Steering

Used lower steering column mounting bracket at firewall, for any 1971-73 Mercury Cougar or Ford Mustang. Rubber seal will need to be replaced, see related items for rubber seal.  Ford part number D1ZZ-65017A50-A.

This used upper column bracket bolts to the brake pedestal bracket under your dash. The two threaded studs face downward and are used to attach the lower column bracket.

Used tilt column vacuum can bracket for the 1968 Mercury Cougar *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

One year only design.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away vacuum reservoir in place. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement...

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away vacuum reservoir in place. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement...

Power steering hose bracket for early model Mustangs.

Used original lower power steering hose mounting bracket for 289 / 302 / 351 1967-69. Comes as shown with rubber insulator. This used version has the indexing tab which the reproduction does not. May come with new bolt and or rubber insulator.Replaces Ford part # C7DZ-3A609-A, C7DZ-3A610-A, C7ZZ-3C510-B, and C8ZZ-3C510-A.

New reproduction of the grommet found at the bottom of nearly any Ford steering column starting in 1970 for the transmission lockout rod. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

These are OEM replacement bushings. The problem with these are most original sets are rusted out on the metal parts. We highly recommend the upgrade, unitized sets we sell over the orignal design.Replaces Ford Part #: C6OZ-3A187-A

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.

Great Reproduction of an Often Broken Part. This part fits on the bottom of the steering wheel and must be in place to cancel your turn signal on tilt column cars. Used on all Ford products with a tilt column 1967-69. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

Factory original turn signal canceling cam. Originals were molded in white, reproductions are molded in black. Repros also available from us. Without this part that self attaches to the back of your factory steering wheel, you will be turning off your blinkers manually. Click up, click down... *NOTE* We have no good reason to encourage you to purchase this hard to find original over the reproduction, unless you just gotta have it. **NOTE** Need help diagnosing a Cougar turn signal problem?...

Used cap for the index lever tension spring for the Mercury Cougar or Ford Mustang equipped with the tilt/tilt away steering column. Two required per car.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Due to the vulnerable location of the control valve these often get cracked or worn through from rubbing on other components. Fits most all Ford passenger cars 1962-1970. Replaces Ford part number C2AZ-3C705-B

Replaces Ford part # C7AZ-3A006-C of D1VY-3A006-A.

Replaces Ford part # C7AZ-3A006-C or D1VY-3A006-A.

1967 - 1971 Ford power steering pump dipstick. Used until 2-8-1971.

1971 - 1973 Ford power steering pump dipstick. Used starting 2-8-1971.

New castle nut for all power steering control valve ball stud found on 1967-70 Mercury Cougar and Ford Mustang. 3/4 inch hex nut, with 1/2-20 threads. Connects the Pitman arm to the ball stud on the P/S control valve. Don't forget the cotter pin. Verify your shop manual for correct year torque specifications. We found one source of 28-35 FT LBS. for the Pitman Arm nut to control valve. Ford numbers for attaching nut: 1967-68 351059-S, 1969-70 385002-S.

Reproduction D0ZZ-3304-A Manual steering drag link for all 1970 Cougar and Mustang and 1969 Boss 302 Cougar Eliminator & Boss2 Mustang with a non-power assist manual steering system. This is the same as 1969 manual steering drag link, but with larger holes for 1970 ball joints. Meaning more heavy duty, Boss2 specifications if you will. *Note - if installing on a 1969 Mercury Cougar or Ford Mustang, you will need to use 1970 inner tie rod ends. 

C7ZZ-3304-A Manual steering drag link for any Cougar or Mustang from 1967 - 1968 with a non-power assist manual steering system. *Concours tip - This is a natural cast iron part that originally had a pink stripe for identification on the assembly line.

C9ZZ-3304-A Manual steering drag link for most 1969 Cougars and Mustangs (excludes G code Boss 302 cars) with a non-power assist manual steering system. 1969 Boss 302 Eliminators and Mustangs used a heavier duty drag link that was adopted for use starting in 1970, on all Cougars and Mustangs. *Concours tip - This is a natural cast iron part that originally had a pink stripe for identification on the assembly line.

Power steering drag link for any Cougar or Mustang from 1967 - 1968 with factory power steering system. *Concours tip - This is a natural cast iron part that originally had a yellow stripe for identification on the assembly line.Replaces Ford part number C7ZZ-3304-B .

C9ZZ-3304-B Power steering drag link for most 1969 Cougars and Mustangs (excludes G code Boss 302 cars) with a factory power steering system. 1969 Boss 302 Eliminators and Mustangs used a heavier duty drag link that was adopted for use starting in 1970, on all Cougars and Mustangs. *Concours tip - This is a natural cast iron part that originally had a pink stripe for identification on the assembly line.

