1972 Ford Mustang

D1AE-9425-DA Cast iron intake manifold used on all 1971-72 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D1AE-9425-DA. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D1AZ-9424-D. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

Reproduction intake manifold valley pan for the Mercury Cougar or Ford Mustang equipped with the 351 Cleveland engine with the 2V (2 barrel) heads.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar.

Great option for international customers. Light weight, and all you need is a PC or laptop, and you can plug this drive in and access all the same information that you'd find in the full sized shop manual books.

Includes the controller and switch to convert your standard two speed wiper system over to delay wipers.Controller part #  D1ZB-17C476, D2ZB-17C476, MPC # D1ZZ-17C476-A.Switch part # D1ZB-17A553-BB, D2ZB-17A553-AA, MPC # D1ZZ-17A553-B.

This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A

Stainless steel battery hold down bolts. Work with standard battery hold down brackets and the billet hold down bracket.

For use on Hard Top / Coupe.

This decal goes on the tire jack itself.

Reproduction Jack Instructions Decal for the 1971 - 1973 Mercury Cougar

Used jumper wire with correct ends for doubling back on the tachometer leads from the under dash harness. Works for all generations 1967-68, 1969-70, and 1971-73 Ford anything and Mercury, and Mercury Cougar with factory tachometers. If your tachometer goes bad, you will not start or keep your engine running. Good for bypassing tachometers for testing and getting home. Keep in your glove compartment or tool box.

Electrical junction block for use on 1971-73 XR7 models or 1971-73 Ford Mustang with options such as convertible, power seat, power windows, or rear defog. This combination insulator / junction block is for securing a circuit breaker, and mounts near the starter solenoid. Made from black Bake-O-Lite, Grade B, these will have some chipping or cracking present. Replaces Ford part number D0SB-14448-A or D0SZ-14448-A.

Reproduction keeper clip that attaches to the secondary articulating stabilizer arm and slides into place to secure the pin that holds the arm.

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford #: C7AZ-6222053-A.

Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford Part #: C7AZ-6243562-A.

Key reminder and headlamp reminder buzzer for 1972-73 Mercury Cougar and Ford Mustang. Also used on Many other Ford, Mercury, and Lincoln vehicles in this time frame. Can also be stamped D2AB-13150-A1A D2AB-13150-A2A. Ford master part number D0AZ-13150-E. All buzzers are bench tested prior to shipping.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the ignition / door key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

This rod was used on all Cougars 1971 - 1973 equipped with a 351 and FMX transmission both 4V and 2V. Approximately 27" Black color code.

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part numbers D1WB-6502345, D2WB-6502345, D3WB-6502345.

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part number D1WB-6502344, D2WB-6502344, D3WB-6502344. ...

Reproduction headlight switch knob for the 71 - 73 Cougar.

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-ACheck out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

During installation, check for proper alignment with trunk latch. Trunk latch and striker should engage smoothly, both items are adjustable. We only save the rust free latches with no wear or rust, the rest are tossed. Fits 1971-73 Mercury Cougar and Ford Mustang. Ford part number D1AZ-6543252-A.

Reproduction driver side (left hand) convertible top latch assembly for the Mercury Cougar or Ford Mustang.  

Reproduction passenger side (right hand) convertible top latch assembly for the Mercury Cougar or Ford Mustang.  

Used convertible top latch handle for the driver side (left hand) for the Mercury Cougar or Ford Mustang.Ford part # D1ZZ-7650509-A , casting # D1ZB-7650509-A

Used convertible top latch handle for the passenger side (right hand) of the Mercury Cougar or Ford Mustang.Ford part # D1ZZ-7650508-A , casting # D1ZB-7650534-AA

Used steel lateral support brace for Cougars and Mustangs with the 351-2V or 351-4V engines after 4/27/1971. Replaces part # D1AZ-2888-A.

Replacement "cool white" LED single post light bulb for 67-73 Cougar and Mustang courtesy light applications. Can also be used for trunk lights, under hood lights, under dash lights, and more. Good replacement for "97" bulb applications. Some may find Our Plasma bulbs too bright for the Opera Lights and prefer to tone it down with these.

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522811-A

Reproduction Legendary Series GT5 Alloy Wheel. This updated design was created using state of the art casting technology for superior strength and precision. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium...

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with natural aluminum accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction Legendary GT9 series aluminum wheel in the gloss black finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black...

Reproduction Legendary GT9 series aluminum wheel in the charcoal finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the natural finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the gloss black finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black...

Reproduction Legendary GT9 series aluminum wheel in the charcoal finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the natural finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the gloss black finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black...