Exterior Trim

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

These are 100% correct reproductions for the 1968 Mercury Cougar XR7-G, but will fit any 1967-68 Cougar. These will NOT lay flat against the valance, as the originals did not. These are beveled on purpose and if you attempt to straighten them they WILL break. The reproductions that do lay flat against the valance are no longer being produced. We cannot warranty these against any attempts to straighten them. Sold as a pair. ...

A scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot that did not come out 100%, a slip on the buffer wheel or a pin hole created by over polishing are what you can expect on a blemished piece of trim. We try to carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to... From 10-15 feet away these will look good...

A scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot that did not come out 100%, a slip on the buffer wheel or a pin hole created by over polishing are what you can expect on a blemished piece of trim. We try to carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to... From 10-15 feet away these will look good...

Used 1968 Mercury Cougar GT-E horizontal grille bar clip or keeper for the center grille section. This is a rare find, limited to stock on hand.

This trim clip is a little larger than the original C4GB-6242364-A retainer assembly Ford used and looks a little different, but will work just fine for the front extension mouldings. This will also suffice as a good substitute for the 46 clips used on the 1968 GTE side moldings. Sold Individually.Length: 13/16" from lip to lip.

This fragile little clip attaches to the bottom outer edge of the front fender extension and holds the tail of the aluminum eyebrow moulding to the extension, one per side. They almost always fail when you remove them, and to be honest, we rarely have them in stock. We do not list these hard to find parts to tease you, but rather for documentation purposes. We do offer a nice reproduction clip that you can get right here that will work great. ...

Reproduction large moulding / trim clip for the rear quarter extensions and front fender extensions on the Mercury Cougar. The molding / trim on the 1967-68 rear quarter extension and 1969 front fender extension both require 2 different sizes of clips to properly hold them in place. For the 1967 and 1968 rear quarter extensions, you will need one of these large clips and 1 smaller clip per side. For the 1969 Cougar you will need 1 of these larger clips along with 2 smaller clips per side. This...

Reproduction clip for the rear quarter extension moulding / trim on the Mercury Cougar. The rear quarter extension moulding / trim uses 2 different size clips. This is the smaller of the two. One per side, 2 per car. Get the larger clip here. Replaces Ford part # C7WB-65291B80-A. *NOTE* Will work with the 1967-70 trunk trim, but the nuts are wrong style.

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

Used rocker moulding end clip. Fits all 1968 Mercury Cougars. This clip is plastic and metal, it has a stud which goes through the body of the car. sold individually, 4 total needed per car. Our all metal version of this clip is reproduced and is a better value. Find it here.Ford part number C7OZ-6221094-A.

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

Used driver side (left hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

Used passenger side (right hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

Stainless steel clip on guards for the rear edge of the 1967 and 1968 Cougar doors. Would have been part of the exterior deccor option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. These used trim parts will have many very small dings and scratches. The driver side moulding will have substantially more damage than the passenger side moulding. Ford part number C7WY-6220910-A. NOTE: This item will not ship until useable cores are received. ...

C7ZZ-652220-B Restored, stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Passenger side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind. *Note - Excludes Mustang fastback and convertible.

If you do not have a core that is worthy of restoration we have them for sale.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. For more info on aluminum trim restoration & core exchanging, check out our video below. ...

The 1967 XR7 did not have rocker panel mouldings as did the 1968 - 1973 XR7 Cougars. All 1967 XR7 models came equipped with these "Hash" marks fastened to the rear of both rockers, at a rear tilting angle. Both sides received seven ribs, held by two Phillips screws each for a total of fourteen ribs in all. They were painted semi-gloss black in the recessed areas and the screws themselves were black as well. The leading ribs are usually pretty rough looking due to road debris wear, the one...

Flat nut for attaching the "Mercury" script on the front fender extension on all 1967-68 Mercury Cougars. 4 total needed for emblem installation on that fender extension. Also attaches the reproduction running cat emblem to the headlight door on 1967-69 Mercury Cougars.

This reproduction tape is a must for anyone replacing their stainless steel window trim pieces on the 1967 - 1968 Cougar or Mustang. Can be used on any of the side windows. We suggest saving the original quarter window rubber surround if possible, due to the curves, but this tape can be used there as well if needed. This glass setting tape is designed to look and perform similarly to the original Ford factory material. It creates a water tight bond as well as...

NOS part that shows shelf wear and may need to be repainted in places. For 1967 and early 1968 Cougars built prior 12/15/1967. Can easily be made to fit 1968. Ford part numbers: C7WY-13A137-B (Headlamp exterior cover)C7WY-13A155-A (Headlamp hinge) Check out this video ...

Used 1968 Mercury Cougar GT-E horizontal grille bar, from the driver side headlight door. Measures 15-3/16 inches long. This is the longest section of extruded aluminum from an original car. There are a total of 7 pieces for a complete grille on a GT-E. It can be cut down to fit any other position that you may be missing. This is a rare find. This one has road tested, meaning that it does have some minor scuffs from use.

These are very correct looking reproductions and sold as a complete set. They do not come with the keepers that go on the backside of the grill, so you will be using common flat washers which actually work just fine. Check out this video ...

Complete set of seven, extruded aluminum original horizontal GTE grille bar set. Includes all parts in good condition including the four rectangular, notched brackets that attach the center bars from the back side. Check out this video ...

