All Products

NOS upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, and contours. Ford part number D1ZZ-7521-B.

Nice quality reproduction of the upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, and contours. Ford part number D1ZZ-7521-B.

Complete kit with shaft for one side. Includes grease seals and zerk fittings. Note! Often times the fine threads in the upper control arms will be worn to the point of being stripped. To keep this kit properly in place you may have to tack weld the threaded caps to the control arms in a couple of places.

New quality upper control arm shaft kit. Fits all 1967-73 Mercury Cougar and Ford Mustang, also Maverick/Comet 1970-77, Fairlane 1966-70, Torino/Cyclone 1968-71. Comes with all parts shown. This is a much better design than the original Ford design. The down fall is it does not look at all like the original Ford kit. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 681

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 682

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654607-A and are marked L.H. for the passenger side.

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654606-A and are marked R.H. for the passenger side.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Metal portion of the driver side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at least...

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Metal portion of the passenger side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at...

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # C7ZZ-6522800-C.

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: D0ZZ-6522800-A. ...

These are the cheap knockoff clamps sold by most Mustang venders as correct stamped clamps. Sold in a convenient set of 10. We highly recommend ordering the correct CONCOURS clamps! Replaces Ford Part #: C5ZZ8287-8.

Used vacuum actuator for controlling the center A/C vent on certain 1969-70 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Studs are on 1-1/4 inch centers. Common single port vacuum valve is on 2-1/4 inch centers. Ford part number C9ZZ-18A318-A. ...

Used vacuum actuator for controlling the center A/C vent on any 1971-73 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Ford part number D1ZZ-18A318-A.

Reproduction vacuum actuator for controlling dampers and levers on the different year A/C boxes. These came in several different anodized colors. This is the basic valve with a single vacuum port.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors, for 1967-68 the color was brown. This is the basic valve with a single vacuum port.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. Blue is the color found 1969 and 1970 and early 1971. Blue and Brown actuators are exactly the same. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port...

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. All bare sheet metal steel construction starting in 1971 until 1973. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port on the side.

Used ported vacuum switch with filter. Unique piece, unknown application, definitely found on a 1968. Current offering are dated 8-67, 6-68, 5-68, 7-69, 8-69. Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is...

Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number D0AE-A casting.This casting number is correct for all 1970 1971 1972 and 1973 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy...

New Old Stock Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on select Ford models. This is a NOS original electrical and vacuum operated switch. It has the FORD oval logo and part number D1AE-AA casting. This casting number is correct for select 1971 and 1972 Fords and Mercury. It was used on 302 351C and 351W engines. Because of the heavy demand placed on the cooling system by the factory air option this was mounted...

Over 100 total vacuum caps in 6 different sizes.

New old stock (NOS) brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 2 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster.  Replaces Ford part number C6AZ-9A474-A.

Used brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 3 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster. Bob Mannel's book indicates that this vacuum fitting was for A/C and Thermactor smog. Replaces generic Ford vacuum fitting part number 9A474.

Used brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 2 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster.  Replaces Ford part number C6AZ-9A474-A.

Used brass fitting found on intake manifolds 1968-69 Mercury Cougar and Ford Mustang. Usually works with an adapter that screws into the rear of the intake manifold directly. With 3 vacuum ports for various accessories and a threaded port for the hard line going to the brake booster.  Replaces Ford part number C8AZ-9A474-B.

D0ZZ-9A474-A Vacuum fitting for the rear of the intake manifold on a 1970 Mercury Cougar or Ford Mustang with the M code 351 Cleveland 4 barrel engine. Has two vacuum nipples or ports. 1970 Mercury Cougar Ford Mustang Modulation System - Bleed Assembly - Used D0AZ-12A168-C Very small inline vacuum hose bleed valve assembly installed very close to the distributor modulator control box.

Rear steel vacuum fitting for 289, 302, and 351W engines. Various applications, this one has a single port for vacuum, and a threaded top section for either a plug or additional brass fitting. See other fittings for two and four port fittings in this style of steel intake manifold fitting for 1968-69 Mercury and Ford. Replaces basic Ford part number 9A474.

