on all 1967-70 Mercury Cougar hard tops, with full sized spare tires. Additionally, 1971-73 Mercury Cougar convertibles. We cut these out of the trunk floors, so there will be some metal preparation for the customer. Ford part number C7AZ-6247076-A.

Used trunk plate or bracket for mounting the "J" bolt for the spare tire. Several versions of this bracket. Mounts on a corner of the trunk floor surface. 1969-70 Mercury Cougar convertibles, with full sized spare tires. Additionally, 1971-73 Mercury Cougar hard tops. This folded bracket was also used with cars with space saver spare tires, or trunk mounted batteries. We cut these out of the trunk floors, so there will be some metal preparation for the customer. Ford part...

Weld in bracket for attaching the trunk lock striker on any 1967-68 Mercury Cougar. Majority of these have rust forming at the base where it meets the trunk floor. Removed from a rust free western Cougar. Ford part number C7WY-6543235-A.

Weld in bracket for attaching the trunk lock striker on any 1969-70 Mercury Cougar. Majority of these have rust forming at the base where it meets the trunk floor. Removed from a rust free western Cougar. Ford part number C9WY-6543235-A.

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Ford part number C7ZZ-17B862-A, fits all 1967-68 Mercury Cougar and Ford Mustang.Sold as a pair and are not side specific. 

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Fits all 1969-70 Mercury Cougar and Ford Mustang. Sold as a pair and are not side specific. 

Used clip to attach the rear deck / trunk lid moulding / trim on the Mercury Cougar that comes with a reproduction cadmium plated acorn nut. Seven of these clips were used to mount the anodized aluminum 1967-68 trunk lip moulding / trim to the trunk. These clip can also be found on some early 1969 Cougars with a stainless steel deck moulding / trim. This used clip is for our type "A" personality purists that insist on having the original part, even though nobody will ever see it. If ultimate...

Used clip for the stainless steel rear deck / trunk lid moulding / trim for the Mercury Cougar. This clip will also work on the 1967-68 aluminum rear deck / trunk lid moulding / trim. Seven of these units are required per moulding / trim and the acorn nut will have some rust on it. If originality is not a issue, you can get our reproduction clip here and save a little of that hard earned income. For more insight on this tricky trunk trim, check out our video below: ...

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

This decal was used on the Standard model Mercury Cougar for 1968 and both the XR7 and Standard model Mercury Cougar for 1967. Will require slight trimming for perfect fit. If you place a piece of 80 grit sand paper (or file/emery board) on a firm surface you will be able to bring the height of the decal down with just a few strokes of both the upper and lower edge. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive...

Located on the bottom side of trunk lid.

Very correct looking reproduction used only on the 1968 XR7 Mercury Cougar. This decal may need slight trimming to fit perfectly into the recessed portion of your lock cover. Check out this video

New rear seat to trunk steel divider for your Mercury Cougar. We had this one made specifically for the Mercury Cougar and it is designed to replace the flimsy tar based cardboard factory divider.We have noticed that after 40 plus years of chassis flex, the welds on the cross braces behind the rear seat tend to be broken. When installed properly behind the rear seat, this 18 gauge steel divider will provide stiffness to the chassis. This divider can be bonded, screwed or welded into your car...

NOTE: You  can save on shipping costs by ordering our template (traced out on butcher paper) and cut your own. New rear seat to trunk steel divider for your Mercury Cougar. We had this one made specifically for the Mercury Cougar and it is designed to replace the flimsy tar based cardboard factory divider.We have noticed that after 40 plus years of chassis flex, the welds on the cross braces behind the rear seat tend to be broken at the top or bottom. When installed properly...

This listing is for a template of the rear seat to trunk steel divider for your Mercury Cougar. Beneficial for international customers who would like to save on shipping costs, or anyone who can use this template to cut their own from the sheet metal of their choosing. Traced out on butcher paper.We have noticed that after 40 plus years of chassis flex, the welds on the cross braces behind the rear seat tend to be broken at the top or bottom. When installed properly behind the rear...

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very...

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

High quality reproduction adhesive emblem for your deck lid. Measures 6.5" wide by 2.35" tall. It has the correct black paint applied to the sides. If you have a 71-73 Cougar this chrome emblem is a much better match to your other emblems even though it is not technically correct. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think...

