Interior

Correct color and texture, includes chromed plastic bezel. We also sell the decal only. This was used on the Eliminator / Decor or Standard Interiors but can also be used on your XR7. NOTE: These inserts came with enough studs to fit multiple cars. When installing this insert, simply clip off the extra studs you don't need.

1970 Mustang with deluxe woodgrain console insert. Fits all 1969-70 consoles, but the 1969 console insert had the seat belt storage cups. NOTE: These inserts came with enough studs to fit multiple cars. When installing this insert, simply clip off the extra studs you don't need.

This is a new reproduction available only in black. Perfect in fit and finish with the only difference from original being it does not have the sprayed on velvet-finish on the inside of the storage box. The correct lighter bezel and receptacle are included.

Used center console storage bin w/ lighter bezel. Original used unit with sprayed on velvet-finish on the inside of the storage box. 

Nice quality decal. This is for all Cougar consoles except XR7 which uses a dark burl pattern.

Used "courtesy" center dash XR-7 dash bezel plaque for the toggle switch identifiers. This item will require a touch up with a little polish and some re-painting of the lettering in most cases to make them look perfect. The stems are cut from the back so a little dab of good thick glue will hold them in place.

Used "left map" center dash XR-7 dash bezel plaque for the toggle switch identifiers. This item will require a touch up with a little polish and some re-painting of the lettering in most cases to make them look perfect. The stems are cut from the back so a little dab of good thick glue will hold them in place.

Used "panel" center dash XR-7 dash bezel plaque for the toggle switch identifiers. This item will require a touch up with a little polish and some re-painting of the lettering in most cases to make them look perfect. The stems are cut from the back so a little dab of good thick glue will hold them in place.

Used "right map" center dash XR-7 dash bezel plaque for the toggle switch identifiers. This item will require a touch up with a little polish and some re-painting of the lettering in most cases to make them look perfect. The stems are cut from the back so a little dab of good thick glue will hold them in place.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

Two required per car, early 67 used a chrome version of this screw. Later years used this screw.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Very nice reproduction cigar lighter knob for 1970 Mercury Cougar and Ford Mustang. Metal knob, screws onto your heating element.

Knob is exact replacement, element is a generic replacement. Exact replacement for 67-68 dash or 69 center console lighter and lighter socket.

Cigar lighter for all 1967-68 Mercury Cougar and Ford Mustang dash ashtray mounted locations. Additionally used on 1969 Cougar and Mustang consoles, console only, not the under dash ashtray unit.

Used cigar / cigarette lighter for the lower dash mounted ashtray unit. 1969 Mercury Cougar and Ford Mustang.

Used cigar or cigarette lighter for all 1970 Mercury Cougar and Ford Mustang. Starting in 1970 this lighter moved to the dash position that was vacated by the 1969 ignition switch.

Knob is exact replacement, element is a generic replacement. Socket and element are manufactured by the same company to insure fit. Exact replacement for 1967-68 dash or 1969-70 under dash lighter and lighter socket. Replaces Ford part # C7ZZ-15052 and C6ZZ-15055-B.*Note - Retainer should have a ground lug on it in order to work with 1969 console cigar or cigarette lighters.

Cigar or cigarette lighter for 1971-73 Mercury Cougar and Ford Mustang. Slight change from the 1970 style, this one has a black plastic shaft. Ford part # D1ZZ-15052-A.

Reproduction clevis for the tilt/tilt away steering column equipped Mercury Cougar or Ford Mustangs. This unit attaches the pawl cable to the vacuum motor shaft. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used retaining clip for the adjustment bar in the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. Two required per car, used to hold the tilt position adjustment bar in place.  * While not technically correct, this also will work for 1970 - 1974 Cougar/ Mustang tilt columns. SOLD INDIVIDUALLY*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Used clip for the adjustment tension spring for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Used dash pad clip for any 1969-70 Mercury Cougar or Ford Mustang. This clip attaches to the steel dash assembly. The lower portion of the padded dashes just above the glove box door and steering column is where they attach. We have seen anywhere from 2-4 or zero of these clips installed on 1969-70 Cougars. According to Bill Q. these clips prevent the sharp dash pad screws from coming into contact with wiring or wiring harnesses. His go-around is to only use blunt screws (without a point) for...

