Heater Components without Air Conditioning

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars without factor air conditioning. Cars with only the heater option had dual fresh air vents. This bezel is for the driver side fresh air vent register and control cable, it has a molded hole for the vent cable.Replaces Ford part number D1WB-65044A13-AC (cast on the part) or D1WY-6504393-A.

Chromed plastic driver side fresh air "Vent" bezel. Mounts with the cable through a hole in the dash panel, just to the right of the vent register. Most all of these used bezels have a defect in the chrome plating along the bottom, not visible when installed.Replaces Ford part D1WA-18A405 (casting in the part), or D1WY-10852-B.*Note - Does not fit Mustang

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

Reproduction heater blower motor for Mercury Cougar and Ford Mustang that is a high quality replacement part at a reasonable price. However, these off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the...

Used heater blower motor for 69 - 70 Mercury Cougar and Ford Mustang. The reproduction off-shore motors may or may not prove to be as good of value as these good used original FoMoCo motors. To date, all we can find for these cars are foreign made units. Keep in mind our used motors carry a one year warranty and the new motors have a 30 day warranty. Also know that the mounting plate is included for free just for the asking on these used motors. We personally have never used the reproduction...

Concourse correct 3" long nipple that installs in the water pump, with the correct plating.C8OZ-18599-A.

These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing.Ford part # C7ZZ-6501891.

These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing, very tough part for us to keep in stock. The metal version is a better part and you can get our metal reproduction unit right here!Ford part # C7ZZ-6501891. ...

Heater cable for Cougars and Mustangs that are not equipped with factory air conditioning. Ford Part #: D1ZZ-18518-A

Under dash bracket used to mount the pull cable for the fresh air vent on the driver side of your Mercury Cougar or Ford Mustang.

Used mounting and indexing bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket goes behind the dash panel and keeps the vent cable attached and indexed correctly. A 7/16-14  hex nut is also needed for mounting the cable. (Sold separately)Replaces Ford part number D1WY-6501822-A.

Used mounting bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket mounts to a tab on the fresh air vent, and keeps the cable stationary.  Replaces Ford part # D1WY-18C587-A.

Used steel bracket for mounting the passenger side fresh air vent cable to the bottom of the dash below the glove box. 1971-73 Mercury Cougar only.Replaces Ford part # D1WA-6501861-AC.*NOTE* Does not fit Ford Mustang.

Reproduction heater cable set for your beloved Cat or Pony. This set is an exact fit! Replaces Ford part # C7ZZ-18518-A. *Customer Feedback*     "My first deal with Don was clear back in the 1980's and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you...

Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.

Used rear window defog switch and knob assembly with mounting bracket for the 71 - 73 Standard Cougar.

Used fresh air vent duct found behind the driver side dash panel of all 1971-73 Mercury Cougar without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1WY-6501878-A.

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "A" part and may have one very minor defect. This part will be damage free. Replaces Ford part number C9ZA-18C366-A.

Lower heater duct to floor outlet for Cougars or Mustangs with air conditioning. Used grade "B" part that will have minor defects. It will have cracks or chips. Almost half the price of the grade "A" piece and works awesome if you don't have one at all. Want to have directed heating, we've got you covered. Replaces Ford part number C9ZA-18C366-A.

C9ZA-18C433-C lower heater duct to floor outlet for Cougars and Mustangs without air conditioning. Used grade "A" part and may have one very minor defect. This part might have a small crack, but it will not have any broken or missing tabs. It's good, it's cheapish, you want it.

D1ZA-18C433 lower heater duct to floor outlet for 1971-73 Mercury Cougar and Ford Mustang without air conditioning. Used grade "A" part and may have one very minor scuff. Ford number D1ZA-18C433-AD

High Quality cloth wrapped heater duct hose. This is the correct length for most cars, but will need to be cut for proper fit in some applications. Hose diameter: 2 1/2"

This elbow is zinc plated for years of reliable service and is for 351, 390, and 428 engines. Replaces Ford Part #: D0AZ-18599-A.