Adhesive backed, located on the right side of your deck lid.  We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often, as you can see one of our example photos above, the line workers did not even attempt to get them very well centered. Both emblems were placed on the RH side of the deck lid "somewhat" centered top to...

Reproduction Fastener Kit - Deck / Trunk Lid & Hinges for the 1968 Mercury Cougar / 1968 Ford Mustang 

This kit mounts the wing to the pedestal.

These dense, cardboard fillers are placed over the trunk drop offs. They are sturdy reproductions that fit well and every old Cougar seems to need them as moisture and general wear and tear take their toll over the decades. Sold as a pair only. If you see these advertised for less money elsewhere we would like to be notified.

These die cut sturdy trunk filler boards fit over either side of the trunk drop off and allow your trunk mat to lay flat over the trunk drop off areas. Sold as a pair.

Sold as a pair. Not only are these usually in poor shape but more times than not they are missing altogether. Great price on a quality, die cut part.

Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.

This gasket is found behind the trunk lock housing, which the lock itself sits in behind the trunk lock cover plate, and forms a seal between the trunk lock housing and the trunk itself. Made of soft rubber much like the original. Replaces Ford part #: C7WY-6543625. Check out this video

Replaces Ford part #C9ZZ-6344228, sold as a pair. This is our economy version.

These are Concours quality with correct bevel and markings.. Sold as a pair.

This is the 1.37" X 1.66 X .31 plastic grommet that goes inside the trunk to protect the trunk wires from rubbing the edges of the sheet metal body. This grommet was also used for the hood light wiring under the hood.

Used grommet for protecting the trunk light wiring as found on 1967-70 Mercury Cougar and Ford Mustangs. Ford part number C4AB-14603-A.

Good used driver side trunk or deck lid hinge. Fits all 1967-70 Mercury Cougar and Cougar convertible models. We also sell the passenger side hinge individually, or buy a right and left pair here. Ford part number C7WY-6542701.WCCC also sells torsion bars and the tool to remove and install trunk torsion bars. ...

Good used cut off driver side, trunk or deck lid hinge. Fits all 1971-72 Mercury Cougar and Cougar convertible models. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 3 inch spacing. These are welded to the body, expect some cleanup to the metal prior to welding. We do not drill spot welds.Additionally fits 1971-73 Mustang hardtop and convertible models (body style 65 and 76). Ford part number D1ZZ-6542700 and...

Good used driver side trunk or deck lid hinge. Fits all 1972-73 Mercury Cougar and Cougar convertible models. Additionally fits 1972-73 Mustang hardtop and convertible models (body style 65 and 76). We also sell the driver side hinge individually. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 4-1/4 inch spacing. These are welded to the body, expect some cleanup to the metal prior to welding. We do not drill spot...

Good used pair of trunk or deck lid hinge. Fits all 1967-70 Mercury Cougar and Cougar convertible models. We also sell the hinges individually. Ford part number C7WY-6542700 and C7WY-6542701.WCCC also sells torsion bars and the tool to remove and install trunk torsion bars.

Good used passenger side trunk or deck lid hinge. Fits all 1967-70 Mercury Cougar and Cougar convertible models. We also sell the driver side hinge individually, or buy a right and left pair here. Ford part number C7WY-6542700.WCCC also sells torsion bars and the tool to remove and install trunk torsion bars. ...

Good used cut off passenger side, trunk or deck lid hinge. Fits all 1971-72 Mercury Cougar and Cougar convertible models. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 3 inch spacing. These are welded to the body, expect some cleanup to the metal prior to welding. We do not drill spot welds. Note that there are an early and late style of these hinges. Early style has a bolt spacing of 3 inches for installing the...

Good used passenger side trunk or deck lid hinge. Fits all 1972-73 Mercury Cougar and Cougar convertible models. Additionally fits 1972-73 Mustang hardtop and convertible models (body style 65 and 76). We also sell the driver side hinge individually. Ford part number D1ZZ-6542700. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 4-1/4 inch spacing. These are welded to the body, expect some cleanup to the metal prior to...

Fits Standard and XR7 Sold as a Set as Pictured.

Reproduction pair of trunk or deck lid hinges. Fits all 1967-70 Mercury Cougar and Cougar convertible models. We also sell the reproduction trunk torsion bars. Replaces Ford part numbers C7WY-6542700 and C7WY-6542701.