Windows / Glass

Sold as a PairReplaces Ford Part #: D1ZZ-6520264-A and D1ZZ-6520265-A.

These feature all the original details. Quality rubber molded around a steel insert.Replaces Ford Part #: D1ZZ-6528182-B and D1ZZ-6528183-B.

378696-S Special set screw for the front door channel and vent window frame. This one is longer than the one that installs in the rear door window guide. This set screw has a 5/32" hex head with 5/16" NC threads and is 1-7/8 inches in overall length. This set screw also has a 1-1/8 inch diameter shoulder. Sets and holds your front door glass and vent window angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual...

375694-S2 Special set screw for the rear door guide. This one is shorter than the two that install in the vent window frame and front door glass channel. This set screw has a 5/32" hex head with 5/16" NC threads, and is 1-9/16 inches in overall length. This set screw also has a ¾ inch diameter shoulder. Sets and holds your door glass angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual for actual procedure.See...

Used windshield wiper motor cover or shield as Ford called it. Very prone to cracking and 'chalky' from age or UV light. We are not going to lie, most of these will have paint over spray or a slight amount of chalkiness. We haven't found a Ford part number other than the basic number of 17C441 which is labeled as "Shield - (Windshield Wiper Motor - Water)" as found in the Mercury MPC.

Quarter window upper adjusting screw and nut - used. Mounts to the extension assembly bracket. For all 1969-70 Mercury Cougars and Ford Mustangs. Includes bolt and nut as shown. Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang.Ford number is 381742-S2 and 376762-S2 for nut.

Used quarter window shoulder screw and nut for the 71 - 73 Cougar and Mustang.

Reproduction  Lower Windshield Moulding Center Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Used spacer for the lower windshield moulding

Reproduction  Lower Windshield Moulding Fender Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

22992 SPRING Tension spring for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

22992 "D" shaped top washer, Ford called it a 'stop'. See assembly picture. 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side, sold individually.

Reproduction stop bracket for the rear quarter window regulator on any 1967-68 Mercury Cougar and 1965-68 Ford Mustang Coupe and convertible models. Stop bracket for the quarter window regulator arm. Comes with used bolt as shown. One bracket per side, same bracket for driver or passenger side.Replaces Ford part number C4ZB-65303A12 also referenced as 29822 in the assembly manuals.Also available used. ...

Stop bracket for the rear quarter window regulator on any 1967-68 Mercury Cougar and 1965-68 Ford Mustang Coupe and convertible models. Stop bracket for the quarter window regulator arm. Comes with used bolt as shown. One bracket per side, same bracket for driver or passenger side.Reproduction also available.Ford part number C4ZB-65303A12 also referenced as 29822 in the assembly manuals. ...

Quarter window upper stop bracket

Quarter window lower stop bracket

This support bracket mounts to the lowest portion of the quarter window cavity. This bracket is installed before the lower guide bracket. Fits all 1971-73 Mercury Cougar models and 1971-73 Ford Mustang models including fastback or sport roof models. The exploded view of the quarter window parts can be found in the Osborn Body Assembly Manual for 1971-72. One for each quarter window

Used air conditioning thermostat switch for any 69-70 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash

Sold individually, two per side, four per car required. These often get destroyed when you go to replace your door window regulator slides. Two of these are used to install the C7ZZ-6523288-A track. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size)Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

Reproduction pair of vent / wing window handles for the Mercury Cougar or Ford Mustang.

Reproduction driver side (left hand) vent window frame for the Mercury Cougar or Ford Mustang.NOTE! Whereas you can make these off shore reproductions work we have found that virtually every angle, screw hole and dimension is found to be slightly to moderately off when comparing to the originals. No returns please. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

C7ZB-6522223-A Bare vent frame, no attaching parts, or glass. For all 1967-68 Mercury Cougar and Ford Mustangs. B grade quality only, will have some rust pitting.Ford Master part number C7ZZ-6522205-A. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Used driver side (left hand) vent window frame as it comes out of thedoor. This unit is just the bare window frame and will need some cleaning as itis 40 plus years old. A great option for those of you who have a limited budget. Also, because this is an original piece, it will have a far superior fit and function than the"off shore" reproductions that are currently offered.Ford part # C7ZZ-6522205-A.*Note* "B" grade will have some pitting in the chrome on theinterior side of the frame. Check...

