Heater Vents / Ducting / Defrost / Controls / other Components

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars without factor air conditioning. Cars with only the heater option had dual fresh air vents. This bezel is for the driver side fresh air vent register and control cable, it has a molded hole for the vent cable.Replaces Ford part number D1WB-65044A13-AC (cast on the part) or D1WY-6504393-A.

Chromed plastic driver side fresh air "Vent" bezel. Mounts with the cable through a hole in the dash panel, just to the right of the vent register. Most all of these used bezels have a defect in the chrome plating along the bottom, not visible when installed.Replaces Ford part D1WA-18A405 (casting in the part), or D1WY-10852-B.*Note - Does not fit Mustang

These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing.Ford part # C7ZZ-6501891.

These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing, very tough part for us to keep in stock. The metal version is a better part and you can get our metal reproduction unit right here!Ford part # C7ZZ-6501891. ...

Heater cable for Cougars and Mustangs that are not equipped with factory air conditioning. Ford Part #: D1ZZ-18518-A

Under dash bracket used to mount the pull cable for the fresh air vent on the driver side of your Mercury Cougar or Ford Mustang.

Used mounting and indexing bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket goes behind the dash panel and keeps the vent cable attached and indexed correctly. A 7/16-14  hex nut is also needed for mounting the cable. (Sold separately)Replaces Ford part number D1WY-6501822-A.

Used mounting bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket mounts to a tab on the fresh air vent, and keeps the cable stationary.  Replaces Ford part # D1WY-18C587-A.

Used steel bracket for mounting the passenger side fresh air vent cable to the bottom of the dash below the glove box. 1971-73 Mercury Cougar only.Replaces Ford part # D1WA-6501861-AC.*NOTE* Does not fit Ford Mustang.

Reproduction heater cable set for your beloved Cat or Pony. This set is an exact fit! Replaces Ford part # C7ZZ-18518-A. *Customer Feedback*     "My first deal with Don was clear back in the 1980's and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you...

Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.

Used rear window defog switch and knob assembly with mounting bracket for the 71 - 73 Standard Cougar.

Used fresh air vent duct found behind the driver side dash panel of all 1971-73 Mercury Cougar without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1WY-6501878-A.

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "A" part and may have one very minor defect. This part will be damage free. Replaces Ford part number C9ZA-18C366-A.

Lower heater duct to floor outlet for Cougars or Mustangs with air conditioning. Used grade "B" part that will have minor defects. It will have cracks or chips. Almost half the price of the grade "A" piece and works awesome if you don't have one at all. Want to have directed heating, we've got you covered. Replaces Ford part number C9ZA-18C366-A.

C9ZA-18C433-C lower heater duct to floor outlet for Cougars and Mustangs without air conditioning. Used grade "A" part and may have one very minor defect. This part might have a small crack, but it will not have any broken or missing tabs. It's good, it's cheapish, you want it.

D1ZA-18C433 lower heater duct to floor outlet for 1971-73 Mercury Cougar and Ford Mustang without air conditioning. Used grade "A" part and may have one very minor scuff. Ford number D1ZA-18C433-AD

High Quality cloth wrapped heater duct hose. This is the correct length for most cars, but will need to be cut for proper fit in some applications. Hose diameter: 2 1/2"

New clear plastic lens or face plate for the heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!

New clear plastic lens or face plate for the heater control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

New clear plastic lens or face plate for the heater control on all 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use...

New clear plastic lens or face plate for the ultra rare Power Ventilation option, heater control with power vent on all 1969 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. The Power Ventilation option added a center vent to the dash as was found on factory air conditioning cars.  Just more outside air circulation.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff...

Reproduction flexible duct end that was originally stapled to the passenger side fresh air duct, found behind the passenger side dash panel of all 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1ZA-18C305-AB.

Used fresh air vent found in the driver side kick panel of all 1971-73 Mercury Cougar without air conditioning. Replaces Ford part number D1WY-6501935-A.

Complete air vent assembly with cable, knob and bracket ready to bolt to your cowl. Replaces Ford Part # : C7ZZ-6501934-A

Our good used vents will not have cracks in the plastic or a rusty flapper from a leaking cowl. These are the same for AC and non AC.Replaces Ford part number C7ZZ-6501935-A.

