Interior

Automatic shifter arm pawl - late version. Mounts inside the bottom of the shifter arm in the slot with the cable and spring. Fits original chromed shifter levers or arms 1970-73 Mercury Cougar and Ford Mustang. The early pawl has a key with a thickness of 0.100", the later (1970ish-73) with a thickness of 0.159". Check your shift lever for the size that you need. Ford part number D0ZZ-7C442-A.We also list the early version. Check out our video on rebuilding your...

Adjustable rod that connects the floor shifter to the "Select-Shift-Merc-O-Matic" automatic transmission. C4 transmissions only, code "W" on your door data plate tag. Small block 289/302 engines received the C-4 automatic transmissions. Rod marked C7ZA-7326-B. Shift rod approximately 17-1/4 inches long. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the "Select-Shift" automatic transmission. C4 transmissions only, code "W" on your door data plate tag. All 302 and 6 cylinder engines received the C-4 automatic transmission. Rod with casting number C9ZA-7326-D. Shift rod approximately 17-1/4 inches long. 1969 Ford Mustang only. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the "Select-Shift" automatic transmission. FMX transmissions only, code "X" on your door data plate tag. All 351 engines received the FMX automatic transmission. Rod with casting number D0ZA-7340-A. Shift rod approximately 18 inches long. Ford part number D0ZZ-7326-D. 1970 only. Check out our video on rebuilding your shifter below: ...

Reproduction adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions.Includes pin and nut. Shift rod approximately 18 inches long. Replaces Ford part number marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions. Shift rod approximately 17 inches long. Rod marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the "Select-Shift" automatic transmission. FMX transmissions only, code "X" on your door data plate tag. Most 351-2V engines received the FMX automatic transmission. Rod originally had a "Yellow" paint daub for identification purposes on the Dearborn assembly line. Shift rod approximately 18-1/2 inches long. Rod stamped D1ZA-7340-AA. Check out our video on rebuilding your shifter below: ...

This hard plastic part slips over your floor shifter stem and keeps coins and such from falling inside your center console. Replaces Ford part number C7ZZ-7C445-A. Check out our video on rebuilding your shifter below: ...

This never came on a Cougar, but it is a nice upgrade from the string that attaches your seat belt shoulder strap to the coat hanger when the shoulder strap is not in use. Fits all models except convertible. Originally, the shoulder strap connected to the bolt cover on one end, And to a string on the shoulder strap that connects it to the coat hook to keep it out of the way when not in use. This new hook slides into the track on the back of the moulding over the door, and is used instead of...

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

Reproduction cigar or cigarette lighter socket and retainer assembly for 1971-73 Mercury Cougar and Ford Mustang. Also available with lighter, see related items.Ford part # D1ZZ-15052-A.

Good used light used only on the 1967 automatic consoles. The only difference between this shift indicator light without console and with console is the diffuser. The diffusers pull off and interchange. This light harness is also known as the PRNDL light harness (park, reverse, neutral, ...). If you choose to run the light without the diffuser it will shine bright as opposed to a warm glow.  Ford Part Number: C7ZZ-15A808B Fits 67 CougarFits 67 Mustang Check out our video on rebuilding...

Reproduction light used only on the 1967 automatic consoles. The only difference between this shift indicator light without console and with console is the diffuser. The diffusers pull off and interchange. This light harness is also known as the PRNDL light harness (park, reverse, neutral, ...). The 1967 light had a male / female black combination plug. If you choose to run the light without the diffuser it will shine bright as opposed to a warm glow. Ford Part Number: C7ZZ-15A808B Check out...

Bulb and socket assembly that attaches to the back side of your instrument cluster housing on all 1968 Standard model Cougars. All electrical harnesses are inspected, professionally repaired (when needed), tested, and ready to install. Harness marked C8WB-10B942-E.Check out the video below on our new gauge tester: ...

Bulb and socket assembly that attaches to the back side of your instrument cluster housing on all 1968 XR7 model Cougars. All electrical harnesses are inspected, professionally repaired (when needed), tested, and ready to install. Harness marked C8WB-10B942-J.Check out the video below on our new gauge tester: ...

Reproduction sound deadener for the seat divider on the 1967 - 1970 Mercury Cougar. This reproduction is as close to the original as possible, and is comprised of a mastic material. This item is trimmable and will fit bot the 67 - 68 and 69 - 70 seat divider.

