FoMoCo/MotorCraft

Single cylinder head from 1967 Mercury Cougar with non smog 289 engines, 289-2V and 289-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 54-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.3:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C6OE-M or C6OE-6090-M.These weigh...

Single cylinder head from 1968 Mercury Cougar 289 engines without smog. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 61.7-64.7 cc's. With stock pistons, these heads will net an approximate compression ration of 8.7:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C8OE and "289".*Note - These low compression heads are not...

Single cylinder head from 1967 Mercury Cougar with California smog 289 engines, 289-2V and 289-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 54-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.3:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C6OE-M. *Note - These...

Single cylinder head from 1968 Mercury Cougar 302-2V engines without smog. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 61.7-64.7 cc's. With stock pistons, these heads will net an approximate compression ration of 8.7:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C8OE-J and "302" and "2-V".*Note - These low compression heads...

Single cylinder head from 1968 Mercury Cougar 302-4V engines without smog. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 52-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C8OE-D and "302" and "4-V".Current casting dates include: 7G25,...

Single cylinder head from 1970-73 Mercury Cougar with H code 351C-2V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.04 and 1.65 inch valves, and the chambers measure out at 78.2 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0AE-J. 2V in the...

Single cylinder head from 1969 Mercury Cougar H or M code 351W engines, 351-2V and 351-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C9OE-6090-A.These weigh 53 lbs. each, and cannot be combined with other items unless shipping truck freight. ...

Single cylinder head from 1970 Mercury Cougar H code 351W engines, 351-2V. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0OE-6090-C. 1970 351 Windsor engine, not to be confused with the 351 Cleveland engine from the same year.These weigh 53 lbs. each, and cannot be...

The W code Cougar 427 GTE used these heads on a side oiler rotating assembly with a hydraulic cam and Medium Riser aluminum intake - the so called "PI" C7AE version. 427 cylinder heads that have the J's have provision for 14 bolt exhaust manifolds. Low Riser 427 heads use 2.09" / 1.66" valves. Included is a set of machined used valves (16 total)  The C8AE-6090-J heads were also used on the prototype 50 Mustang fastbacks used at the 1968 Winter Nationals - the so - called "135 series"...

Single cylinder head from 1967 Mercury Cougar with 390-4V engine with California thermactor smog ports. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes. Current...

Single cylinder head from 1972 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.6:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D1ZE-6090-GA. 4V in...

Single cylinder head from either a 1968 X code 390-2V or 1969 Mercury Cougar with 390-4V or 390-IP engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1 (9.5:1 with X code). Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes....

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. These cylinder heads are factory drilled and tapped for thermactos smog tubes. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust...

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped holes for exhaust manifolds. These weigh 48 lbs. each, and cannot be combined with other items...

For all H code 351-2V engine codes with singles exhaust. Includes 1970 351C or Cleveland engines. Holds the rear of the muffler to the passenger side underside body. Ford part number C9WY-5260-A.

D0AE-9430-B 351-4V Cleveland factory original cast iron exhaust manifold for passenger side. At some point there may have been a D0AE-9430-G casting number used, which may be substituted as per the Master Parts Catalog. Same manifold 1970-1973. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

D1ZE-9431-AA or D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.

D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. Same casting as D1ZE-9431-AA used 1971-72ish.*351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.

Single 390GT cylinder head for a 1968 S code 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. These are the GT exhaust manifolds with 14 drilled and tapped exhaust bolt holes. This cylinder head has 4 drilled and tapped, thermactor...

Good used double sheave alternator pulley.Ford Part #: C5AF-10A352-J.

Wiring harness segment to the convertible power top pump on any 1971-73 Mercury Cougar or Ford Mustang. Part number D1ZB-15A668-AB.

Wiring harness segment from firewall to the convertible power top switch on any 1971-73 Mercury Cougar or Ford Mustang.  Part number D1WB-15A690-AA.

Wiring harness under hood segment from circuit breaker through the firewall to the convertible power top switch on any 1971-73 Mercury Cougar or Ford Mustang.  Part number D1ZB-15A669-A.

C5ZZ-7210-C Shift lever for all 1967 Mercury Cougar and Ford Mustang and 1968 until 1-2-1968. The early lever can be identified by measuring the distance between bolt holes. 1-13/16" spacing between the holes is the C5ZZ-7210-C lever. *Note - Must be used with Trunion C5ZZ-7210-D, sold separately.