Your cart is empty!
If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Pair of bolts for installing the fuel pump on most V-8 engines. 289, 302, 351W, 390, 427-4V, and 428CJ. AMK bolts 3/8-16 x 1-1/2 inches. Sold as a pair, for installation of mechanical fuel pump into the timing covers. AMK F-519. 43530-S8.
Set of 12 bolts for the intake manifold on any factory 1966-67 Ford 289 engine. AMK F-478.*Note - Excludes 1968 289 and 302 engines.
New old stock distributor upper replacement bushing for any factory 289, 302, Boss 302, 352, 390, 406, 427, 428, 428CJ distributors. Limited quantity on hand, Ford part number B8AH-12120-A. Inside diameter 0.467", outside diameter about 0.687". Length 1.757". These are pressed fit, please take care when removing and replacing. Our limited research shows that this bushing will fit the above distributors. However, we can only say that for 302 engines, you are good up until...
Used distributor clamp with bolt, for any 260 / 289 / 302 / 351W / 351C / 429CJ built from 1963-1973. May come with either an original used bolt or the new bolt made by AMK Products. Ford part number C3AZ-12270-A.
Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. If you're...
Used coil mounting bracket. This version of the bracket is probably the most common. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. This version has the notch as shown. We know that this version was used on...
Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the market. ...
Hot idle compensator valve assembly for many Ford engines with PCV, starting in 1964 through early 1968. Typically found on 1964-66 Ford 260-2V, and 289-2 engines with air conditioning. 1967-68 289-2V, 302-2V and some 390 engines all with air conditioning and PCV or closed emissions. The Ford assembly manual indicates that the Hot Idle Compensator Valve 'T' Assembly, was installed by removing 3/4 inches of the PCV hose, 2-1/4 inches (on center of the PCV valve). See picture for clarification....
Crankshaft oil slinger for all small block Ford V-8's, starting 1963 until at least through 1973. 1963-68 289 and 289 HiPo engines. 1968-73 302 engines, 1969-70 Boss 302 engines, 1969-73 351W engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter about 2-7/8 inches. Ford part number C3OZ-6310-A.
Single cylinder head from 1967 Mercury Cougar with non smog 289 engines, 289-2V and 289-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 54-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.3:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C6OE-M or C6OE-6090-M.These weigh...
Single cylinder head from 1967 Mercury Cougar with California smog 289 engines, 289-2V and 289-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 54-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.3:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C6OE-M. *Note - These...
Fuel pump drive eccentric for most small block Ford engines 1963-72. Including 221, 260, 289, 302, and 351W. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 2-1/2 inches in diameter.Ford part number C3AZ-6287-B.
Fan spacer, measuring 2-7/8 inches, sometimes mentioned as 3.15" overall. Applications include 1967-68 Mercury Cougar and Ford Mustang with 289/302 and standard cooling. Reference number YA-79.Ford part # C5OE-8546-A, Ford engineering # C5OZ-8546-A.
Fan spacer, measuring 3-1/16 inches, sometimes mentioned as 3.40" overall. Applications include 1967 Mercury Cougar and Ford Mustang with 289-4V. Reference number YA-78.Ford part # C5AE-8546-B, Ford engineering # C5AZ-8546-B.
Oil filter adapter for all Ford small block engines including 221, 260, 289, 289HiPo, 302, and 351W engines. Ford indicates that this was used 1962-1970. Screws into the engine block. We do not know the threads, but the small side is standard oil filter sized.Ford part number C2OZ-6882-C.
Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.
Brass and steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown.
Steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown.
New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.
Make those horns sound like they should! These relay kits work just like my headlight relay kits to deliver full system voltage to your horns. Ford used horn relays on many vehicles into the early seventies. Unfortunately Mustangs after '65 and Cougars never had them. These Heavy duty relays are C4AZ-13853 replacement units modified for use on our classic cars.Included in kit: Relay, wiring harness and instructions.Benefits: Easy to install with no cutting of your original harness. Mount the...
Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP
Hex shaped extension. Made from machined metal and Zinc plated. Replaces Ford Part # : C2OZ-9B339
Hex shaped extension. Made from machined metal. Used and road tested steel extension for installing your oil pressure sending unit. Part shipped normally will not be as clean as the one pictured, we strongly suggest cleaning the inside oil passage prior to installation, it is a used part. Fits all 289, 302, 351W, 390, 427, 428CJ engines. Please note that the 351C or 351 Cleveland engine has the it's oil sending unit screwed directly into the block and the location is at the rear top....
New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons, radiator support, transmission, rear end housing, sheet metal, glass and variety of other parts. It's often little details like this that separate first and second place at the show.
A needed part for giving your car a tune-up. PCV Valve fits all years; 289, 302, 351, 390, and 428 CID; V8. *Note - Not technically correct for 390-4V or 428CJ, those originally used a PCV valve with a threaded top, and the 90° elbow - part number C7OZ-6A706-A.
NOTE* After comparing to the original pulley, we've found that this reproduction is approximately 3/16" shorter in overall height. New crank shaft pulley, single sheave small block Ford 289 / 302 351W engines up to 1969. Single V-belt or fan belt pulley, means for use with only the alternator. Not for use with power steering, air conditioning, or smog pump. Measures just under 6-1/4 inches in diameter. Single sheave crank shaft pulley with 3 bolt holes, excludes engines after 1970....
Four needed per fan shroud. While not technically correct, some like the black screws over the silver because it better matches the radiator and shroud. Hexwasher Head #14 X 5/8 Tapping Screw Ford Part Number: 31498-S
New slotted pan head screw for mounting distributor points or condensers. Three total, per single advance Ford distributors. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x9/32". Sold individually, but you likely need 3.
New slotted pan head screw for mounting distributor vacuum advances. Two total, per Ford distributor. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x1". These are phosphate dipped. Sold individually, but you likely need 2.
Aluminum casting, made in the U.S.A. Exact copy of original, including part numbers. Fits any small block Ford 260/289/302/351W but would have only been correct on 1967 Mercury Cougar and 1965-67 Ford and Mustang with 289 engines. Has natural cast finish as original. Does not have the provision for the thermal vacuum switch starting in 1968 and newer small block Ford V-8 engines. Replaces Ford Part #: C5OE-8592-A For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check...
Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1967 Mercury Cougar and 1964 - 1967 Ford Mustang with 289 engines. Ford part number C5ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.
Used timing chain cover with casting number C5OE-6059-A, for any 1965-67 289 engine. 1967 Mercury Cougar and 1965-67 Ford Mustang. This timing cover has a built in timing pointer as part of the casting. Cast aluminum construction without excessive damage. Find the installation bolt kit here. Replaces Ford part number C5OE-6059-A.
Used timing chain cover with casting number C3AE-6059-A, for any 1967 390 engine. 1967 Mercury Cougar and 1967 Ford Mustang. Cast aluminum construction without excessive damage. Installation bolt kits also avialable.Replaces Ford part number C3AE-6059-A.*Note there is a different version of this timing cover for 1968-70 390/428CJ engines.
Set of 6 bolts for installing an OEM Ford timing cover marked C5OE-6059-A, which originally came on all 1967 Mercury Cougars with 289 engines or 1965-67 Fords including Mustang with 289 engines. 5 short and 1 long bolt in this kit.
Reproduction high quality chrome calve covers. Designed to fit small block engines. OE on 64 - 66 HiPo "K" engines. Will also fit the 302. These were actually used on the 65 - 66 Mustang but some folks like to use them on the Cougar because of their clean no nonsense look. Keep in mind this pair requires the push on oil cap, not the twist on. Sold as a pair. ...
Good used, working vacuum advance, comes with the hard to find threaded vacuum nipple. Ford Part Number C5AZ-12370-A
Water pump pulley 1 sheave, about 6.11 inches. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches. Application include 1967 Cougar with 289. 1969 Cougar and Mustang with 390-4V. Also various Mustangs 1965-67, all with 289.Replaces Ford casting number C5OE-8509-A.
Used brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 2 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster. Replaces Ford part number C6AZ-9A474-A.
Used brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 3 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster. Bob Mannel's book indicates that this vacuum fitting was for A/C and Thermactor smog. Replaces generic Ford vacuum fitting part number 9A474.