Rear Trunk / Quarter Extension Aluminum Trim

A scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot that did not come out 100%, a slip on the buffer wheel or a pin hole created by over polishing are what you can expect on a blemished piece of trim. We try to carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to... From 10-15 feet away these will look good...

Reproduction large moulding / trim clip for the rear quarter extensions and front fender extensions on the Mercury Cougar. The molding / trim on the 1967-68 rear quarter extension and 1969 front fender extension both require 2 different sizes of clips to properly hold them in place. For the 1967 and 1968 rear quarter extensions, you will need one of these large clips and 1 smaller clip per side. For the 1969 Cougar you will need 1 of these larger clips along with 2 smaller clips per side. This...

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

Core driver side (left hand) rear quarter extension moulding / trim for the Mercury Cougar. This is a good trim part that is ready for restoration or could be used on a driver.Ford part # C7WY-6529313-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

NOS driver side (left hand) rear quarter extension moulding / trim for the Mercury Cougar. This piece will show some shelf wear so don't be surprised to find that this piece is not as nice as our restored moulding / trim.Ford part # C7WY-6529313-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

Restored driver side (left hand) rear quarter extension moulding / trim for the Mercury Cougar. We have many NOS trim parts in stock, but why bother when you can get correctly restored parts for less? This part has been "bright dip" anodized just like original and will not turn a chalky white color in a few months like one that has been polished only. If you select this option (paying a core charge), we will randomly select mouldings off the shelf. Paying the core charge does not mean you will...

Used driver side (left hand) rear quarter extension moulding / trim for the Mercury Cougar. Good used driver quality moulding / trim with no obvious dings, deep scratches or corrosion. Perfect for your daily driver that is in above average condition.Ford part # C7WY-6529313-A.

Core passenger side (right hand) rear quarter extension moulding / trim for the Mercury Cougar. Good trim part that is ready for restoration or could be used on a driver.Ford part # C7WY-6529314-A.

NOS passenger side (right hand) rear quarter extension moulding / trim for the Mercury Cougar. These NOS pieces are getting difficult to source. If you have NOS parts, we will buy them!Ford part # C7WY-6529312-A.

Restored passenger side (right hand) rear quarter extension moulding / trim for the Mercury Cougar. This part has been "bright dip" anodized just like original and will not turn a chalky white color in a few months like one that has been polished only. Cores with minor dings or scratches are what is needed, smashed or folded trim parts cannot be restored. We are pretty liberal about these rear core exchanges, if you do not have a core, a similar core from a 1967-70 Cougar will usually suffice...

Used passenger side (right hand) rear quarter extension moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches or corrosion. Perfect for your daily driver that is in above average condition.Ford part # C7WY-6529314-A.

Economy reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible, except for the fact that the clips included have 8mm nuts, unlike the originals. There is however one small problem, the metal on these mouldings is much softer than the originals and you have to take extra care when installing the clips, if you apply too much pressure when installing, you will dimple the...

Restored aluminum rear deck lid moulding / trim for the Mercury Cougar. If you do not have cores that are worthy of restoration we do have them for sale. The better core you start out with, the better the end result will be! If you prefer a mirror like luster then I suggest you purchase the 1969-70 deck moulding as stainless offers a much brighter finish. Seven clips are used to install the deck lid moulding and we have new clips available here. We will accept extra cores in on exchange for...

1969 - 1970 Cougars came factory equipped with stainless trunk mouldings and 1967 - 1968 Cougars came equipped with anodized aluminum trunk lid mouldings. However if you ordered a 67-68 service replacement deck moulding from Ford anytime after 1968 you would have received a stainless steel replacement. We recently obtained 15 of these that were stored improperly where the packaging had deteriorated and the mouldings showed shelf wear. We sent them out to be polished and the results are...

This is a freshly restored 1969-70 original stainless steel deck lid moulding. It has had all minor dings and creases it may of had professionally removed and has been polished to a mirror like, better than N.O.S. finish. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the aluminum corner mouldings perfectly. Seven clips are...

This option REQUIRES sending your core in advance. This is a freshly restored 1969-70 original stainless steel deck lid moulding. It has had all minor dings and creases it may of had professionally removed and has been polished to a mirror like, better than N.O.S. finish. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the...

Used stainless steel deck or trunk moulding / trim for 1969-70 Mercury Cougar, including convertible. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the aluminum corner mouldings perfectly. This being a used, means that it will have minor scratches, and a small dent or two. Save your old mounting clips, these are sold without...

Restored three piece anodized aluminum rear moulding / trim set for the rear of the 67-68 Mercury Cougar. These pieces attach to the rear deck / trunk lid and the quarter extensions. New and used clips also available separately. Ford part #: Driver side quarter extension moulding C7WY-6529313-A, passenger side C7WY-6529314-A, deck lid moulding C7WY-6542512-A. *NOTE* Keep in mind that we do give in-store credit for extra core trim and mouldings you may have laying around (from a Cougar of...

