Steering Columns & Parts

Vacuum / electric tilt away solenoid for the 1969 Mercury Cougar and Ford Mustang. Original Ford part number C9ZZ-3D536-A. These vacuum tilt solenoids are tested and guaranteed to work. Bench testing the 1967-69 tilt away release solenoid: Verify that there is continuity between the two electrical spade connectors. No continuity means the the windings in solenoid windings are bad. This is a bad solenoid. Next, put vacuum to the lower port (10-17 inches of vacuum) any handheld or car vacuum...

Vacuum reservoir that mounts under the battery tray for factory tilt swing away steering columns. Fits Cougar, Mustang, and Thunderbird. Single nipple tank, we also sell the double nipple tank for the 1967-68 tilts. Replaces Ford Part # C9ZZ-3E547-A. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* WCCC...

Used rubber washer for the locking pawl cable to cable guide used for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This unit fits against the cable side of the ninety degree angle. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts...

Used wire extension for the tilt / tilt away steering column found in the Mercury Cougar or ford Mustang. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts needed. To offset the cost of your rebuild, you can send us additional parts or parts columns and we will give...

Used jumper wire used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction tilt / tilt away steering column wiring harness for the Mercury Cougar or Ford Mustang. Exact copy in every way! If you call and tell us the long sad story of how when you pulled your column in 1982 in a bone yard and left this harness behind unknowingly. we will have to charge you extra... Just kidding! *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Reproduction wiring harness for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is an exact replica right down to the stripes. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used wiring harness for the 1969 Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used tilt / tilt away steering column wiring harness for the 1969 Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction of the upper steering column bearing for your 67* - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. You can find the lower bearing here. Outside diameter: 1 3/16 " Inside diameter: 15/16 "Thickness: 1/4" Replaces Ford Part Numbers: F23Z-3517, C1AA-3517-A, C3AZ-3517-A, C7SZ-3517-D, D0AZ-3517-A, F23Z-3517-B * - may not fit some 67 Mustang applications with a fixed column as these used Ford...

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.

Used plastic bushing for the lock pawl rod guide for the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. These delicate little bushings are needed to keep the lock pawl rod in alignment with the vacuum motor shaft. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Good used upper collar for the tilt column on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Tilt steering column cover plate for turn signal lever. Two versions, two different sizes of openings for the turn signal wand. Original used Ford part, plan on painting to match your steering column. Fits all 1970-71 Mercury Cougar, 1970 Ford Mustang, and other Ford/Mercury cars with factory tilt steering columns. Replaces Ford part number D0AA-9D793-AW.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

This is the electrical portion of the new for 1970, locking column mounted switch. This is the rod actuated device mounted on the top of your column under the plastic collar cover. See page 33-02-06 of your 1970 shop manual for proper installation and adjustment. Working, used ignition switch. This is only the electrical side, the mechanical key and lock section is not included. These are tested and repaired as necessary by our Electrical Dept. Ford part number D0AZ-11572-A. While there's...

Ford part number 3E629. Molded rubber construction, fixed and tilt steering columns. These may have been used as early as late 1972, not sure. Limited stock. The reproduction plastic version for 1969-72 will also fit and work in conjunction with the available foam insulation. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used emergency flasher knob for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is a very fragile part which we never find in good used condition. What you will see when it has been broken off is an exposed Phillips screw head. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang.  There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

New manufactured Tilt / Tilt-Away cable for any 1968-69 Mercury Cougar or Ford Mustang with factory tilt steering column. All new parts developed by our in house steering column expert DW. Not created from used parts. The cable sheathing will not split or crack over time like the originals.Replaces Ford part number C9ZZ-3E520-A*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

One required per car, mates to female version attached to the under dash loom. Same plug for tilt and non tilting columns.

Good used part without excessive rust or damaged rubber. For use with fixed column only. 1971-73 rag joints are different than the 1967-70 variety. The 1971-73 Cougar and Mustang steering box has a larger diameter shaft for attachment. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1967 1968 1969 1970 Cougar tilt columns, differs greatly from the fixed column version in that is has a "D" shaped fitting on the column side. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse your existing 12 point bolt for the other end or purchase a second one. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1971 1972 1973 Cougar tilt columns. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse one of your factory ones. Splined end slightly larger than previous years, due to the upgraded integral steering box unique to the later Cougars. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Identified with the straight bracket compared to the 1968 relay which has a bend. Keep in mind we have a reproduction substitution for this part. Ford part # C7ZA-3E553-A. Ford packaging reads C7ZZ-10B926-A *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Helpful tip:  For those having trouble getting their tilt away mechanism to...

