Interior

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

We cannot provide new units anymore but we do stand behind this used unit for 30 days.Check out the video below on our new gauge tester: ...

This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

Perfect fit, great reproduction. These plastic discs are found on all 69-70 convertibles on the rear of both decor and xr7 interior levels. We are unclear as to all the "exact" applications on all years and models but one application we have verified is the fronts of 1971 - 73 Cougars equipped with standard interior. The reason the standard interior 71-73 Cougars came with these is that the door panels were very thick on the 71-73 decor / XR7 models and quite thin on the standard models and...

This handle is a good replacement for the window cranks found on the 1971 - 1972 Cougar both front and back. The originals were 4 1/4" total length and this replacement handle is 4 7/8" long. The important detail on these is the fact that the female portion that attaches to the splined window regulator protrudes from the back 5/16". If you are using our chrome backing plates on your 69 -70, then this is the crank you will need to provide the correct clearance.Used before 10/71,...

Used on both the front and rear of the 1971-1972 Mercury Cougar produced before 10/1/71. The picture above shows the difference between the early version (right) and the later version (left). Plan on purchasing new knobs to go with the bare crank, we have 7 different colors to choose from. See related items. Inquire about a B grade knob if you are looking for something just so that you have a window crank. Ford Part # D0AZ-7630322-A, casting # as seen on the back D1AB-7630322-AWA. ...

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part #C8AZ-6223352-GR *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part Number #C8AZ-6223370-ADiameter 1-1/2"

Consolette wiring harness, bridges the main under dash wiring harness and the ashtray light pigtail. Not for full length consoles. Ford part # D1WB-15A056-AB.

Used steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1970-72 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968-69, Ford, Mercury, & Lincoln. This plug is black, there is also a natural or white color version of this plug used by Ford 1968-69. Ford part number D0AZ-14489-L.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the...

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Listing is very good quality wood grain insert only. Plastic will be broken. The difference between 71 and 72-3 is that 71 has no provision at the top for the seatbelt warning light.

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

Reproduction pair of black seat belt buckle bezels for the Mercury Cougar, Ford Mustang, or Ford Torino. It is little details like these that often make the difference between first and second place at the show. 

Core driver side (left hand) and passenger side (right hand) pair of bucket seats with center seat release for the Mercury Cougar or Ford Mustang. The seat frame is the same in the standard, decor or XR7 and are the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These units will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available...

Core driver side (left hand) bucket seat frame with center seat release for the Mercury Cougar or Ford Mustang. This unit is the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket...

Grade A used driver side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260763, D3ZB-6561633, D1FZ-6260763, D2ZZ-6260763, and D3ZZ-6560763. We also have B...

Grade A used passenger side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260762, D3ZB-6561632, D1FZ-6260762, D2ZZ-6260762, and D3ZZ-6560762. We also...

New Old Stock console lid catch. Plastic piece that screws to the underside lid of your late 1970-73 Mercury Cougar or 1970-78 Ford Mustang. Yep, used on Mustang II's, too.  Ford part number D0ZZ-63060A96-B and stamped into the plastic D0ZB-63060A96-B ...

NOS plastic brackets that screw to your roof and then slide a vinyl colored piece over. Sold individually, two are required per car. Ford part # C8AZ-6229232-A.

NOS white colored coat hooks pair. Reproductions only come in black, these are new in the package. White color started in 1970, off white and parchement 1968-69. Fits 1968-73 Mercury Cougar and Ford everything including that Mustang. Ford Part #: D0AZ-6229024-K.

Good used upper collar for the tilt column on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This desirable option was used only on the driver side seat of the LATE 71-73 Cougar and Mustang. This is for seats that have the seat release knobs on the outsides of the seats. The early 71's had the release in the center of the seat. It can be installed on the passenger side with no modification other than extending the wiring that runs under the carpet.  Before we send out a system it will have been tested and will work in all positions and will not show excessive wear or...

Tilt steering column cover plate for turn signal lever. Two versions, two different sizes of openings for the turn signal wand. Original used Ford part, plan on painting to match your steering column. Fits all 1970-71 Mercury Cougar, 1970 Ford Mustang, and other Ford/Mercury cars with factory tilt steering columns. Replaces Ford part number D0AA-9D793-AW.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...

This grade A pad for a 71 - 73 is truly a rare find. We only obtain an excellent pad like this every year or two. Grade A pads will have no cracks and will not be curling on the edges. Contact us for color on hand as the picture shown is not the actual pad you will get.

This grade B dash pad will have multiple cracks and will only be usable as a core to adhere our dash repair shell to. Get the shell here.

Used door / lid for the glove box in the Mercury Cougar, grade "A", no cracks, chips or scrapes. This is just the bare inner and outer door / lid and does not come with the hinge, liner, lock or lock bezel. To prevent damage to the plastic glove box door, the inner steel backer should be removed and file 1/16" off of one or both sides. Cracking is due to shrinkage of the plastic glove box door over time.Plan on painting to match your interior. Ford part # D1WY-6506024-A for the inner,...

Bulk pack of 100 oval head phillips screws for door and window crank handles.

This is an original chrome lock knob used on 1968 and up Fords with no peeling chrome or obvious scratches. If you compare the originals to the reproductions we have listed you will see a distinct difference. This is for the very particular restorer who really is concerned about detail, especially on prominent pieces like this. Sold individually, very limited supply.Original Ford part number is C8AZ-6221850-A

Very nice condition, may need repaint but will have no tears, rips, burns or broken backer boards. Sold as a pair. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay...