1972 Ford Mustang

Each vent has only one of these louvers with the protruding knob.

This is a complete working assembly with outer housing. Fits driver and passenger side dash outlets, on any 1971-73 Mercury Cougar or Ford Mustang. We sell the louvers individually if your assembly is not broken and all you lack is a couple of missing fins. The fins are easily replaced as they just snap in place. The vent housing has a Ford casting number or D1ZA-6501820. Fits both the right and left sides of the dash. Center vent is different.Ford part # D1ZZ-18C366-A.

Electronic voltage regulator for use on any 1967-73 Mercury Cougar or Ford Mustang or Ford. Same foot print as originals, cover can be swapped.

New old stock NOS instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator until it is properly grounded, otherwise it...

New reproduction instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Features Solid State electronic circuitry. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator...

Features the proper cover and original logos. I A S F stamped on cover. Replaces Ford Part #: D2TF-10316-A. The voltage regulators listed in this section are poor quality. We suggest you buy a reliable, modern, solid state unit and just use the cover we sell as a stand alone product. We will not warranty the mechanical voltage regulators you see here, the quality is poor.

Features the proper cover and original logos. I A S F stamped on cover.Replaces Ford Part #: D2AF-10316-A. These new voltage regulators are improved and more reliable than the units we've sold previously.

Starting in 1972 the 'Fasten Seat Belt' warning light was relocated to the center of the dash for visibility of all occupants of the vehicle. This is a tested, and working seatbelt warning light fits into the steel holder on the instrument clusters of all 1972-73 Mercury Cougar and Ford Mustangs.Ford part number D2ZB-10C859-AA. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50%...

Cupped metal washer with center hole with flat sides for installing the two upper swivel rollers on the rear quarter windows. 2 per side 4 total per car. Fits 1971-73 Mercury Cougar and Ford Mustang Coupe and Convertible.Ford part number D1OZ-57263A86-A.

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

Water By-Pass Hose with 351W Motorcraft® logo and part number imprinted in white ink. Stamped with C9OE-8597-D.

OEM replacement water pump for the 351 Cleveland. Gasket included. Replaces Ford Part #: D0AZ-8501-E.

OEM replacement Water Pump for the 351 Windsor. Gasket included. Replaces Ford Part #: D0OZ-8501-A.

Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.

Reproduction water bypass plate for all Ford 351C engines. This is an original style brass restrictor plate for 70-73 Cougar, Mustang, Torino etc.Must be used in conjunction with the correct 180 degree thermostat.For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

New water restrictor plate for the Mercury or Ford equipped with the 351 Cleveland engine. It has been an accepted fact for decades now that the 351C bypass system was not the greatest idea Ford ever came up with. The unique 351C thermostat "hat" never seals well, causing a certain portion of coolant to just circulate through the block and never make it to the radiator. Years ago, Pantera enthusiasts (all Panteras had cooling issues from the factory BTW) found that if they soldiered a penny...

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

Replaces Ford Part # : D1ZZ-7651325-A

Economy overseas reproduction door perimeter seal. These glue to the perimeter of the doors and are held in by screws on both ends. Sold as a pair. Replaces Ford part #D1ZZ-6520530-A.

Premium reproduction Door Weatherstrip for the 1971 - 1973 Mercury Cougar or Ford Mustang. These glue to the perimeter of the doors and are held in by screws on both ends.  Sold as a pair. Replaces Ford part #D1ZZ-6520530-A.

Reproduction door glass to roof weatherstripping for your Mercury Cougar or Ford Mustang. An inexpensive way to better seal the interior space of your Cougar or Mustang.Replaces Ford part #'s D1ZZ-6551222-A and D1ZZ-65223-A.

Keep in mind not all gaskets are created equal... Many of these gaskets are made by two or three different makers. We have used these gaskets ourselves on our own Cougars with success, and know which ones fit correctly and which ones will stand the test of time. You may save a dollar or two buying elsewhere on some of these items but is it worth it? Ask the person selling the item if they personally have ever used the part. Replaces Ford part #D1ZZ-6542084. Installing the gasket yourself? you...

Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

New old stock driver side (left hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang.  Ford part number D1ZZ-6530147-A.

Reproduction driver side (left hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium piece made with the original Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Reproduction passenger side (right hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium unit that made made with orginal Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Replaces Ford part #: D1ZZ-7653986. Seven piece kit with attaching hardware.

Driver side stainless steel weather strip retainer for 71-73 Cougar and Mustang convertibles. This retainer screws to the windshield pillar post and holds the weather stripping for the front of your door window glass. Plan on replacing the weatherstripping. There is also the companion lower aluminum retainer listed on our site.These used stainless pieces generally polish up very well with 0000 steel wool. The little black plastic coated clip will be compromised due  to age and...

Passenger side stainless steel weather strip retainer for 71-73 Cougar and Mustang convertibles. This retainer screws to the windshield pillar post and holds the weather stripping for the front of your door window glass. Plan on replacing the weatherstripping. There is also the companion lower aluminum retainer listed on our site. These used stainless pieces generally polish up very well with 0000 steel wool. The little black plastic coated clip will be compromised due to age and heat.Replaces...

Used driver side (left hand) aluminum channel for installing the roof side, or upper door and quarter window weatherstripping. Right and left sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5392. Shipping...

Used passenger side (right hand) aluminum channel for installing the roof side, or upper door and quarter window weatherstripping. Passenger and driver sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item...

Used, driver side, front lower, aluminum channel section, for installing the roof side or upper door and quarter window weatherstripping. Right and left sides are contoured differently, for the 1971-73 Mercury Cougar and Ford Mustang coupe and convertibles. These channels also have pre-drilled holes for installation, often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip. Piece...

Used, passenger side, front lower, aluminum channel section, for installing the roof side or upper door and quarter window weatherstripping. Right and left sides are contoured differently, for the 1971-73 Mercury Cougar and Ford Mustang coupe and convertibles. These channels also have pre-drilled holes for installation, often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip....

Replaces Ford part #: D2WY-6543720.

Replaces Ford part #D1ZZ-7602626, right is the same as left, sold as a pair. Includes mounting screws.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. 184 pages.

Sold individually, phosphate & Oil (gray-black).

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems. Specifically for installation of the new Legendary GT7 and 1966 Shelby wheels. Thread Size: 1/2" Bolt Pattern Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems for installation of the new Legendary aluminum wheels. These really only fit the Magstar style wheels; we recommend the 3/4" lug nuts for all the other Legendary wheels for clearance reasons. Conical Head: 13/16" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...