Trunk Lock / Latch Parts

Reproduction bolts for the deck/trunk lid latch for the Mercury Cougar or Ford Mustang. This is a set of five bolts and will fit both the standard and XR7. Total of 5 bolts used 1969-73, 1967-68 Cougars will only use 2. We think that Mustangs use 5 on all years 1967-73. AMK F-227 Check out this video

Weld in bracket for attaching the trunk lock striker on any 1967-68 Mercury Cougar. Majority of these have rust forming at the base where it meets the trunk floor. Removed from a rust free western Cougar. Ford part number C7WY-6543235-A.

Weld in bracket for attaching the trunk lock striker on any 1969-70 Mercury Cougar. Majority of these have rust forming at the base where it meets the trunk floor. Removed from a rust free western Cougar. Ford part number C9WY-6543235-A.

This decal was used on the Standard model Mercury Cougar for 1968 and both the XR7 and Standard model Mercury Cougar for 1967. Will require slight trimming for perfect fit. If you place a piece of 80 grit sand paper (or file/emery board) on a firm surface you will be able to bring the height of the decal down with just a few strokes of both the upper and lower edge. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive...

Very correct looking reproduction used only on the 1968 XR7 Mercury Cougar. This decal may need slight trimming to fit perfectly into the recessed portion of your lock cover. Check out this video

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. Ford part number C7SZ-6543283-A. 1967 - 1968 only. Check out this video

Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.

This gasket is found behind the trunk lock housing, which the lock itself sits in behind the trunk lock cover plate, and forms a seal between the trunk lock housing and the trunk itself. Made of soft rubber much like the original. Replaces Ford part #: C7WY-6543625. Check out this video

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the ignition / door key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-A Check out this video

During installation, check for proper alignment with trunk latch. Trunk latch and striker should engage smoothly, both items are adjustable. We only save the rust free latches with no wear or rust, the rest are tossed. Fits 1967-68 Mercury Cougar. Ford part number C6OZ-6543252-A.

During installation, check for proper alignment with trunk latch. Trunk latch and striker should engage smoothly, both items are adjustable. We only save the rust free latches with no wear or rust, the rest are tossed. Fits 1969-70 Mercury Cougar and 1968-69 mid sized Ford Torino, Fairlane, etc. 1968-69 Mercury Cyclone, Montego, etc. Ford part number C5AZ-6243252-B.

During installation, check for proper alignment with trunk latch. Trunk latch and striker should engage smoothly, both items are adjustable. We only save the rust free latches with no wear or rust, the rest are tossed. Fits 1971-73 Mercury Cougar and Ford Mustang. Ford part number D1AZ-6543252-A.

Replaces Ford Part # C7AZ-6243505-B Click on images to enlarge.

Keyed alike as the originals were, includes two keys, trunk cylinder gasket and retaining clip. Ready to go kit for your 1969 - 1970 Cougar.

Originals keyed alike with Ford key. code on glove box lock matches the trunk lock perfectly. Includes 2 Ford keys, trunk cylinder gasket and retaining clip. Ready to go kit for your 1969 - 1970 Cougar. will fit 1971-73 Cougars, but trunk clip may be different. These used originals are much better than the reproduction lock sets.OEM FoMoCo parts.

Reproduction trunk lock cylinder with keys for the 67 - 68 Mercury Cougar. Replaces Ford Part # C7SZ-6543505-A or C7SZ-6543507-B (Glove box/Trunk lock kit). Below are some basics about removing and replacing your lock cylinder and lock cover. When removing the cylinder from the lock housing this button must be depressed to allow the cylinder to slide out the front of the housing.  The only way to depress the button is to have the key in the cylinder and partially turned as if to...

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. C9WY-6543283-A.1969 and 1970 Cougar only.

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. 1971 - 1973 Cougar only.

A perfectly working, matched set of trunk and glove box locks with key is getting rather hard to come by these days. These two matching locks are guaranteed to work perfectly. Includes 1968 style glove box lock, 1967-68 Cougar trunk lock cylinder with one "Ford" cut key to the coded to the number imprinted on the glove box lock. This is a matching set with new key. 1967 glove box locks has square edges on the front of the lock. Starting in 1968 the lock had a rounded edge on the front. We also...

New Old Stock, NOS, original keyed alike with Ford key. code on glove box lock matches the trunk lock perfectly. Includes 2 Ford keys, trunk cylinder gasket, glove box stainless bezel, and screws. Fits all 1971-73 Mercury Cougar.  OEM Ford part number D1AZ-6543507-A.

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.

Correct style nut with captured washer for attaching hood scoops, 1969-70 Mercury Cougar inside door handles, and 1967-68 trunk lock. Correct nuts would have been black phosphate, these are shiny gold as shown.