New old stock tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight.  Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.co...

Used in the latter part of 1967 and all of 1968 and 1969 to fasten the upper column cover to the column. Early 1967 used a chrome version of this screw.

Used steering wheel tension spring used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. Keeps tension on the steering wheel shaft so as to keep the steering wheel from contacting the upper column cover. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC...

1971 Complete, solid Mercury Cougar / Mustang tilt column with no missing or cracked parts. Rebuilt with the inclusion of a fixed lower shaft which eliminates the need for the hard to find (and expensive) tilt rag joint. No change to the installation, or function, and will be in stock more often than our full priced 1971 tilt column. Although they may look much alike, each year 1970 - 1973 is unique. Every column we sell has been disassembled and reconditioned by our full time in house tilt...

1972 Complete, solid Mercury Cougar / Mustang tilt column with no missing or cracked parts. Rebuilt with the inclusion of a fixed lower shaft which eliminates the need for the hard to find (and expensive) tilt rag joint. No change to the installation, or function, and will be in stock more often than our full priced 1972 tilt column.Rebuilt with the inclusion of a fixed lower shaft which eliminates the need for the hard to find (and expensive) tilt rag joint. No change to the installation, or...

1973 Complete, solid Mercury Cougar / Mustang tilt column with no missing or cracked parts. Rebuilt with the inclusion of a fixed lower shaft which eliminates the need for the hard to find (and expensive) tilt rag joint. No change to the installation, or function, and will be in stock more often than our full priced 1973 tilt column. Although they may look much alike, each year 1970 - 1973 is unique. Every column we sell has been disassembled and reconditioned by our full time in house tilt...

1970 Mercury Cougar / Ford Mustang columns were a weak design from the factory. We find that all the columns we get have some degree of excessive play, some will not even hold position. The design was improved upon greatly as the years went by and spending a little more on an updated / rebuilt one is well worth the investment. This is a 100% complete column with key and all parts needed to convert from a fixed to a tilt column. You can use your existing plastic plastic color keyed collar and...

1971 Complete, solid Mercury Cougar / Mustang tilt column with no missing or cracked parts. Although they may look much alike, each year 1970 - 1973 is unique. Every column we sell has been disassembled and reconditioned by our full time in house tilt column specialist. If you do not currently have a tilt column do know you will get every part needed to make the conversion.  Often times we are unable to stock 1971-73 tilt columns due to not having tilt rag joints. We now offer a reduced...

Complete, solid tilt column with no missing or cracked parts. Easy to install and is as comfortable of an upgrade as you maybe imagining it to be. Although they may look much alike, each year 1970-73 is unique. In my opinion this upgrade enhances your cars value in direct proportion to its cost and will not cost you points in judged shows as it was a commonly installed dealer option. Often times we are unable to stock 1971-73 tilt columns due to not having tilt rag joints. We now offer a...

1973 Complete, solid Mercury Cougar / Mustang tilt column with no missing or cracked parts. Although they may look much alike, each year 1970 - 1973 is unique. Every column we sell has been disassembled and reconditioned by our full time in house tilt column specialist. If you do not currently have a tilt column do know you will get every part needed to make the conversion.  Often times we are unable to stock 1971-73 tilt columns due to not having tilt rag joints. We now offer a reduced...

This is my favorite Cougar - Mustang - Shelby option of all time! In fact as a rather tall person that is not as slim as I once was, I do not really enjoy daily driving a Pony car that does not have this option. This column does not only manually adjust up and down with the depression of the turn signal wand towards the dash, it also releases and swings up and towards the passenger side of the car each time the ignition is turned off and the door is opened. To start the car you must close the...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Vacuum / electric tilt away solenoid for the 1968 Mercury Cougar and Ford Mustang. These vacuum tilt solenoids are tested and guaranteed to work. When bench testing the 1967-69 tilt away release solenoid, verify that there is continuity between the two electrical spade connectors. No continuity means the the windings in solenoid windings are bad. This is a bad solenoid. Next, put vacuum to the lower port (10-17 inches of vacuum) any handheld or car vacuum source will work. The solenoid housing...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used vacuum reservoir for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This is a 1967 only design that is very hard to find in rust free condition with a working vacuum check valve. Beware of substitutes as there are close facsimiles with different sized nipples, different brackets or plastic built in check valves. These versions off later model cars...

Used wiring cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Unique to the 1968 and 1969 tilt column, fixed column version will not fit on a tilt without modification. Ford part number C8ZZ-13376-A or C8ZZ-13376-B.