This is the same sound deadener kit that everyone else is offering, but if what you are looking for is a kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least...

If what you are looking for is a sound deadener kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least this listing will give you an honest idea of what you are...

This is the exact same cut of sound deadener as the tar based sound deadener, but cut out of the foil heat shield rather than the paper backed tar. The foil heat shield weighs over 20 Lbs less than the paper backed tar when cut into the same pattern. This makes shipping this over seas much more affordable than the paper backed tar version of the underlayment kit.For a super cheap version of this insulation, try this item: foil insulation ...

5/16" thick sound deadening and heat reflecting material, comes in a 4' X 6' sheet that can be cut to fit. This insulation consists of two layers of polyethylene bubble film sandwiched between two layers of aluminum foil. Temperature range rated -60 deg. F. to 180 deg. F. Combining this with the tar-based sound deadener underlayment will result in similar sound deadening as the OEM sound deadener.Below is listed how many rolls you will need to underlay the sections of a Cougar:  Area...

Reproduction 7 Piece sound deadener underlay for the the 71 - 73 Convertible Cougar.

Reproduction 5 piece sound deadener underlay for the 71 - 73 Cougar Coupe

This is the same kit everyone else is offering, but if what you are looking for is a kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least this listing will give...

This is the same sound deadener kit that everyone else is offering, but if what you are looking for is a kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least...

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange.  *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange. Ford part # C9SZ-3C708-A.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.

We claim that in time every nut bolt and clip will be documented on this site! Here is yet another tiny little, one year only trivial part that only the most detailed enthusiast will even care about. This little part is designed to space the column cover away from the metal lower dash so as to prevent dash squeaks. They are left natural, never painted (the one shown has surface rust). Two are required per car, they are sold individually. These little parts are often missing and of course not...

Good used and working speedometer from 1969-70 standard model Cougars. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the comments section of your order. Good used unit that is not overly faded and guaranteed to work correctly. 1969 and 1970 standard speedometers all look exactly the same on the front, but the 1969 is white backed, and most of the 1970 ones are bare steel color. Replaces...

Used 1967-68 Mercury Cougar XR7 speedometer with trip meter, grade B condition. Grade B will be fully functioning, in most cases the trip meter numbers will be worn and not easy to read.  Put your desired odometer range in the comments section, and we will try and match it up as close as possible.Check out the video below on our new gauge tester: This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an...

Good used and working speedometer from 1969-70 XR7's and Eliminators. Grade A used, tested and will have good numbers on the odometer section. (Our Grade B examples are fully functioning, but will have worn numbers on the odometer section. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the comments section of your order. Good used unit that is not overly faded and guaranteed to work...

Good used and working speedometer from 1969-70 XR7's and Eliminators. Grade B used, tested and will have faded or missing numbers on the odometer section, generally the dials look black where the white numbers have worn or faded off. (Our Grade A examples are fully functioning, and will have legible numbers on the odometer section. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the...

Good used lens that has not gone milky from over exposure to the sun. Used only on the 69 - 70 XR7 speedometer. To get these lenses looking new you will have to use a three step plastic polish like Novus or Meguires plastic polish. If your lenses are cloudy or swirled looking this will not come out as it is internal.

This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original decal with starburst design. Spring is included. Check out our video "All about seat belts" below.

Better quality than our reproduction for less money. Ford part number C0DZ-13807-A.

Spring that fits into the steering column collar. Two springs in total that hold your key lock cylinder in place. Two required per car.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Spring used to apply tension to the tilt locking pawl. 1967 thru 1969 required two springs due to the tilt away function. 1970 and later required only one spring.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This gives the thumb release button in your T shaped shift handle its tension. If it is rusted then your button will not return back to its outer position easily. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Technically this spring fits all Ford and Mercury floor shifters 1965-73. Ford part number C5ZZ-7C300-A. The MPC shows this spring to have a free length of 2-1/16 inches.

Used steering wheel tension spring used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. Keeps tension on the steering wheel shaft so as to keep the steering wheel from contacting the upper column cover. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC...

Easy to replace, keeps correct tension on your gas pedal.

Replacement throttle pedal spring for your 71 - 73 Cougar or Mustang. Easy to replace, keeps correct tension on your gas pedal.

Used spring cap that is used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Don't try to straighten your rod if it looks like this. The contour seen here is correct. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.