This clip attaches to the textured steel dash top on many 1971-73 Ford, Mercury, and Lincoln cars. Mostly full sized and intermediate cars such as Cougar, Mustang, Torino, Cyclone, Montego, Ranchero, Lincoln, and Continental. 3 of these clips are used to attach the dash top panel to the cowl at the windshield. Sold individually. Brand new AMK clip.The curved tail kind of guides the panel into the slot at the front. The illustration for this part is shown on page 48 of the 1971-72 Mustang Body...

This clip attaches to the textured steel dash top on many 1971-73 Ford, Mercury, and Lincoln cars. Mostly full sized and intermediate cars such as Cougar, Mustang, Torino, Cyclone, Montego, Ranchero, Lincoln, and Continental. 3 of these clips are used to attach the dash top panel to the cowl at the windshield. Sold individually.The curved tail kind of guides the panel into the slot at the front. The illustration for this part is shown on page 48 of the 1971-72 Mustang Body Assembly Manual....

These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

This item holds the release bale to the upper knuckle. It is different than the 67 - 69 clip although both can be used. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Door panel clips for the 1967 Standard or XR7. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

This unit has had the original movement replaced with a quartz movement. It has been meticulously rebuilt by the best in the business and features a new, crystal clear lens. $150 credit when you return your clean rebuildable core with a copy of your invoice. Quartz movement clocks have second hands that click around, original clocks had a constant sweep of the second hand. Check out the video below on our new gauge tester: ...

This is a NOS clock. The face is brilliant, it has never been mounted and is guaranteed to work good. It does have a tiny crack that is mostly hidden by the center knob which is very common for these original lenses.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

Used standard core clock for the Mercury Cougar. These standard clocks generally do not work after 40 years and are considered cores. We also offer clocks with modern quartz movements or NOS movements in restored clocks. Check out the video below on our new gauge tester: ...

This clock has had the original mechanical movement replaced with a modern, new quartz movement. You should get many years of trouble free accurate use out of this clock. The factory equipped movements were very unreliable and often quit after a couple years use. We now put a new lens in every rebuilt 1969-70 XR7 / Eliminator clock we sell. Not only has the movement and lens been changed but every part of this clock inside and out has been given attention. We have used several clock restorers...

C9ZB-15A006-B Wiring harness, or pigtail that goes from the back of the clock to the main under dash wiring harness. This wiring harness includes the 2 light sockets for the clock illumination. Ford master part number C9ZZ-15A006-A. Fits XR7 and standard Cougars. Fits 1969 Mustang.

D0ZB-15A006-A Wiring harness, or pigtail that goes from the back of the clock to the main under dash wiring harness. This wiring harness includes the 2 light sockets for the clock illumination. Ford master part number D0ZZ-15A006-B. Fits XR7 and standard Cougars. Fits 1970 Ford Mustang.

[No Description Provided]

Prepare to be disappointed... This is a reproduction 1967 - 1968 Ford Mustang clock knob and set screw (replaces Ford part # C7ZZ-15032-A) that can be cut down to work on your 67-68 standard Mercury Cougar (barely). The pictures below will guide you on this "adequate at best" solution for those of you missing this hard to find knob and set screw.Click on images to enlarge. The above picture is a good used original Cougar knob mounted on a 68 clock.  We do not have these original Cougar...

Good used knob, threads off counter clock wise from the shaft. This item will work for both Standard and XR7 models.

C9WY-15017-A Steel bracket that fastens to the rear of the passenger side dash for mounting the clock. We offer this bracket because it often comes up missing when a dash pad from a standard Cougar is transplanted to an XR7.

This reproduction stainless trim mounts over your pedal pad. Not only adds style but also holds your pad in place. Replaces Ford part number C5ZZ-7B544-A.

Sold as pair, exact copy. These also double to keep your windlace firmly in place.

These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.

Used to store your shoulder belt above the windlace on the drivers side (harder to find than passenger side). These are often rusty, missing or broken. I am not aware of any reproductions being made.

Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.

Used to store your shoulder belt above the windlace on the passenger side. These are often rusty, missing or broken. I am not aware of any reproductions being made.