Restored three piece anodized aluminum rear moulding / trim set for the rear of the 67-68 Mercury Cougar. These pieces attach to the rear deck / trunk lid and the quarter extensions. New and used clips also available separately. Ford part #: Driver side quarter extension moulding C7WY-6529313-A, passenger side C7WY-6529314-A, deck lid moulding C7WY-6542512-A. If you select this option (paying a core charge), we will randomly select mouldings off the shelf. Paying the core charge does not...

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 

This clip looks just like the larger quarter extension moulding / trim moulding clip, but is smaller (as our comparison picture shows). One clip per side is used to attach the tail end (smaller end) of the moulding / trim to the extension. This unit is also almost exactly the same as the rear deck / trunk lid moulding / trim clip, but this quarter extension clip has a slightly shorter stud. Rarely will the clip you get look as good as the pictured here, usually the "finger" will be missing....

This clip looks just like the smaller rear deck / trunk lid moulding clip but is larger (as our comparison picture shows). One clip per side is used to attach the tail end (larger end) of the moulding to the extension. Rarely will the clip you get look as good as the pictured here, usually the "finger" will be missing. These clips are for the purest where originality is of the utmost importance. If originality is not an issue, you can get our excellent reproduction clip right here and...

Used clip to attach the rear deck / trunk lid moulding / trim on the Mercury Cougar that comes with a reproduction cadmium plated acorn nut. Seven of these clips were used to mount the anodized aluminum 1967-68 trunk lip moulding / trim to the trunk. These clip can also be found on some early 1969 Cougars with a stainless steel deck moulding / trim. This used clip is for our type "A" personality purists that insist on having the original part, even though nobody will ever see it. If ultimate...

Set of seven used clips with reproduction stainless steel acorn nuts. These fit the best when using an original aluminum deck lid moulding on a 1967 or 68 Cougar. In 69-70 a stainless deck trim was used and the clip was all metal with no plastic coating. For more insight on this tricky trunk trim, check out our video below: ...

Core aluminum rear deck lid moulding / trim for the Mercury Cougar. Good core ready for restoration. No kinks, flattened areas of heavy pitting. Seven clips are used to install the deck lid moulding and we have new clips available here. Ford part # C7WY-6542512-A. *NOTE* Keep in mind we buy most trim and mouldings found on a Cougar. For more insight on this tricky trunk trim, check out our video below: ...

NOS aluminum deck lid moulding / trim for the Mercury Cougar. Rarely do we come across a true NOS 1967-68 aluminum deck lid moulding / trim. Starting in 1969, Ford gave you a stainless moulding as a service replacement part. Seven clips are used to install the deck lid moulding and we have new clips available here! Ford part # C7WY-6542512-A. *NOTE* Keep in mind we buy most trim and mouldings found on a Cougar. For more insight on this tricky trunk trim, check out our video below: ...

Premium reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible. This version is also much more rigid when compared to the economy version and is not so prone to denting by applying too much pressure when installing. Clips sold separately. This premium moulding weighs 10 oz., compared to the economy deck lid moulding at 6 oz., and an original moulding at 7...

Used aluminum rear deck lid moulding / trim for the Mercury Cougar. Our used trunk lid trim is usually dull and lightly scratched as you see pictured here. Expect numerous and heavier scratches in the key hole area. We have a really hard time keeping good, straight used aluminum deck lid mouldings in stock. They are very prone to damage and many have been replaced with the 1969-70 stainless steel version which was the standard service replacement part that Ford would have sold you from 1969...

Core stainless steel deck or trunk moulding / trim for 1969-70 Mercury Cougar, including convertible. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967 - 1968 Cougar is that it will not match the aluminum corner mouldings perfectly. We offer this grade of trim for those folks that are without a core for core required items. This being a core, means that it will...

NOS anodized aluminum rear moulding / trim set for the Mercury Cougar. Rare find in NOS form and all three trim parts come with original packaging.Ford part #'s: Driver side rear quarter extension trim C7WY-6529313-A, passenger side C7WY-6529314-A, and center trim C7WY-6542512-A Normal 0 false false false EN-US X-NONE X-NONE . ...

Used anodized aluminum three piece rear moulding / trim set for the Mercury Cougar. Used driver quality set with no obvious dings or deep scratches. Better than our core sets in that they have more luster and less damage. Keep in mind these are off a 40 year old parts car.Ford part #'s: Driver side rear quarter extension trim C7WY-6529313-A, passenger side C7WY-6529314-A, and center trim C7WY-6542512-A. *NOTE* Keep in mind we buy most trim and mouldings found on a Cougar. For more insight on...