This listing is for all six pieces restored and of course requires you send your cores in advance. It can take anywhere from 1 to 4 months depending on what time of year it is and where we are in our cycle with our plater as we send a minimum of $20k in at a time. We make sure they are separated from the more common parts we have and these are treated with special care every step of the way. On this particular set we never ask them to hurry. Do know that if you have extra holes drilled they...

This complete set of grille bars have been chemically dipped to remove the chrome and are ready to be painted black for your 1967 - 1968 Resto-Mod or 1968 GTE. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved before these are paint ready. We hand select premium parts that have minimal defects.If you send cores in for exchange they must be pit free and no scrapes so as to qualify for...

This pair of tail light bezels have been chemically dipped to remove the chrome and are ready to be painted black for your 1967 - 1968 Resto-Mod or 1968 GTE. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved before these are paint ready. We hand select premium parts that have minimal defects.  If you send cores in for exchange they must be pit free and no scrapes so as to...

Restored passenger side (right hand) center grill moulding / trim for the Mercury Cougar. As you can tell, price wise, you are much better off to purchase the entire set together as opposed to one at a time.Ford part # C7WY-8A158-A. *NOTE* This unit carries a $20 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim...

Used passenger side (right hand) center grill moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches, or corrosion. Perfect for your daily driver that is in above average condition. Ford part # C7WY-8A158-A. *NOTE* This unit carries a $20 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for...

1968 Mercury Cougar left side or driver door moulding found on the GT-E models. This unique trim split the lower silver color from the body color. Arrow straight, dull, a couple of minor, very small scratches. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. We will take used GT-E trim in trade towards the reproduction GT-E trim call 503-463-1130 for details.Ford part # C8WY-6520939-A.Due to the difficulty...

1968 Mercury Cougar right side or passenger door moulding found on the GT-E models. This unique trim split the lower silver color from the body color. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. The trim pictured is dull, but has no dents or scrapes. Laser straight with only minor scratches and pock marks from road debris on the lower side closest to the fender. We will take used GT-E trim in trade...

This restored drip rail moulding / trim will have had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. Our mouldings / trim are sold outright, as a pair, or one side only. Most people will be satisfied with our used grade "A" drip rail mouldings / trim, however these are for the person that is striving for perfection with his or her show car. Ford part # driver side...

Core driver side (left hand) fender extension moulding / trim for the Mercury Cougar. This is a great option for those of you who like to save money by restoring your own parts.Ford part # C7WY-16075-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

Used driver side (left hand) fender extension moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches or corrosion. Perfect for your daily driver that is in above average condition. Check out all our restored and used mouldings in the "exterior trim" section. Normal 0 false false false EN-US X-NONE X-NONE Ford part # C7WY-16075-A. *NOTE* This unit carries a $30 refundable core charge. If you are unable to return your core within 30 days after...

Core passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. Good used core with minor dings, scratches, and dullness.Ford part # C7WY-16076-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

NOS passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear. Also, the tooling was often near the end of its life, so do not be alarmed when you find the fit and finish is not as good as our restored trim.Ford part # C7WY-16074-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

Restored passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. This is like fine jewelry for your beloved Cat!Ford part # C7WY-16076-A. *NOTE* This unit carries a $30 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section. Keep in mind we buy most trim and mouldings found on a...

Used passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches, or corrosion. Perfect for your daily driver that is in above average condition. Ford part # C7WY-16076-A. *NOTE* This unit carries a $30 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option...

1968 Mercury Cougar right or passenger side fender moulding found on the GT-E models. This unique trim splits the lower silver color from the body color. The unit shown is the one you will receive. Near mint, excellent original bright dip finish, an out of package (we still have remnants of the crispy brown FoMoCo wrapper) NOS part with minimal shelf wear. Best you will ever find, ready to put on the car as is. We won't always have this stick of trim in stock, but we will work to accurately...

1968 Mercury Cougar right or passenger side fender moulding found on the GT-E models. This unique trim split the lower silver color from the body color. This core piece good is for restoration. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. We will take used GT-E trim in trade towards the reproduction GT-E trim call 503-463-1130 for details.Ford part # C8WY-6516039-A.Due to the difficulty in obtaining trim...

Core driver side (left hand) center grill moulding / trim for the Mercury Cougar. Good used core that will have minor dings, dullness, and scratches. Ford part # C7WY-8A157-A. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. Check out this video ...

NOS driver side (left hand) center grill moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear. The tooling was also typically near the end of its life, so do not be alarmed when you find the fit and finish is not as good as our restored trim. Ford part # C7WY-8A157-A. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. Check out this video ...

Restored driver side (left hand) center grill moulding / trim for the Mercury Cougar. No core needed for this purchase. Looks better than NOS! Ford part # C7WY-8A157-A. *NOTE* This unit carries a $20 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section. Keep in mind we buy most trim and mouldings found on a...

Used driver side (left hand) center grill moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches or corrosion. Perfect for your daily driver that is in above average condition. Ford part # C7WY-8A157-A. *NOTE* This unit carries a $20 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you...

Core passenger side (right hand) center grill moulding / trim for the Mercury Cougar. Good used core with minor dings, scratches, and dullness. Ford part # C7WY-8A158-A. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. Check out this video ...