Interior

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in DARK IVY GOLD or DARK GREEN for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in DARK RED for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. Please Note: Color on these is inconsistent and never spot on...

CURRENT DASHES IN STOCK ARE BLUE AND BLACK Good used original upper dash pad. The pad shown is for a 1968 but will work a 1967. The difference is the 68 has a relief cut for the aluminum VIN tag located on the passenger side and 67 did not.

Of the three covers used on the 67-73 Cougars we find this one the most difficult to use. Will Not Work On Badly Distorted Dash Pads. The problem is not with the product but rather the design of the original dash pad. Unlike the 69-73 pads the 67-68 pads are prone to warping (sagging) badly. Since this glue on shell is rather rigid you have to have a mostly straight pad to work with. Large cracks are no problem even if your pad is curling at the cracks, just break off the portions of your...

Good used textured steel dash panel, for all 1971-73 Mercury Cougar and Ford Mustang. This is the flat steel piece that the meets the windshield and houses the defroster nozzles for the windshield.  Attaches to the dash pad using (5) 45271-S36 nuts.*Note - Save your VIN tag from your original dash, you don't want to lose it.Replaces Ford part number D1ZZ-65044D90-A. ...

This used part comes carefully cut from a parts car and will include all mounting tabs. It is slightly different from the Mustang version as it has a different contour where the dash pad attaches. AC and no AC are the same, but 67 and 68 differ slightly in height of the area where the ashtray is installed.  

This used part comes carefully cut from a parts car and will include all mounting tabs. It is slightly different from the Mustang version as it has a different contour where the dash pad attaches. AC and no AC are the same, but 67 and 68 differ slightly in height of the area where the ashtray is installed.  

Excellent reproduction of the passenger side 1967-68 Mercury Standard Cougar "Cougar" dash panel emblem. Nice reproduction with locating pins that attach to the padded dash panel on the passenger side of all 1967-68 Standard model Cougars. The factory originally installed these emblems onto the padded dash panel, and melted over the pins to the back. Carefully remove the padded dash (clips or screws) and break off the melted tabs on the back of the emblem. Clean pad and reinstall the new...

Reproduction passenger side 1967-68 Mercury Cougar "Cougar XR7" dash panel emblem with chrome XR7 highlights. Nice reproduction with locating pins that attach to the woodgrain dash panel on the passenger side of all 1967-68 XR7's (excludes the special edition XR7-G models). The classic Cougar community voiced their opinion that the original emblems with satin silver was nice, but the chromed "XR 7" lettering in chrome makes the dash 'Pop' (see comparison photo above). The factory originally...

Excellent reproduction of the passenger side 1967-68 Mercury Cougar "Cougar XR7" dash panel emblem. Nice reproduction with locating pins that attach to the woodgrain dash panel on the passenger side of all 1967-68 XR7's (excludes the special edition XR7-G models). You can view the photo above for a comparison between the satin and chrome versions. The factory originally installed these emblems onto the woodgrain steel panel, and melted over the pins to the back. The rear section of that...

There are five of these on the RH side that hold your plastic dash to the metal understructure. These also hold on the map light. Sold Individually. Ford Part #: 376642-S. Reference from mercurycougar.net: Best guys to always talk to about Cougars...will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting things...

Used steel lower dash panel for all 1970 Mercury Cougar and Ford Mustang with factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. Grade A = no pitting, no extra holes. Replaces Ford part number D0ZZ-6504320.

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang with factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade B used some pitting and or  extra holes. Replaces Ford part number C9ZZ-6504320-D.

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang without factory air conditioning, this panel does not have the round holes in the outer section. This is not a reproduced part, only the 'with' A/C panel is reproduced. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade A used, no pitting, no...

Used steel lower dash panel for all 1970 Mercury Cougar and Ford Mustang without factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. Grade A used = no pitting, no extra holes. Replaces Ford part number D0ZZ-6504320.

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang without factory air conditioning, this panel does not have the round holes in the outer section. This is not a reproduced part, only the 'with' A/C panel is reproduced. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade B used, may have...

Used steel lower dash panel for all 1970 Mercury Cougar and Ford Mustang without factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. Grade B used = some pitting and or extra holes. Replaces Ford part number D0ZZ-6504320.

Reproduction heater dash plate for the 67 Cougar or Mustang. Included are the plate, 4 piece knobs and hardware. Keep in mind that this face plate has the pebble grain finish which was standard to Mustangs (Cougars had the smooth finish).Replaces Ford part number C7ZZ-18A651-B

Reproduction heater dash plate for the 68 Cougar or Mustang. Included are the plate, 4 piece knobs and hardware. Keep in mind that this face plate has the pebble grain finish which was standard to Mustangs (Cougars had the smooth finish).

