Mouldings & Trim

This original FoMoCo, six piece windshield trim set for the Mercury Cougar convertible. Because these pieces are original pieces, they will have far superior fit when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well. The four upper pieces are wider than the coupe versions, but the lowers are the same (with about an inch cut off the ends). The trim is... trimmed so it will fit underneath the pillar trim pieces. *NOTE* If your trim has...

Restored five piece windshield trim set has been restored beyond the original luster. Keep in mind only cores with minor dings, dullness and scratches can be accepted. Kinked, gouged, and flattened cores will not be credited. This windshield moulding set fits the 1967-1968 Mercury Cougar as well as the 1964 1/2 - 1968 Mustang Coupe and Fastback. Ford part numbers for these pieces include: C5ZZ-6503136-B, C5ZZ-6503137-B, C5ZZ-6503144-B, C5ZZ-6503145-B, and C5ZZ-6503148-D. *NOTE* If...

Good used five piece windshield moulding / trim set as taken from a parts car. Finish will be dull and some pieces may have minor scratches, but overall, this set is ready to install and will look decent as is. Ford part numbers for these pieces include: C5ZZ-6503136-B, C5ZZ-6503137-B, C5ZZ-6503144-B, C5ZZ-6503145-B, and C5ZZ-6503148-D. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. ...

This 3-piece blemished front trim set and a scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot, a slip on the buffer wheel... There are many reasons why we label our restored trim parts as blems. We carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to. From 10-15 feet away these look as good as our...

These restored mouldings have the correct "bright dip" anodized finish and look almost like NOS! This set is offered at a great price and is better quality than many NOS trim parts as they often show the scars of 40 years of shelf wear. Note, we cannot restore torn, smashed, or heavily damaged cores. If you are in question as to whether your cores can be restored or not please send us a picture and we will let you know whether you should send them to us for credit or exchange. *Tip* Even if...

This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.You can find our reproduction pair of brackets here. ...

These aluminum ninety degree brackets are what fastens the XR7 chrome boot moulding to the quarter panels. The beltline weatherstip also attaches to them. These parts are only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.

This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.You can find our reproduction pair of brackets here. ...

Chromed quarter window moulding or 'hockey stick' mounting bracket for the driver side only of 1967-68 Mercury Cougars. Also attaches the outer window fuzzy or belt line kit component. Stainless steel construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C7WY-6529035-A

Chromed quarter window moulding or 'hockey stick' mounting bracket for the passenger side only of 1967-68 Mercury Cougars. Also attaches the outer window fuzzy or belt line kit component. Stainless steel construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C7WY-6529034-A

New pan head screws for installing the tail light bezel on any 1971-73 Mercury Cougar. Sold individually, a total of 16 are used to install the brake light bezels (8 per side). #8 black pan head Phillips screw 1-1/2 inches long. Replaces Ford part number 56001-S.

Keep in mind you can get FREE trim parts from us if you have a quantity of good quality cores to exchange!Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...

If you happen to have a set of three NOS wheel lip mouldings and purchase the fourth as a restored piece from us it will visually fit right in. Restored is never as good as NOS as the polishing process will make the part thinner which means it will be more prone to damage than an un-restored original or NOS trim part. Note! Road trash of all sorts, sand, gravel, etc. ends up in the gutter to the right hand side of the road. The front tire tends to form a vacuum and sucks stuff away from the...

*NOTE* Due to the difficulty in obtaining 69 aluminum trim we no longer sell these without first having you send us your cores. Keep in mind we pay well for quality 69 hood lip mouldings. Do not contact us with pretzel shaped parts, parts you have attempted to fix or flattened out parts. We need trim parts showing only minor dings / dents, scratches and dullness. All of our aluminum trim parts come with the correct anodized plating just like Ford did them in the day. We are just as excited to...

If your core is not adequate we have cores for sale. Keep in mind you can get FREE trim parts from us if you have a quantity of good quality cores to exchange!Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. For more info on aluminum trim restoration & core exchanging, check out our video below. ...

Front passenger side wheel lip moulding that has been lovingly restored to a better than new condition. Far superior fit and finish when compared to "offshore" reproductions. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your RESTORABLE cores. Do you have questions about your cores trim pieces? This video should help! ...

This purchase requires you send a good core in advance. If you happen to have a set of three NOS wheel lip mouldings and purchase the fourth as a restored piece from us it will visually fit right in. Restored is never as good as NOS as the polishing process will make the part thinner which means it will be more prone to damage than an un-restored original or NOS trim part.*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by...

Rear passenger side wheel lip moulding that has been lovingly restored to a better than new condition. Far superior fit and finish when compared to "offshore" reproductions. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your RESTORABLE cores.

This is the left hand or "Driver Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6529035-A. We have found that this 3M product works great for bonding these parts in place...