Silver zinc finishDiameter 5/8"Fitting 3/4"

These beautiful reproductions replace rusty and corroded originals. 5/8" Replaces Ford Part #: C6AZ-18599-C

These beautiful reproductions replace those rusty and corroded originals that just look nasty. 5/8" Replaces Ford Part #: C6AZ-18599-B

These beautiful reproductions replace rusty and corroded originals that just look nasty.5/8" Replaces Ford Part #: C6AZ-18599-S

These bright beautiful reproductions replace those corroded and rusty originals that just look nasty. Replaces Ford Part #: C8AZ-18599-C

Reproduction water inlet elbow for your 1968 big block Cougar or Mustang.Replaces Ford Part #: C8AZ-18599-AClick on images to enlarge. ...

New clear plastic lens or face plate for the heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!

New clear plastic lens or face plate for the heater control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

New clear plastic lens or face plate for the heater control on all 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use...

New clear plastic lens or face plate for the ultra rare Power Ventilation option, heater control with power vent on all 1969 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. The Power Ventilation option added a center vent to the dash as was found on factory air conditioning cars.  Just more outside air circulation.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff...

Metal fan wheel or squirrel cage for any 1967-68 Mercury Cougar or Ford Mustang with heater only. Dimensions 4-1/4 inches in diameter and 2-1/2 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.

Metal fan wheel or squirrel cage for any 1967-73 Mercury Cougar or Ford Mustang with factory air conditioning only. Dimensions 5-3/4 inches in diameter and 4-1/8 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.

Reproduction flexible duct end that was originally stapled to the passenger side fresh air duct, found behind the passenger side dash panel of all 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1ZA-18C305-AB.

Used fresh air vent found in the driver side kick panel of all 1971-73 Mercury Cougar without air conditioning. Replaces Ford part number D1WY-6501935-A.

Complete air vent assembly with cable, knob and bracket ready to bolt to your cowl. Replaces Ford Part # : C7ZZ-6501934-A

Our good used vents will not have cracks in the plastic or a rusty flapper from a leaking cowl. These are the same for AC and non AC.Replaces Ford part number C7ZZ-6501935-A.

New set of floor kick panel fresh air vent gaskets / seals for all 1969-1970 Mercury Cougars and Ford Mustangs. Die cut gasket copied from originals that have mounting holes in them. These foam gaskets are 1/4 inch thick. Casting number as seen on seal reads C9ZA-18B290-D. Replaces Ford part # C9ZZ-6501999.

Reproduction heater blower motor for Mercury Cougar and Ford Mustang. Wiring will need to be spliced into your existing wiring harness. Save the squirrel cage and the heater motor mounting plate from your old unit because it is not included with this item.These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units....

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Due to the age, there may be a minor stress crack or blemish, it will be a good used assembly. Note that this does not come with a fan assembly, so you will need to reuse your old one. Heater core IS NOT INCLUDED. This icon means that we're looking to buy this part!WCCC is a...

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). The pictures in the sequence above are reference pictures, grade B boxes will have cracks or breaks. Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Save your old fan motor and plate, this unit does not come with a fan assembly. Grade B used, will have a crack or chips in the fiberglass. Fair condition, will need a...

Heater Box Assembly for 1967-1968 Mustangs without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a factory type fiberglass two piece heater box/heater core casing. The heater box is a pre-assembled unit which includes the gasket and all seals. The heater plenum attaches to this assembly and directs warm air to the car. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts...

Basic clam shell box as shown for cars WITHOUT AC. Keep in mind we have nice original FoMoCo units for less money! *NOTE*Kit does not contain heater blower motor, squirrel cage, or blower motor mounting plate. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...

Used Heater Box Assembly for 1967-1968 Mercury Cougar and 1965-68 Ford Mustang without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a used factory fiberglass two piece heater box/heater core casing. We suggest purchasing the foam kit and new heater core. These used boxes are over 45 years old, there will likely be some cosmetic issues, which include minor cracks or chipped fiberglass. Clips to hold two pieces together are included. *Note...

We offer this "Core Grade" assembly for those that purchase the various 1968 reproduction bezels. This assembly will provide the needed 'guts' for the various 1968 Mercury Cougar heater control bezels. A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical switch, and hardware. Ford part # C8WA-18531.*NOTE* - Does not include knobs or cable.

Complete used heater control assembly that includes a bezel / face plate, bracket control mounting plate, electrical switches, and vacuum switches. Functional, driver quality, heater control assembly. Knobs and light socket wiring harness not included. Replaces part # D1ZZ-18A651-A. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A silver paint pen (purchased from most artist...