Used switch panel for most 1971-73 XR7 convertibles. Panel holds 3 different toggle switches: COURTESY - MAP - TOP. All came painted black with the camera case finish with the indicated switches as shown. Most will be nearly pit free as shown but will need a spray of black paint for that 'extra' detail prior to installation.  *Note excludes all coupe or hard top Cougars, and non-XR7 convertibles.Replaces Ford part number D1WY-7604338-A.

Used switch panel for most 1971-73 XR7 hard tops. Panel holds 3 different toggle switches: COURTESY - MAP - R.DEFOG. All came painted black with the camera case finish with the indicated switches as shown. Most will be nearly pit free as shown but will need a spray of black paint for that 'extra' detail prior to installation. This panel does have a small hole above the defog switch for the red indicator light. Red indicator light sold separately. *Note excludes convertible and those Cougars...

Used switch panel for most 1971-73 XR7 hard tops. Panel holds 3 different toggle switches: COURTESY - MAP - ACCY. All came painted black with the camera case finish with the indicated switches as shown. Most will be nearly pit free as shown but will need a spray of black paint for that 'extra' detail prior to installation.*Note excludes convertible and those Cougars with the heated back lite or rear defog option.Replaces Ford part number D1WY-6504338-A.

This rectangular trim part is located on the right side of the glove box on all 1967 - 1968 Mercury Cougars without factory installed AC. This could be referred to as a passenger side AC vent block off plate. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as-is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color.

This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these. Sold as a Pair. Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...

Replaces Ford part #C8AZ-6223362-A. Sold in pairs, four required per car, used on most Ford products. We often get calls like "How do I remove my front window cranks?" Unlike the rear cranks that are held on by an Allen set screw, the fronts have a Phillips screw under this decal. If you are careful, often you can reuse your original and glue it back in place.

Used on both the speedometer and temperature / fuel gauge. Comes with plastic keeper washer that connects it from the backside of the lens. Sold individually, two required per cluster. These are in used condition as shown and need restoration.

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing, good chrome on the male buckle and it may even have the date code tag still in place. We will try to obtain the correct date code if...

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models. This is a fully functional retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for...

Grade A used deluxe shifter handle in black. Nice used condition, minor cracks in the plastic on the bottom. No release button or set screw included. Fits 1967 Mercury Cougar XR7 and 1967 Ford Mustang with IDG or Interior Decor Group and all Shelby Mustangs with automatic. This one year only, T handle, has concave or recessed buttons.  Ford part number C7ZZ-7213-A. We know that Scott Drake is using this number for 4 speed manual knobs, which was a made up Ford part...

Grade A used deluxe shifter handle in black. Nice used condition may have a hairline crack in the plastic on the bottom. No release button or set screw included. See related items for Grade B  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Grade B used deluxe shifter handle in black. Fair used condition, cracks in the plastic. No release button or set screw included. Fits 1967 Mercury Cougar XR7 and 1967 Ford Mustang with IDG or Interior Decor Group and all Shelby Mustangs with automatic. This one year only, T handle, has concave or recessed buttons.  Ford part number C7ZZ-7213-A. We know that Scott Drake is using this number for 4 speed manual knobs, which was a made up Ford part number on their part. We...

New old stock deluxe shifter handle in black. Perfect condition, no cracks in the plastic. No release button or set screw included. NOS Fits 1967 Mercury Cougar XR7 and 1967 Ford Mustang with IDG or Interior Decor Group and all Shelby Mustangs with automatic. This one year only, T handle, has concave or recessed buttons.  Ford part number C7ZZ-7213-A. We know that Scott Drake is using this number for 4 speed manual knobs, which was a made up Ford part number on their part. We...

Grade B used deluxe shifter handle various colors. Please specify color in the notes, limited to stock on hand. Fair used condition will have at least one crack in the plastic. May also have slightly pitted chrome. No release button or set screw included. See related items for Grade A  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Used diffuser for the shift indicator lamp. This diffuser is used on the Cougar or Mustang WITH a console and attaches to the end of the light socket on your shift indicator wire harness. Both shift indicator lamps with or without a console used the same wire harness and socket, but used different diffusers. The difference in the harness from the 67 to the 68 was different colored wires and different plugs. Replacement bulbs can be found on our site as well. ...