Power steering drag link for all 1970 Cougar and Mustang and 1969 Boss 302 Cougar Eliminator & Boss2 Mustang with power assist manual steering system. This power steering drag link may have a 1970 part number, but it is basically the same as the 1969 Boss 302 version, which was much thicker than the standard 1969 power steering drag link. Can be installed on 1969 Mercury Cougar and Ford Mustangs as long as you upgrade to 1970 inner tie rods.The 1970 drag link measures about 0.850 inches...

Steering drag link for all power steering and non-power steering Cougars and Mustangs from 1971 - 1973.Replaces Ford part number D3ZZ-3304-A .

Used centering ring for any fixed or tilt column on a 1968 Cougar or Mustang.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used centering ring for any fixed or tilt column on a 1969 - 1973 Cougar or Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This one in, one out design was unique to the early 1967 Cougar for the headlights. Also found on vacuum controlled options like the 1967 Mustang Cougar tilt / tilt-away steering column. This is a good used unit that has been tested and found to hold vacuum well. This valve is located a few inches behind the carburetor.

Two required per car, early 67 used a chrome version of this screw. Later years used this screw.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction clevis for the tilt/tilt away steering column equipped Mercury Cougar or Ford Mustangs. This unit attaches the pawl cable to the vacuum motor shaft. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used retaining clip for the adjustment bar in the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. Two required per car, used to hold the tilt position adjustment bar in place.  * While not technically correct, this also will work for 1970 - 1974 Cougar/ Mustang tilt columns. SOLD INDIVIDUALLY*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Used clip for the adjustment tension spring for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This item holds the release bale to the upper knuckle. It is different than the 67 - 69 clip although both can be used. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used steering column shroud or collar for any 1971-73 Mercury Cougar or Ford Mustang. These come in various colors, and have a smooth texture. These will have some scratches in the surface, specify your desired color in the notes or comments section, but do know that black is in short supply. Ginger anyone?*Note does not include the retainer or clip, we cannot keep them in stock.Replaces Ford part numbers D1ZA-3530-A, D1ZZ-3530-A,D3ZA-3530-A, and D3ZZ-3530-A. ...

Used in all of 1970 and the early part of 1971. This collar uses the 'small' access plate cover. Ford master part number D0AZ-3D505-A, casting number on the part is D0AA-3D505. Nice condition, no cracks or damage. Also fits 1970-71 Lincoln MKIII and Thunderbird.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

One year only part not found on any other car except Cougar and Mustang with tilt. If you would like to run a 1968 or newer steering wheel on your 1967 then you need to exchange this cover with the version found on the 1967 Thunderbird which has no lip at the top. We have these in stock and would enthusiastically trade it for the Cougar / Mustang upper cover. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This Thunderbird collar is a good substitute for those wanting to put an after-market or 1968 up steering wheel on their 1967 Cougar / Mustang. We also suggest purchasing this collar when installing our reproduction 1967 Mustang deluxe steering wheel.  *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used upper steering column cover for the Mercury Cougar or Ford Mustang equipped with the tilt/tilt away steering column. This unit comes naked with no attaching parts or fasteners.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. WCCC no longer has an in-house service for tilt and tilt-tilt away steering columns 1967-1979. After 2...

This complete four piece kit is for any small block 289, 302, or 351 Windsor Cougar 1967, 1968 and 1969. 

This complete four part kit is correct for any 1967-68 small block 289 or 302, and 351 Windsor Mercury Cougar or Ford anything 1967, 1968 and 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut.If you do not have a air conditioning you will need a spacer in place of the round spacer shown. If you have the 351 Windsor without A/C, you will need a the rectangular spacer which is sold separately.

This complete four part kit is correct for any 1969 small block 351 Windsor Mercury Cougar or Ford anything 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut. If you do not have a air conditioning you will need a the rectangular spacer which is sold separately.

This is a complete shaft. Lower, upper and knuckle. This shaft may have plastic pins broken due to age and handling. It is functional. May have light rust and knuckle will have been tightened if needed.

Exact reproduction horn ring contact components for the standard horn ring used on two spoke steering wheels, replaces Ford part # C9AZ-13A805-B. Includes new hardware

Premium quality original FORD valve that has been re-manufactured to original tolerances. Quality part that is rebuilt by a true craftsman here in the USA. *NOTE: Our rebuilt and reproduction control valves all come pre-lubed with the correct amount of grease. If out of the box you add more grease, you will damage the valve. Unlike some suspension parts these are not designed to add grease until you see the grease coming out of the seal. Our warranty does not cover over lubricating. ...

Unfortunately we have had a high rate of returns due to failure on these and can no longer enthusiastically recommend them. Please consider our original rebuilt units. This is the large nut control valve that Ford switched to after 1967. Many 1967 Cougars have been converted to the 1968 valve over the years so you may want to double check your valve before ordering. These units are designed to use type F fluid, not off the shelf power steering fluid. Please follow the procedures for...