Spot on reproductions of the 1969-70 Quarter Window "Hockey Stick" Moulding priced below what you can have pit free originals re-chromed for. We have found that this 3M product works great for bonding these parts in place permanently. Included with the moulding is super strength 3M double sided, trim tape.Ford part number C9WY-6529035-A.*NOTE* Remember to remove the aluminum bracket from the bottom of your old hockey stick, it is needed to attach to the car and for attaching the outer...

Reproduction driver side (left hand) passenger side (right hand) pair of quarter window mouldings / trim with used mounting brackets attached. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting. We bond these to the mounting brackets in house with a liberal application of 3M Windo-Weld #08609. The factory bonded them together with 3 studs that were heat peened / swedged. Ford part...

This is the right hand or "Passenger Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6551728-A.We have found that this 3M product works great for bonding these parts in place permanently....

This is the right hand or "Passenger Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place.We have found that this 3M product works great for bonding these parts in place permanently.Ford part number C9WY-6529034-A.*Note - Remember to remove the aluminum bracket from the bottom of your old hockey...

Chromed quarter window moulding or 'hockey stick' mounting bracket for the driver side only of 1969-70 Mercury Cougars. Coupe only, will not fit convertibles. Also attaches the outer window fuzzy or belt line kit component. Aluminum construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C9WY-6529035-A

Chromed quarter window moulding or 'hockey stick' mounting bracket for the passenger side only of 1969-70 Mercury Cougars. Coupe only, will not fit convertibles. Also attaches the outer window fuzzy or belt line kit component. Aluminum construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C9WY-6529034-A

This is the stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Stang. This is a very hard part to come by in good shape. Many times body shops will loose this piece while replacing the top. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Driver side used, 1969 Sport Special rocker moulding retainer.  This black plastic part mates the scoop to the aluminum mouldings. Ford part numbers C9WB-65101B63-A. Fits: 1969 Mercury Cougar Sport Special

Passenger side used, 1969 Sport Special rocker moulding retainer.  This black plastic part mates the scoop to the aluminum mouldings. Ford part numbers C9WB-65101B62-A. Fits: 1969 Mercury Cougar Sport Special

Sold as a pair. These black plastic parts mate the scoops the aluminum mouldings. Ford part numbers C9WB-65101B62-A and C9WB-65101B63-A Fits: 1969 Mercury Cougar Sport Special

Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually.NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to apply too much pressure, causing unwanted bending.

Used plastic rocker moulding clip for 1968 Mercury Cougar and 1967-68 Ford Mustang. Used clip, originally pop riveted onto the rockers. Sold individually. Ford part number C7ZB-6510182-A.

Set of 13 black Phillips oval headed screws for attaching the face pads onto 1967 Mercury Standard Cougars (non-XR7 models). Sold as a set of 13 screws, also sold individually under SKU 100022556. *Note - These screws are a glossy black in color.

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

These are not available new and differ from Mustang. We on occasion find one that is still pliable and intact.Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

These are not available new and differ from Mustang. We on occasion find one that is still pliable and intact. Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

Contoured stainless steel trim for the driver side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A15-A. Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Used (poor condition) weather strip may or may not be in place. Please go to our rubber section to select the new rubber strips...

Unlike our un-restored used door glass trim and are sold in pairs only. If you are doing a concours correct restoration then these would not be for you as they have been "over restored" to a mirror like finish. The down fall of having such a mirror like finish is they get finger prints on them every time you touch them. The good part is they look HOT! Very nice touch to that resto-mod that cannot get enough bling.When sending cores, they must be in good shape or an upgrade core fee will apply....

Contoured stainless steel trim for the passenger side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A14-A Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Sold separately, please choose between driver or passenger side. Used (poor condition) weather strip may or may not be in place....

This is the passenger side trim / moulding that mounts to the door window and creates the seal between the door glass and the quarter window on 69 Cougars and Mustangs. Get the seal you need for this moulding here.

We claim that in time every nut bolt and clip will be documented on this site! Here is yet another tiny little, one year only trivial part that only the most detailed enthusiast will even care about. This little part is designed to space the column cover away from the metal lower dash so as to prevent dash squeaks. They are left natural, never painted (the one shown has surface rust). Two are required per car, they are sold individually. These little parts are often missing and of course not...

Restored decorative driver side sport special rocker panel scoops for the 1969 Mercury Cougar. To be eligible for the core charge refund, you must send in pitt free cores.

Restored decorative passenger side sport special rocker panel scoops for the 1969 Mercury Cougar. To be eligible for the core charge refund, you must send in pitt free cores.

Reproduction decorative sport special rocker panel scoops for the 1969 Mercury Cougar.Sold as a pair.

Restored decorative sport special rocker panel scoops for the 1969 Mercury Cougar. To be eligible for the core charge refund, you must send in pitt free cores. Sold as a pair.

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.