Used diffuser for the shift indicator lamp. This diffuser is used on the Cougar or Mustang WITHOUT a console and attaches to the end of the light socket on your shift indicator wire harness. Both shift indicator lamps with or without a console used the same wire harness and socket, but used different diffusers. The only difference in the harness from the 67 to the 68 was different colored wires.

Made from clear acrylic plastic with prisms added to increase the bulb brightness.Ford originally used white nylon with no prisms, which makes the light very dull. Replaces Ford Part # D1AZ-13783-B.

Great fit. There were two different mounting tab styles used in the 1970's, this one is 100% correct for the 1971 Standard Hardtop Cougar manufactured before 6/71 and fits the early 1971 housing we sell. Ford Part # C6OZ-13783

This was used on many Ford products but this bezel is 100% correct for the 1971 - 1973 Standard Hardtop Cougar manufactured after 6/71, but will also work for all 1971 - 1973 Cougars or Mustangs if you purchase the matching Bezel. No Cougar had a dome light in 1967-70. Ford Part # D1AZ-13783-B.

Nice chrome finish. This was used on many Ford products but this bezel is 100% correct for the 1971 Standard Hardtop Cougar manufactured before 6/71. No Cougar had a dome light in 1967-70. Ford Part # D0AZ-13788-A.

Nice chrome finish with Bulb. This was used on many Ford products but this bezel is 100% correct for the 1971-73 Standard Hardtop Cougar manufactured after 6/71, but will also work for all 1971-73 Cougars or Mustangs if you purchase the matching dome lens. No Cougar had a dome light in 1967-70. Ford Part # D6UZ-13788-A.

Used door / lid for the glove box in the Mercury Cougar, grade "A". This is just the bare inner and outer door / lid and does not come with the hinge, liner, lock or lock bezel. To prevent damage to the plastic glove box door, the inner steel backer should be removed and file 1/16" off of one or both sides. Cracking is due to shrinkage of the plastic glove box door over time. Standard model Cougar, not for XR7.Plan on painting to match your interior. Ford part # D1WY-6506024-A for the inner,...

Used door / lid for the glove box in the Mercury Cougar, grade "B". This is just the bare inner and outer door / lid and does not come with the hinge, liner, lock or lock bezel. To prevent damage to the plastic glove box door, the inner steel backer should be removed and file 1/16" off of one or both sides. Cracking is due to shrinkage of the plastic glove box door over time.Plan on painting to match your interior. Ford part # D1WY-6506024-A for the inner, D1WY-6506024-B for the outer. ...

Used door / lid for the glove box in the 1967 Mercury Cougar or Ford Mustang. This unit is just the bare door / lid and does not come with the hinge, liner, lock or lock bezel. We have found this door on 1967 and into 1968 Cougars. Sometime in early 1968 this glove box door came with three holes on the back. Both glove box doors fully interchange. Bead blasted for the photo, door ships without rust, in most cases you will want to paint prior to installation.Ford part # C7ZZ-6506024-A.*NOTE*...

Used door / lid for the glove box on any 1968 Mercury Cougar or Ford Mustang. This unit is just the bare door / lid and does not come with the hinge, liner, lock or lock bezel. We have found this design of door with the 3 holes, well into the 1968 production run. 1967 and early 1968 doors are typically without the three holes on the back. Both glove box doors fully interchange. Bead blasted for the photo, door ships without rust, in most cases you will want to paint prior to installation.Ford...

Used door / lid for the glove box in the Mercury Cougar or Ford Mustang. This unit is just the bare door / lid and does not come with the hinge, liner, lock or lock bezel. Dent free, may have minor surface rust. Ford part # C9ZZ-6506024-A.

Used door / lid for the glove box in the Mercury Cougar, grade "B", with at least one crack, or an extra chip or scrape. This is just the bare inner and outer door / lid and does not come with the hinge, liner, lock or lock bezel. To prevent damage to the plastic glove box door, the inner steel backer should be removed and file 1/16" off of one or both sides. Cracking is due to shrinkage of the plastic glove box door over time.Plan on painting to match your interior. Ford part # D1WY-6506024-A...

Used door courtesy light lens on the 67 - 70 Cougar. Because of the heat and placement of the bulb behind this lens, they were prone to burning or in some cases melting. This lens is easily replaceable by removing the two screws holding the housing together and grinding off the studs holding the lens and reflector in place. You can secure them back in place with small amount of epoxy. You can also find the reflector lens here. Right is same as left, sold individually. ...

Used door courtesy light reflector used on 67 - 70 Cougars. This lens is easily replaceable by removing the two screws holding the housing together and grinding off the studs holding the lens and reflector in place. You can secure them back in place with small amount of epoxy. You can also find the light lens here. Right is same as left, sold individually.