This reproduction hood latch support screw kit fits both the Standard and XR7 and is sold as a set of 4.

Reproduction Instrument Finish Panel Cluster Screws for the 1967 and 1968 Mercury Cougar

Fits 1967 Standard or XR7

For the 1968 but will fit both 1967 and 1968 Standard or XR7 Cougars or Mustangs

Original Ford style fasteners used on most all Ford products starting in 1968. Sold in pairs. Zink (dark silver)

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

Fits 1967 Standard or XR7 Sold as a Set as Pictured. Similar to 1968, 1968 has a pair of longer screws for the reinforced 1968 rear panels.

Fits Standard or XR7Sold in a pack of 8 screws

Fits Standard or XR7. Sold as a pair.

Set of 4 new phillips oval head mounting screws with black finish for all 1967-68 Mercury Cougar automatic shifter bezel mounting plates without console and XR7-G bezels. Also fits 1965-68 Ford Mustangs with automatic transmissions and without consoles. Check out our video on rebuilding your shifter below: ...

Set of 4 screws for mounting the automatic shifter adapter plate on all 1967-68 Mercury Cougars without console. Also fits 1965-68 Ford Mustangs without console. Check out our video on rebuilding your shifter below: ...

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

Fits 1967 and 1968 Standard or XR7

Set of 11 black pan head screws for fastening the taillight bezel to the taillight housing on the 69 - 70 Cougar. This set is enough to do one bezel. If you bought the reproduction 69 or 70 taillight bezels, remember that they don't come with screws. Earlier year taillight bezels used mounting studs, but the 69 - 70 bezels screwed in from the housing to the bezel. This is a common #8 x 1/2 panhead screw that can be found at your local hardware store brand new. ...

Set of 11 screws for fastening the taillight bezel to the taillight housing on the 69 - 70 Cougar. This set is enough to do one bezel.If you bought the reproduction 69 or 70 taillight bezels, remember that they don't come with screws.Earlier year taillight bezels used mounting studs, but the 69 - 70 bezels screwed in from the housing to the bezel. This is a common panhead screw that can be found at your local hardware store brand new.

These self-tapping screws attach the cardboard taillight protectors to the body, inside the trunk. Fits 1967 and 1968 Standard or XR7, sold in set of 4.

These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Sold individually and four are required per car. Replaces Ford part #: C9ZZ-6522204. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Fits 1967 and 1968 Standard or XR7. Holds "J" shaped plastic hinge covers in place.

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 4 total per car, all 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped for the front seat belts inboard on 1971-73 cars. Round anchor bracket with factory welded nut for added strength. See related items for good used seat belt anchor plates if you have concours needs. Replaces Ford Part # D1AZ-6561216-A. ...

Good used original seat belt bolt. There were a few different variations of this bolt, some were stamped with a B and others had no stamping at all. 13/16" hex head, 1-1/2 inch bolt with a 3/16 inch shoulder. 

Complete set of front seat belt bolts for your 67 - 68 Cougar or Mustang. Included are the 4 bolts, 4 large washers, 2 spacers and 4 rubber anti-rattle gaskets. Get the rear set here.

Reproduction set of front seat belt bolts for your 69 - 70 Cougar or Mustang. Included are the 4 bolts, 4 large washers and 4 anti rattle gaskets.

Complete set of rear seat belt bolts for your 67 - 68 Cougar or Mustang. Included are the 4 bolts and 4 spacers. Get the front set here.

Fits 1968 Standard or XR7

Fits 1967 - 1973 Standard or XR7. Pins not used on 71-73 buckets.

Fits 1968 - 1970 Standard or XR7

New 8-32 set screw for the rear window crank handles. Fits 1968-70 Mercury Cougar and Ford Mustang. Allen hex size of 5/64".

Missing some of the hardware used to bolt on your shock tower braces? Here are our reproduction shock tower brace mounting kit for the Mercury Cougar or Ford Mustang.

Driver side bracket that fits onto the rear radio bracket assembly on the 67 - 68 Cougar or Mustang equipped with a console. The bracket assembly is 3 separate pieces, this is for the driver side bracket only.

Passenger side bracket that fits onto the rear radio bracket assembly on the 67 - 68 Cougar or Mustang equipped with a console. The bracket assembly is 3 separate pieces, this is for the passenger side bracket only.

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out this video Still have riv-nut questions? Here are riv-nut answers! ...

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

Reproduction Small Block Intake Manifold Bolt for the 1968 -1969 Mercury Cougar - 1968 -1969 Ford MustangSold individually 

Reproduction Smog Pump Pully Bolt for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually 

Reproduction  Lower Windshield Moulding Center Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Used spacer for the lower windshield moulding

Reproduction  Lower Windshield Moulding Fender Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.

Keeps spark plug wires neat and orderly. Mounts on valve covers. Replaces Ford Part #: B8Q-12297-A.

Made of heat resistant black nylon. Keeps spark plug wires neat and orderly.

This clip holds the speedometer cable gear to the end of the cable. Replaces Ford Part # : C1DZ-17292

Show quality, correct weight and markings. Sold individually.

This clip is the same as a door panel clip with the exception that it does not have the foam spacer. This clip was used on the 1968 XR7 overhead console, 1967 - 1968 xr7 and standard model upper and lower console pads, seat back access panels and several other applications. This original clip holds tighter than the reproduction. We recommend using this used clip over our reproduction for applications like the seat back because the reproductions often do not cut it. Ford part number...

Spring nut used to install the fan shroud on a 1967-71 Cougar or Mustang, 4 per car.