Rear steel vacuum fitting for 289, 302, and 351W engines. Various applications, this one has a two ports for vacuum, and a threaded top section for either a plug or additional brass fitting. See other fittings for one and four port fittings in this style of steel intake manifold fitting for 1968-69 Mercury and Ford. Replaces basic Ford part number 9A474.

Rear steel vacuum fitting for 289, 302, and 351W engines. Various applications, this one has a four ports for vacuum, and a threaded top section for either a plug or additional brass fitting. See other fittings for one and two port fittings in this style of steel intake manifold fitting for 1968-69 Mercury and Ford. Replaces basic Ford part number 9A474.

Small Block V8 with C4 Vacuum line for 1967 - 1969 Mercury Cougar / Ford Mustang

Reproduction vacuum line, mounts into a intake manifold fitting, vacuum hose attaches and runs from the brake booster on 1968-69 Cougar, Mustang, and other Fords equipped with the 289, 302, and 351W engines and disc brakes. Hard line only, vacuum adapter fittings sold separately.

Good rust free tank taken from a Western parts car. Differs from other years in that the vacuum port is located in a different position. Located under the driver fender. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number C9WY-13A185-A.

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

Used vacuum switching manifold and electrical micro switch assembly from a 1969 to early mid 1972 Mercury Cougar and Ford Mustang. This is the all metal version vacuum distribution block. 1972 owners, please check your A/C controller to verify if you have or need the plastic version of this switch. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Used vacuum tree for any 1970 Mercury Cougar, Ford Mustang, or 1970-71 Ford Torino. This manifold assembly mounts to the firewall in the engine compartment, and is unique to the above applications, as it has 6 different vacuum outlets or sources. These connect to the brake booster, heater / air conditioning vacuum parts, and other accessory items that use vacuum. Replaces Ford part number D0OZ-9C490-A or D0OA-9C490-A.

THERE ARE NO RETURNS ON THIS PART. Not a good fit but you can make them work...You will have to elongate a couple of the small holes that mount the valance under the bumper, but not by much. Once mounted the part looks as though it was not made quite wide enough. We recommend purchasing our premium version, because honestly, you'll spend a lot of time trying to get this offshore reproduction to fit right.  Please do not call us and say you are disappointed with this part; we are telling...

Mounts on the rear of either the 289-2V or 289-4V factory cast iron intake manifold. This valve has three equal sized vacuum hose fittings in addition to the steel line going to an intake manifold vacuum source. Ford part number C6AZ-9B289-E. 1967 California emissions only.

C8TE-B-SR Correct service replacement 4490-S Carter anti backfire valve, but without the outer cover having the concours correct stampings. These units are used, not tested and one should assume they are non-functional.

Used shutoff valve for the headlight vacuum system of all 1969-70 Mercury Cougars. Also found on 1969-70 Ford and Mercury full sized cars with hidden headlights. Additionally these were also used on 1969-70 midsized Ford and Mercury such as Torino, Cyclone, also with hide away headlamps. This is a black plastic shutoff switch or connector, 1969 cars used a white valve that crumbled from the under hood heat. Note that the indicator tabs perpendicular to the lines means 'open'. Turning the valve...

This valve is used on Mercury Cougars and Ford Mustangs equipped with factory A/C to stop the flow of warm coolant when A/C is on.This valve is functionally the same as the OEM, but has obvious cosmetic differences from the factory valve.Replaces Ford Part #: C7ZZ-18495-A.

This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.

Molded "S" shaped vacuum hose. Feed hose from the smog pump to the Carter anti-backfire distribution valve.

C7OZ-6582-C Chromed valve cover with "Powered by Ford" embossed in the metal. Correct on 1967-1970 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. These are used, and will have some minor pitting or stains in the plating.Sold individually *Restoration Tip - The difference between the chromed 390GT valve cover and painted valve covers is only the chrome plating. *Note - Some 1969-70 428 Cobra Jet engines came with one of two different styles of finned cast aluminum valve covers. ...