Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Pair (2) Bolts for securing the inspection cover for any C-4 automatic transmission 1967-68 Mercury Cougar or 1965-70 Ford Mustang. Additionally also fits FMX transmissions 1969-73 Mercury Cougar.or Ford Mustang.
Replacement tail shaft bushing, for all 1964-73 C4 transmissions.
Replacement tail shaft bushing, for all 1969-73 FMX and 1967-73 C6 transmissions.
Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...
These reproduction brake and clutch pedal bushings are made from high strength plastic that is wear resistant. Two are required for automatic cars, four for manual transmission cars. Sold as a pair. Replaces Ford part # B7AZ-2471-A.
Reproduction pair of brass 3/8 ID bushings for the clutch rod. Protects clutch equalizer and rod, and removes excess play.We also sell these in nylon. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it...
(7526) Nylon plastic injected. Correct original design. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these.Replaces Ford Part #: C0AZ-7526-B.Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they...
Internal tail shaft assembly from a C-6 transmission. We only disassemble up to what you see in the picture.
Sold individually Zinc (dark silver)
Replaces Ford part # 351089-S Zinc (dark silver) finish Sold individually
Bare cast aluminum C4 transmission case from a 1967-68 Mercury Cougar or Ford Mustang. Inspected for damage. Replaces Ford part number C6DP-7006-A.
This bezel was never offered from the factory on a Cougar but is a very attractive part for those with a manual transmission and no console. Works with rubber or leather shift boot, three or four speed manual transmission. Check out our video on rebuilding your shifter below: ...
Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.
This A/C tag clip fastens the aluminum tag to top of the A/C pump.
Reproduction Lower Radiator Core Support Loom Clip for the 1967 - 1968 Mercury Cougar / 1967 - 1968 Ford Mustang
This is the speedometer cable clip that connects to the firewall and transmission tunnel. Replaces Ford Part # : 373829
Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.
(7521) The attaches to the bottom leg of your equalizer bar and the pointed end fits into the recess of your clutch fork. Replaces Ford Part #: C7ZZ-7521-L.
Equalizer bar or "Z" bar for small block engines with a manual transmission. Both 3 and 4 speed manual transmissions. Replaces Ford part number C7ZZ-7528-G.
Nice reproduction of the original. Street name is Z-Bar. For all 1967 - 1970 FE engines 390 and 428CJ. Replaces Ford part #: C7ZZ-7528-B.
Clutch equalizer pivot mount, engine side. Zinc plated. Replaces Ford part #: C7ZZ-7A572-BR.
Mounts on frame for equalizer bar to ride on. Replaces Ford Part #: C5ZZ-7507-A.
Replaces Ford Part # : C7ZZ-7507-B
C5OZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 9-1/4 inches long. Specifically used with a 157 tooth flywheel, as opposed to the 164 tooth fly wheel used after Feb 1968.Replaces ford Part # C5OZ-7515-B. Cougar before 2-15-1968, 289/302 Engines. Mustang before 2-15-1968, 289/302 Engines. *Note - This style of clutch fork uses the 'wire' for the holder, not the clip. ...
C5OZ-7515-B Manual transmission clutch fork for small block V8 engines - 3 and 4 speed, stick shift transmissions. Fork measures 9-1/4 inches long from the divot where the rod rides to the tip of the forked end. Specifically for the C5DA-6394-A bellhousing that used a 157 tooth flywheel. Cougar 1967 through 2-15-1968. XR7, XR7-G. Mustang 1965 through 2-15-1968. 2+2, GT. Fairlane 1965 through 2-15-1968. 500, XL, Custom. Torino / Ranchero 1968 through 2-15-1968. 500, XL Comet 1965 through...
Used until early (prior to 2/15/1968) on manual transmission cars. Comes with rivets. Replaces Ford part #: B9AZ-7522-B.This style uses the early clutch fork with the anti rattle wire.
Manual transmission clutch kit for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is a 10 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.
Manual transmission clutch kit for all 1967-69 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 390 engines. This is a 11 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.
C7ZZ-7519-A We also offer used clutch pedals along with our quality reproduction 1967-1968 clutch pedal. These pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.
Bumper that helps stop the 'clunk' noise when you take your foot off of the clutch pedal on manual transmission 67 - 68 Cougars and Mustangs.Replaces Ford Part Number: C7ZZ-7583
This kit has everything you need to repair your clutch and brake pedal and pedal support in one easy kit. Repairs 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Plus many other Ford cars.This kit requires welding. For use on pedal hangers that are all wallered out, or 1971-73 pedal hangers that are not round. Kit has roller bearings. Quality Scott Drake / Holley product. *Hint - All 1967-70 brake pedal hangers have the clutch pedal shaft bushings, even the automatic cars. The originals are...