Reproduction driver side (left hand) vent window frame for the Mercury Cougar or Ford Mustang.  This premium reproduction is a much better fit than the economy overseas version. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

Quality restoration on a clean core. Do know that some detail is lost in the polishing process. Only very minor pitting can be present on a core as deep pits are not cost effective to be restored.  Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Reproduction passenger side (right hand) vent window frame for the Mercury Cougar or Ford Mustang.NOTE! Whereas you can make these off shore reproductions work we have found that virtually every angle, screw hole and dimension is found to be slightly to moderately off when comparing to the originals. No returns please.Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

Used grade "A" passenger side (right hand) vent window frame as it comes out of the door and is just the bare window frame. This is not a perfect part but it will look good on a low mile car that shows a little patina. The weatherstrip track that continues down into the door can be had with this part for no extra charge, please mention it in the comments section when you order online. Ford part # C7ZZ-6522204-A. Casting # C7ZB-6522222-ACheck out our video below for helpful tips on...

C7ZB-6522222-A Bare vent frame, no attaching parts, or glass. For all 1967-68 Mercury Cougar and Ford Mustangs. B grade quality only, will have some rust pitting.Ford Master part number C7ZZ-6522204-A. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Reproduction passenger side (right hand) vent window frame for the Mercury Cougar or Ford Mustang. This premium reproduction is a much better fit than the economy overseas version. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

Quality restoration on a clean core. Do know that some detail is lost in the polishing process. Only very minor pitting can be present on a core as deep pits are not cost effective to be restored. Check out our video below for helpful tips on disassembling your vent and quarter windows:67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Used grade A stainless steel vent window glass frame for the left side or driver side door on a 1967 Mercury Cougar or Ford Mustang. Similar frame as the 1968

Used grade B stainless steel vent window glass frame for the left side or driver side door on a 1967 Mercury Cougar or Ford Mustang. Similar frame as the 1968

Used grade B stainless steel vent window glass frame for the left side or driver side door on a 68 Mercury Cougar or Ford Mustang. Similar frame as the 1967

Restored stainless steel vent window glass frame for the left side or driver side door on a 68 Mercury Cougar or Ford Mustang. Stainless frame portion will have a near mirror finish from polishing.NOTE: Cores should not have deep scratches or gouges

Restored stainless steel vent window glass frame for the left side or driver side door on a 68 Mercury Cougar or Ford Mustang. Stainless frame portion will have a near mirror finish from polishing.NOTE: Cores should not have deep scratches or gouges

Used grade A stainless steel vent window glass frame for the right side or passenger side door on a 1967 Mercury Cougar or Ford Mustang. Similar frame as the 1968

Used grade B stainless steel vent window glass frame for the right side or passenger side door on a 1967 Mercury Cougar or Ford Mustang. Similar frame as the 1968

Restored stainless steel vent window glass frame for the right side or passenger side door on a 1967 Mercury Cougar or Ford Mustang. Shipped bare

Restored stainless steel vent window glass frame for the right side or passenger side door on a 68 Mercury Cougar or Ford Mustang. Stainless frame portion will have a near mirror finish from polishing.NOTE: Cores should not have deep scratches or gouges

C2AZ-22963-A Special steel flat washer with flat sides for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.

Cupped metal washer with center hole with flat sides for installing the two upper swivel rollers on the rear quarter windows. 2 per side 4 total per car. Fits 1971-73 Mercury Cougar and Ford Mustang Coupe and Convertible.Ford part number D1OZ-57263A86-A.

Replaces Ford Part # : D1ZZ-7651325-A

This concours correct reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This Daniel Carpenter manufactured unit is made of slightly less dense material than the Midland unit, .75lb as compared to .85lb. If correctness is not an issue for you, you can get the Midland unit here. We have included a few comparison pictures so...

Economy overseas reproduction door perimeter seal. These glue to the perimeter of the doors and are held in by screws on both ends. Sold as a pair. Replaces Ford part #D1ZZ-6520530-A.

Premium reproduction Door Weatherstrip for the 1971 - 1973 Mercury Cougar or Ford Mustang.  These glue to the perimeter of the doors and are held in by screws on both ends.  Sold as a pair. Replaces Ford part #D1ZZ-6520530-A.

This offshore reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This overseas reproduction sold by Daniel Carpenter is simply another option to the US made version, and has been known to fit better than the US made weatherstrips. If correctness is not an issue for you, you can get the Midland unit...