New set of floor kick panel fresh air vent gaskets / seals for all 1969-1970 Mercury Cougars and Ford Mustangs. Die cut gasket copied from originals that have mounting holes in them. These foam gaskets are 1/4 inch thick. Casting number as seen on seal reads C9ZA-18B290-D. Replaces Ford part # C9ZZ-6501999.

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Due to the age, there may be a minor stress crack or blemish, it will be a good used assembly. Note that this does not come with a fan assembly, so you will need to reuse your old one. Heater core IS NOT INCLUDED. This icon means that we're looking to buy this part!WCCC is a...

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). The pictures in the sequence above are reference pictures, grade B boxes will have cracks or breaks. Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Save your old fan motor and plate, this unit does not come with a fan assembly. Grade B used, will have a crack or chips in the fiberglass. Fair condition, will need a...

We offer this "Core Grade" assembly for those that purchase the various 1968 reproduction bezels. This assembly will provide the needed 'guts' for the various 1968 Mercury Cougar heater control bezels. A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical switch, and hardware. Ford part # C8WA-18531.*NOTE* - Does not include knobs or cable.

Complete used heater control assembly that includes a bezel / face plate, bracket control mounting plate, electrical switches, and vacuum switches. Functional, driver quality, heater control assembly. Knobs and light socket wiring harness not included. Replaces part # D1ZZ-18A651-A. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A silver paint pen (purchased from most artist...

C9ZZ-18A651-A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic knobs and the lever borders. Knobs and light socket wiring harness not included. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A...

Heater control bezel for Mercury Cougars without A/C. Assembly includes bezel in A grade condition. You will most likely have to paint to match your dash color. Check back often, this type and grade of part is seldom in stock very long. Will likely have a couple of pits in the chrome plating. Almost never as nice as the one in the photo. Ford part # C7WA-18531-A.

This reproduction knob set is made by Scott Drake Enterprises. Unlike original knobs, these have a much larger font. Much easier to read while driving than the originals. Replaces Ford Part #: C8ZZ-18519

Used heater control light and socket assembly. Good for 71 - 73 Cougars with or without A/C.

For us with Cougars without factory AC. The originals were made of cardboard and are very prone to failure from moisture. These are made from virgin ABS black plastic and are excellent quality in every respect. Not often does a reproduction come along that blows away OEM, but this definitely is that part. Before you finish making your online order with us, go look at your plenum to see what condition your original is in. Replaces Ford part #: C5ZZ-18471-A

Not for use on cars with A/C. Keep in mind we also have excellent used knobs sold individually or as a set.

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.

24" hose with metal coil (like original) instead of plastic coil found in most. Coils are wrapped in a 6+ mil plastic rather than the 3 mil plastic that you can easily put your thumb through. Does not come with clips. May require being cut to fit some applications. 2 required per car. Replaces Ford Part #: B5A-18556-C.Replaces Ford Part #: B5A-18556-C.

Used cable and knob assembly for opening the driver side fresh air vent on 1971-73 Mercury Cougar without air conditioning. Cable control mounts through the dash in a special dash bezel. About 13 inches in total length.Replaces Ford part number D1WY-6501891-A.*Note - Does not fit Mustang.

Used mounting nut for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This nut screws onto the cable.  7/16-14  hex nut with 11/16" hex. (Sold separately)*Hint this is an easy to find hardware store nut, nothing else special about it.Replaces Ford part number 34670-S.

Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. New Old Stock switch and wiring pigtail with plug. Ford part # C8ZZ-18578-B

Mounts to the rear of the factory installed heater control ventilation control panel on 1967 Mercury Cougar and Ford Mustang. Switch and wiring pigtail with plug.Replaces part # C7ZZ-18578-A.

Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Switch and wiring pigtail with plug.Replaces part # C8ZZ-18578-B.

Mounts to the rear of the factory installed heater control ventilation control panel on 1967 Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1967 selector button kit. Click this LINK for shinny new button awesomeness!Ford part # C7ZZ-18578-A.

Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Ford part # C8ZZ-18578-B

This exact reproduction mounts to the rear of the factory installed heater control ventilation control panel. Save your knob or consider purchasing the 1969-73 selector button kit, find it here. Replaces Ford Part number C9ZZ-18578-A

C9ZZ-18578-A mounts to the rear of the factory installed heater control ventilation control pane. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1969-73 selector button kit. LINK This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...