This reproduction stainless trim mounts over your pedal pad. Not only adds style but also holds your pad in place. Replaces Ford part number C5ZZ-7B544-A.
Includes machined pedal shaft, washer and special pin. Replaces Ford Part #: C5ZZ-2478-AK.
(7521) Correct contour insures a good fit, 12 1/2" long. This is for both 3 and 4 speed cars. Check out the comparison picture with the off-shore crapola rod sold by most vendors. The only reason you replace this rod is that it is wore down in the area where the bushing seats. Unfortunately when the Chinese were given a sample to copy they must have been given a worn out one! The one on the left (made in USA) fits tight with the bushing and was copied from a NOS sample. Replaces Ford Part #:...
Manual transmission clutch throw out bearing for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is with a 10 inch disc.
Reproduction aluminum shift indicator console overlay for the Mercury Cougar or Ford Mustang. Although a brushed finish is correct, this reproduction has a coarser brush stroke when compared to the originals and is a bit dull. We recommend a quick polish to make them look closer to the finish of the originals. These fit well, and unless you put them up against an original, it is hard to tell the finish is slightly different. This installs around your console...
Reproduction transmission cooling lines for the Mercury Cougar or Ford Mustang equipped with the C-4 automatic transmission. These lines are sold in pairs.
Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang produced from 1967 through early 1968 that came equipped with the C-6 automatic transmission and 390 engine. These lines are also available in stainless steel and are sold in pairs.
Sold individually Zinc Dichromate (yellow-rainbow)
First generation Cougars 1967 and 1968, used a single bracket for C4 automatics and both 3 speed and 4 speed manual transmissions. This bracket also carried over to 1969 and 1970 with 351 or Boss 302 engines and either 3 or 4 speed manual transmissions. Ford part number C7ZZ-6A023-D. This part weighs 2.28 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 1/4" on center and the passenger side 2 3/4" on center.The reproduction Dynacorn part...
New crossmember to adapt the Tremec TKO manual transmission to the Mercury Cougar or Ford Mustang. This unit can also be used for the Ford AOD.
Grade A used deluxe shifter handle in black. Nice used condition, minor cracks in the plastic on the bottom. No release button or set screw included. Fits 1967 Mercury Cougar XR7 and 1967 Ford Mustang with IDG or Interior Decor Group and all Shelby Mustangs with automatic. This one year only, T handle, has concave or recessed buttons. Ford part number C7ZZ-7213-A. We know that Scott Drake is using this number for 4 speed manual knobs, which was a made up Ford part...
Grade B used deluxe shifter handle in black. Fair used condition, cracks in the plastic. No release button or set screw included. Fits 1967 Mercury Cougar XR7 and 1967 Ford Mustang with IDG or Interior Decor Group and all Shelby Mustangs with automatic. This one year only, T handle, has concave or recessed buttons. Ford part number C7ZZ-7213-A. We know that Scott Drake is using this number for 4 speed manual knobs, which was a made up Ford part number on their part. We...
New old stock deluxe shifter handle in black. Perfect condition, no cracks in the plastic. No release button or set screw included. NOS Fits 1967 Mercury Cougar XR7 and 1967 Ford Mustang with IDG or Interior Decor Group and all Shelby Mustangs with automatic. This one year only, T handle, has concave or recessed buttons. Ford part number C7ZZ-7213-A. We know that Scott Drake is using this number for 4 speed manual knobs, which was a made up Ford part number on their part. We...
Original dipstick or in Ford speak "Indicator - Oil Level" for C4 automatic transmissions. Application for 1967-68 Mercury Cougar 1966-70 Ford Mustang with 289/302 engines and C4 automatic transmissions, code "W" on your door data plate.Ford part # C6OZ-7A020-B.
Reproduction transmission dipstick tube for 67 - 70 Cougars or Mustangs equipped with the C4 automatic transmission.Replaces Ford Part number C6AZ-7A020-B
Fits C4 transmissions. Painted glossy black. O-ring included Replaces Ford part # C6OZ-7A228-B. Application 1967 - 1968 Mercury Cougars with 289/302 engines and automatic (C4) transmissions, code "W" on your door data plate. 1966 - 1968 Ford Mustangs with 28/302 engines and automatic transmissions, code "W" on your door data plate.
Fits C4 transmissions. Chrome finish. O-ring included Replaces Ford part # C6OZ-7A228-B. Application 1967 - 1968 Mercury Cougars with 289/302 engines and automatic (C4) transmissions, code "W" on your door data plate. 1966 - 1968 Ford Mustangs with 28/302 engines and automatic transmissions, code "W" on your door data plate.