Rubber pad for installing the trunk lock mechanism to deck lid. Check out this video

This deck lock housing has been carefully stripped, polished and triple plated. You can send yours in in advance as an exchange or pay the core charge and return your old one later. Do know once a multi-faceted part like this has been stripped, polished and replated, some of the crisp, sharp detail will be muted and it will never again look just like factory. If you have extra cores we are buyers, especially if your lock assembly is complete. Check out this video ...

These spacers are required to properly mount the trunk lock housing to the trunk. Two required per car, sold individually. Ford part number C7WY-6543565-A. Check out this video

These spacers are required to properly mount the trunk lock housing to the trunk lid.  Sold as a pair. Replaces Ford part number C7WY-6543565-A. Follow this link to find the lock housing nuts. Check out this video

New O-ring gasket for the 1967-68 Mercury Cougar flip trunk lock cylinder. Lock cylinder must be removed from the trunk lock housing to install. Original O-rings are normally cracked and broken when we disassemble them. 

Fits Standard and XR7 Sold in Set of 4.

Used trunk or luggage compartment latch, fits all 1967-73 Mercury Cougar and many other Ford and Mercury cars. Comes with 3 bolts for mounting.Replaces Ford part number C5AZ-6243200-A.

High quality chrome finish on lever & base. Improved cable for smooth operation. You must have correct trunk latch to use this remote. Detailed instructions included. Look for the trunk latch in our 'related items' tab.

This is an upgrade to the Electronic Trunk Release. Allows trunk to be opened with just the push of a button on two wireless remotes that are included. NOTE: This item requires that you have a latch mechanism equipped with the remote release tab.

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

This spring has two functions. The first is to connect the rod that opens the latch to the deck lock cylinder. The second is to put tension on the cylinder so as to return the key to its perpendicular resting place after unlocking the deck lid. Check out this video

Used cover with dull chrome. This used to be a very sought after and expensive part due to how difficult they were to find. Now that our show quality reproductions are here they have little value... Great for someone that just wants their driver to look complete. Fits all 1967-68 Mercury Cougars, Standard and XR7 models. Decal inserts available separately. Check out this video

For 1967 both the XR7 and Standard model used the decal shown on this reproduction trunk lock cover. For 1968 only the Standard model used this decal as the XR7 and XR7G had their own unique center badging. *NOTE* You will have to apply the licensed by Ford decal to the deck lock cover. Check out this video

This is for the person who already has a decal or XR7G emblem to place in the center section. Maybe you have a custom idea? Same great quality and flawless fit as our other deck lock covers. *NOTE* After a long hiatus these are finally back in stock! They were worth the wait, the quality is really good on this new reproduction. Check out this video

Beautiful reproduction truck lock cover with new XR-7 decal. Very true to original, the only noticeable difference being that the corners of the decal are slightly more trimmed than the originals. Check out this video

Save your hard earned money when you buy our reproduction deck lock cover with the new XR7-G emblem already installed! Check out this video

Weld in bracket for attaching the trunk lock striker on any 1971-73 Mercury Cougar, coupe or convertible. Majority of these have rust forming at the base where it meets the trunk floor. Removed from a rust free western Cougar. Ford part number D1WY-6543235-A.

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. Ford part number C7SZ-6543283-A. 1967 - 1968 only. Check out this video

This is the factory Ford remote trunk latch as used on luxury cars such as Thunderbird or Lincoln. As you can see from the photo, they are made (and install) exactly like our Cougar trunk latches, but with the addition of a release tab. These can be installed to use either a cable, vacuum, or solenoid release.

This is for the person who is missing it all. Includes all you need as seen in the picture and includes the reproduction chrome cover on a good used housing. Let us know in the comments whether you prefer a Standard or XR7 decal installed on the flip up door. Check out our video below showing how to easily remove and re-install your 67-68 trunk latch, lock, and cover plate and some info on getting a new key made. This icon means that we're looking to buy this part!WCCC is a buyer of used and...

Good used cylinder as taken from a 1967 - 1968 trunk lock housing. Will have minor damage but cosmetic only, 100% functional. Ford Part # C7SZ-6543505-A or C7SZ-6543507-B (Glove box/Trunk lock kit) Check out this video Below are some basics about removing and replacing your lock cylinder and lock cover. When removing the cylinder from the lock housing this button must be depressed to allow the cylinder to slide out the front of the housing.  The only way to depress the button is to...

A perfectly working, matched set of trunk and glove box locks with key is getting rather hard to come by these days. These two matching locks are guaranteed to work perfectly. Includes 1967 style glove box lock, 1967-68 Cougar trunk lock cylinder with one "Ford" cut key to the coded to the number imprinted on the glove box lock. This is a matching set with new key. 1967 glove box locks has square edges on the front of the lock. Starting in 1968 the lock had a rounded edge on the front. We also...

This matched set is actually for a 1968 model Cougar but works just as well on a 67. The only difference being 1967 had squared off edges on the glove box button and 1968 had rounded edges which are safer in a collision.Ford Part # C7SZ-6543505-A/C6OZ-6206281-C or C7SZ-6543507-B (Glove box/Trunk lock kit)